金属加工设备 / 铣床 / 万能升降台铣床
生产厂家: DMG MORI
型号:NVX 5100
机械类型: Universal Knee-Type Milling Machines
产品编号: 170177439
数量: 1
日期： 12.09.2026
价格:
Seller-item-No.:051482
| Characteristics | |
| Maximum load (table centre) | 1200 Kg |
| Dimensions (L x W x H) | 3,02 x 2,98 x 2,61 m |
| Rapid feed X / Y / Z | 30/30/30 m/min |
| Movement X / Y / Z | 1050/530/510 mm |
| Spindle taper | BT 40 |
| Tool Magazine with | 30 Positions |
| Drive power (25% DC) | 37 kW |
| Drive power (100% DC) | 22 kW |
| Table surface | 1350 x 600 mm |
| Speed max. | 12000 rpm |
| Weight approx. | 7000 Kg |
| General | |
| Vertical Machining Center; Control: Control M730UM with CELOS | |
| CELOS - ERGOline Touch | CELOS - ERGOline Touch to facilitate machine operation incl. 21.5 ERGOline Touch ® control with multi touch screens Uniform management, documentation and visualization of order, process - and machine data Networkable with CAD / CAM User friendly and p |
| High-torque spindle 12,000min-1, 37/ 22 kW (#40) | High-torque Spindle 12,000 min-1, 37/22 kW (#40) Motor spindle powerMASTER® Spindle speed: 12,000 min-1 Output: 37/22 kW (50/30 HP) (10%ED/cont) Torque: 360/177 Nm (265.52/130.55 ft·lbf) (10%ED/cont) MASTER series spindle: Covered by a 3-year warrant |
| Spindle Taper 7/24 Taper #40/ Grip MAS
|
Spindle Taper 7/24 Taper #40/ Grip MAS |
| Preparation for Center Through-spindle coolant system | Center Through-Spindle Coolant System It can supply coolant through the holes of the spindle and tool. The coolant supply path to the tool tip is a center-through type. Effective for removing chips, cooling a machining point and prolonging a tool life. |
| Retention Knob: Special (Center-Through) (7/24 Taper #40) | Retention Knob: Special (Center-through) (7/24 Taper #40) The spindle collet applicable to the special (center-through) retention knob is installed. Tool retention knob is not included. The through-spindle coolant specification requires a dedicated r |
| Interface for Hydraulic fixture (hydraulic 2 circuits ) | Interface for Hydraulic Fixture (Hydraulic 2 Circuits) For the fixture interface, hydraulic 2 circuit 4 ports are provided on the in- machine ceiling (right side). The hydraulic unit (made by NACHI) put on the oil pan with casters is placed at the rear |
| Interface for Workpiece seating detection (2 lines) | Interface for Workpiece Holding Detection (2 Circuits) For the workpiece holding detection interface, pneumatic 2 circuit 2 ports are provided on the in-machine ceiling (right side). The panel is installed on the upper right of the machine front and the |
| Tool storage capacity 30 tools (#40, STD) | Tool Storage Capacity 30 Tools (#40 Standard) Ring type magazine Tool Storage Capacity: 30 tools Technical random address type |
| Chip conveyor internal (spiral) + external (hinge type + drum filter type) (NVX5100) | Chip conveyor internal (spiral) + external (hinge type + drum filter type) (NVX5100) Install spiral conveyors inside the machine and a chip conveyor to discharge chips (ConSep2000) to the rear of the machine. The chip conveyor installed to the machine rea |
| Interface for Through-spindle Coolant System (7.0 MPa, Variable Pressure Steps) (KNOLL/ Interlit) | Interface for Through-spindle Coolant System (7.0 MPa, Variable Pressure Steps) (KNOLL/ Interlit) Interface for mounting the high-pressure coolant system (separate type). Supplies the high-pressure coolant to the tool tip from the center of the spindle |
| Mist collector Interface (duct only, dia. 200 mm ) | Mist Collector Interface (Duct Only, Dia 200 mm (7.874 in) ) Interface for attaching a mist collector to collect dust and particles and to condense oil mist and smoke generated during the machining process. Includes only the duct outlet from the machine b |
| Oil Skimmer | Oil Skimmer It removes oil floating on the coolant in the tank to extend coolant life by attaching the oil to the surface of the rotating belt. It is recommended to use it with the water-soluble coolant. The belt is made of polyurethane. Do not use it |
| Right side shutter | Right Side Shutter The shutter vertically opened/closed with the pneumatic cylinder drive is provided at the right side. Opening dimension: W 700 mm×H 983 (27.56 inch.×38.7 inch.) Distance from the floor to the lower end of the opening: 930 mm (36.6 |
| Interface for Robot (EtherNet/IP), Need to select EtherNet/IP Interface | Robot I/F (EtherNet/IP), Separate EtherNet/IP I/F Required The interface signals for mounting robots are made available. The signals are exchanged with the robots using the EtherNet/IP communication protocol. The use of the robots allows the automatic loa |
| High column 200 mm | High column 200 mm This option allows you to place a liner between the column and the bed, and to extend the Z-axis travel by 200 mm. Since the gauge line position during Z-axis zero point return gets higher, large workpieces can be machined. The dist |
| Water-glycol chiller (Chilling unit) (install on machine type) (#40) | Water-glycol Chiller (Chilling Unit) (Install on Machine Type) (#40) Cools the spindle motors and bearings according to a rise in the machine body temperature. Since it synchronizes to the machine body temperature, it is less susceptible to room temper |
| 10 external M-codes | 10 External M-Codes 10 M-codes are added for general purpose use by customers. The terminal blocks are provided for output/completion of the added M-codes. When the M-code is specified, the signal is output to the terminal block relayed to the relay ci |
| Setting Unit mm | Setting Unit, MM The unit to be used for the screen display and program commands is set to millimeter (mm). Turning: MM specification for the turret Horizontal machining center: MM specification for the tapped pallet |
| MPC (Machine Protection Control) | MPC (Machine Protection Control) It monitors vibration with acceleration sensors mounted on the spindle. This technology cycle stops the spindle to minimize the damage to the machine when abnormal vibration value is detected. It is also equipped with |
| MVC (Machine Vibration Control) | MVC (Machine Vibration Control) It is technology cycle for supporting the optimal machining by controlling vibrations. The acceleration sensor mounted in the spindle detects the vibration, and displays optimal machining conditions based on the vibratio |
| Islands, open pockets | Islands, open pockets Islands - Programming process can be greatly simplified because minimum input operation is required even for the complex machining. Open pockets Definition of open pockets eliminates tool paths with no machining allowance, |
| High-speed canned cycle | High-speed canned cycle High-speed cutting can be specified with one line of program. This function enables the user to reduce programming time by adding a new cycle that can create a high-speed, time saving complicated programs. |
| Coordinate system rotation | Coordinate system rotation The shape specified by a program can be rotated. By using this function, for example, if a mounted workpiece is located at the position where the machine coordinate is rotated, offset can be applied by the rotation command. F |
| Special equipment | RMS-Sensor |
