We use cookies to optimize our website for you and to be able to continuously improve it. By continuing to browse the site you are agreeing to our use of cookies.
Disagree
Max tube diameter 76 mm Max thickness 3 mm Max bending degree 180 Bending radius max 260 mm
used
Description: For processing pipe ends Incl. manual operation from the manufacturer ELETTRONICA Type: VT 110weight approx.: 700 kg, Approx. Onsite Dimension. (l x w x h): 1,600 x 900 x 1,700 mm
used
Max. tube diameter 45 Bending capacity of thick walled tube 2 Arbor length 4.000 mm Equipped with: With dies
new
Bending capacity: Copper or brass tube: 54 x 4 mm Steel tube: 54 x 2 mm Stainless steel pipe AISI 304/316: 42 x 3 mm Hydraulic tube ST35: 54 x 4 mm Furniture construction tube: 54 x 3 mm Aluminium tube: 54 x 5 mm Gas pipe for piping: 1 1/2 " Maximum bending angle: 210° Engine power: 1,1 kW Voltage: 400 V Machine dimensions (W x D x H) without stand: 800 x 300 x 680 mm Approximate weight: 107 kg Scope of delivery: Bending segment 1/4 "G (Ø 13.72 mm) incl. counter rollers and race Bending segment 1/2 "G (Ø 21.3 mm) incl. counter rollers and race Bending segment 1 "G (Ø 33,7 mm) incl. counter rollers and race Bending segment 1 1/4 "G (Ø 42.25 mm) incl. counter rollers and race
used
Key data: 32 mm, 2 mm
Inv. Num. : 6997 Type: CMH 32 NC Producer: Cansa Generated: Parameters: Maximum tube diameter: 32 mm Maximum pipe wall thickness: 2 mm Maximum bending angle: 1900 st Power consumption: 4.4 kW Mandrel length: 2000 mm Max pressure: 120 bar Equipment: Hydraulic clamping Hydraulically controlled mandrel Hydraulic collet Colour touch screen Display of the current position of the pipe on the monitor (displacement and rotation) Display of the daily production on the screen of the control system Display error messages on the control system screen Saving created programs in the memory of the control system Ability to store up to 100 bending programs
used
Description: bending diameter range for bending strength modulus (RS=250N/mm2): ,1.3 m3 maximum pipe diameter: ,32 mm minimum pipe diameter: ,4 mm maximum pipe length for mandrelless bending: ,9999 mm minimum pipe length for bending with a mandrel: ,4450 mm  , single dimensions machine: 5200 x 1000 x 1200 mm control cabinet: ,600 x 900 x1900 mm  , set includes a safety mat, a SICK light curtain and tools but only those visible in separate photos (not mounted on the machine) offer does not include fences or other tools mounted on the machine  , please also have a look at the PDF document of this machine tube length max.: 9,999 mm, weight approx.: 2,000 kg, Approx. Onsite Dimension. (l x w x h): 5,200 x 2,000 x 1,900 mm
used
Crippa tube bending machine 955LE CNC tube CNC tube bender Ø30 x 2 mm (max. Ø55 mm) - Tube wall thickness – 2.0 mm (max. 2.5 mm) - Tube material - steel - Bend radius 72, 90, 100, 150 mm (max. 250 mm) - 3-axis bending It was never working – new, but the production year ca. 2015
used
Inv. Num. : 5725 Type: A 89 TNCB Producer: CSM Created: 2014 Parameters: Maximum bending angle: 180 pcs Total power requirement: 15 kW The largest profile: 60x60x6 mm bending radius in the middle of the tube: 350 mm bending radius in the middle of the profile: 300 mm Machine height: 1200 mm Machine length: 4700 mm Machine width: 1200 mm Machine weight: 2500 kg
used
Hand-hydraulic tube bending machine with hinged bending frame for pipe Ø: 3/8 - 3"
used
Description: Bandwidth 100 mm Belt length 2000 mm Tube diameter 25.4 - 76.2 mm Angle adjustable from - to 30 - 90 degrees Connection voltage 400 V Total power requirement 4.0 kW Machine weight approx. 0.2 t Space requirement approx. 0.5 x 1.5 x 1.5 mweight approx.: 200 kg, Approx. Onsite Dimension. (l x w x h): 500 x 1,500 x 1,500 mm
new
tube diameter: 2 x 3,91 mm STtube diameter: 60 x 4,5 mm GASrevolutions per minute: 2,5 U/minradius: min. 2 x D mmbar material - diameter: 35,0 mmtotal power requirement: 1,5 kWweight: 130 kgFurnishing:- mandrelless tube bending machine- mechan. Angle adjustment via dial- Tool holder: hexagonal 40 mm + 50 mm- Bending angle: 0 ° to 180 ° (max. 210 ° angle of rotation)- Bending radius: R10 to R270 mm- integrated chassis Bending segments on requestThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
new
tube diameter: 33,7 x 3,4 GAS mmtube diameter: 35,0 x 2,5 STAHL mmbending radius min.: R10 - R 190 mmtube diameter: 35,0 x 1,5 EDELST mmbending angle max.: 0 - 180 °tool taper: 6-kant 40 mmvoltage: 230 Vtotal power requirement: 0,9 kWweight of the machine ca.: 23,0 kgDescription :- MediBender 070 digital- with maximum bending power steel tube 35 x 2.5 mm- Excellent bending quality with very tight bending radii (from 2 x tube Ø) & Bending angles between 0 ° to 180 °- Easy handling- High accuracy and reliability- Quick tool change (within a few seconds)- Easy to transport- A huge selection of inexpensive standard tools (metric, gas inch, inch) Bending segments available for an extra charge STAHL bending segment R-82 G-1 ... 308 euros SLIDING SHOE brass 1 gas = 33.7mm ... 93 eurosThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
used
bending radius min.: 10 - 300 mmBending Angle: 0 - 180 °0: 1,25 / 2,6 U/minMotor Capacity: 1,5 kWweight: 135 kgThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
used
Description: Hydraulic press for crimping hydraulic pipes, equipped with all the necessary matrices for pipes from 0.5 to 50 mm, never used 0 hours packed in wooden crateweight approx.: 270 kg, Approx. Onsite Dimension. (l x w x h): 1,000 x 800 x 1,000 mm
used
Description: Hydraulic press for crimping hydraulic pipes, equipped with all the necessary matrices for pipes from 0.5 to 50 mm, never used 0 hours packed in wooden crateweight approx.: 270 kg, Approx. Onsite Dimension. (l x w x h): 1,000 x 800 x 1,000 mm
used
Description: Hydraulic press for crimping hydraulic pipes, equipped with all the necessary matrices for pipes from 0.5 to 50 mm, never used 0 hours packed in wooden crateweight approx.: 270 kg, Approx. Onsite Dimension. (l x w x h): 1,000 x 800 x 1,000 mm
used
Description: Hydraulic press for crimping hydraulic pipes, equipped with all the necessary matrices for pipes from 0.5 to 50 mm, never used 0 hours packed in wooden crateweight approx.: 270 kg, Approx. Onsite Dimension. (l x w x h): 1,000 x 800 x 1,000 mm
used
Description: Hydraulic press for crimping hydraulic pipes, equipped with all the necessary matrices for pipes from 0.5 to 50 mm, never used 0 hours packed in wooden crateweight approx.: 270 kg, Approx. Onsite Dimension. (l x w x h): 1,000 x 800 x 1,000 mm
used
Description: Hydraulic press for crimping hydraulic pipes, equipped with all the necessary matrices for pipes from 0.5 to 50 mm, never used 0 hours packed in wooden crateweight approx.: 270 kg, Approx. Onsite Dimension. (l x w x h): 1,000 x 800 x 1,000 mm
used
Description: Hydraulic press for crimping hydraulic pipes, equipped with all the necessary matrices for pipes from 0.5 to 50 mm, never used 0 hours packed in wooden crateweight approx.: 270 kg, Approx. Onsite Dimension. (l x w x h): 1,000 x 800 x 1,000 mm
used
Description: Hydraulic press for crimping hydraulic pipes, equipped with all the necessary matrices for pipes from 0.5 to 50 mm, never used 0 hours packed in wooden crateweight approx.: 270 kg, Approx. Onsite Dimension. (l x w x h): 1,000 x 800 x 1,000 mm
used
Description: Hydraulic press for crimping hydraulic pipes, equipped with all the necessary matrices for pipes from 0.5 to 50 mm, never used 0 hours packed in wooden crateweight approx.: 310 kg, Approx. Onsite Dimension. (l x w x h): 1,000 x 1,000 x 1,400 mm
used
Description: Hydraulic press for crimping hydraulic pipes, equipped with all the necessary matrices for pipes from 0.5 to 50 mm, never used 0 hours packed in wooden crateweight approx.: 310 kg, Approx. Onsite Dimension. (l x w x h): 1,000 x 1,000 x 1,400 mm
used
Description: Hydraulic press for crimping hydraulic pipes, equipped with all the necessary matrices for pipes from 0.5 to 50 mm, never used 0 hours packed in wooden crateweight approx.: 310 kg, Approx. Onsite Dimension. (l x w x h): 1,000 x 1,000 x 1,400 mm
used
Description: Hydraulic press for crimping hydraulic pipes, equipped with all the necessary matrices for pipes from 0.5 to 50 mm, never used 0 hours packed in wooden crateweight approx.: 310 kg, Approx. Onsite Dimension. (l x w x h): 1,000 x 1,000 x 1,400 mm
used
Description: Hydraulic press for crimping hydraulic pipes, equipped with all the necessary matrices for pipes from 0.5 to 50 mm, never used 0 hours packed in wooden crateweight approx.: 310 kg, Approx. Onsite Dimension. (l x w x h): 1,000 x 1,000 x 1,400 mm
used
Description: Unused item: Power: ,380 v  ,dimensions: length 750 mm, width 500 mm, height 950 mm. Weight: 220 kg.  , Hydraulic pipe pressweight approx.: 220 kg, Approx. Onsite Dimension. (l x w x h): 750 x 500 x 950 mm
new
tube diameter: 16 / 12 mmwall strength: 1,5 mmbending radius min.: je nach Rohr r2 bis 3 x d total power requirement: 1,2 kWweight of the machine ca.: 0,5 tShaft diameter 20 mm (standard)Max. Bending radius 60 mmMax. Bending capacity steel 12 x 1.5Stainless steel 12 x 1Copper soft 16 x 1Length feed (accuracy): with electrical drive 0.1 mmRotation (accuracy): with electrical drive 0.1 °Three-jaw chuck: YesVoltage NC 2 / NC 3: 230V / 400VThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
new
sheet width: 1050 mmplate thickness: 3,0 mmpre-bending: / required space: 2,08 x 0,7 x 1,25 mweight of the machine ca.: 410 kgSheet width: 1050 mmSheet thickness: 3.3 mmRoller diameter - top: 110 mmRoll diameter - un: 110 mmTotal power requirement: 1.1 kWMachine weight: 1080kgMachine width (mm): 850Machine length (mm): 1820Machine height (mm): 1150The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
used
Description: Bandwidth 75 mm Belt length 2000 mm Belt speed 2850 m/min Connection voltage 400 V Total power requirement 4.0 kW Machine weight approx. 0.18 t Space requirement approx. 0.5 x 1.4 x 1.2 m,weight approx.: 180 kg, Approx. Onsite Dimension. (l x w x h): 500 x 1,400 x 1,200 mm
used
Description: Hydraulic pipe bender Compressive force 16t 8 pcs. Bending elements from 1/2 'to 3'weight approx.: 45 kg, Approx. Onsite Dimension. (l x w x h): 800 x 700 x 300 mm
used
Description: Combined belt grinding and pipe grinding machine - Abrasive belt K 40 - with 7 pcs. sanding rollers. 20, 28, 32, 41, 48, 60 and 76mm Sanding belt direction left / right Band width 100 mm Belt length 2000 mm Belt speed 15/30 m / sec Tube diameter 20 - 76 mm Angle adjustable from - to 30 - 90 degrees Connection voltage 400 V Total power requirement 2.5 / 3.3 kW Machine weight approx. 0.19 t Space requirement approx. 1.2 x 0.75 x 0.7 mweight approx.: 190 kg, Approx. Onsite Dimension. (l x w x h): 1,200 x 750 x 700 mm
used
Description: Combined belt grinding and pipe grinding machine - Abrasive belt K 40 - with 7 pcs. sanding rollers. 20, 28, 32, 41, 48, 60 and 76mm Sanding belt direction left / right Band width 100 mm Belt length 2000 mm Belt speed 15/30 m / sec Tube diameter 20 - 76 mm Angle adjustable from - to 30 - 90 degrees Connection voltage 400 V Total power requirement 2.5 / 3.3 kW Machine weight approx. 0.19 t Space requirement approx. 1.2 x 0.75 x 0.7 mweight approx.: 190 kg, Approx. Onsite Dimension. (l x w x h): 1,200 x 750 x 700 mm
used
Description: Pipe grinding / Burnishing - for sanding, satin finishing, and high-gloss polishing - large wrap angle of 270 ° for efficient work - Belt speed continuously adjustable - flexible and handy - perfect for railing construction Connection voltage 230Volt Power 800W Tape dimensions 40 x 760mmweight approx.: 4 kg, Approx. Onsite Dimension. (l x w x h): 60 x 220 x 180 mm
max. tube Ø: 6 - 48.3 mm Max. bending angle: 0 - 360° electr. Connection: 400 V, 1.8 kW Dimensions: 4200 x 1300 x 700 mm Weight: approx. 300 kg
used
Description: Machine number: 551 Power: 1000 W For pipes up to max. 35 mm diameter (Attention: see photographed technical plate as wall thickness plays a role) With accessories as shown in the picturesweight approx.: 40 kg, Approx. Onsite Dimension. (l x w x h): 700 x 600 x 400 mm
used
Unbek. Type, YOC ca. 1990, Revision 2002 Specifications: - Bending capacity at 45 kg / mm² up to approx. Ø 25 x 3 mm - Bending angle left + right selectable - Hydr. Double-sided bending function - Hydr. Delivery ° - Drive 400 V / 11 kW - Space requirement approx. W 1750 x H 2200 x D 2300 mm - Weight approx. 1600 kg - with - bending angle adjustment - Hydr. Voltage - Bending tools
used
Description: serial number: KOSPAR/2025/08/2017 working hours: power on time: approx. 5460 hrs. run time: approx. 3129 hrs. cutting time: approx. 1233 hrs.  , max. component diameter: ,160 mm min. component diameter: ,50 mm max. component length: ,1000 mm min. component length: ,100 mm max. spindle working speed: ,1400 rpm min. spindle working speed: ,600 rpm  , overall dimensions including with all conveyors: ,5500 x 5450 x 2400 mm  , transport dimensions: machine: ,5100 x 1700 x 2400 mm feeder: ,2200 x 1400 x 1300 mm receiver: ,2200 x 1400 x 1300 mm chip conveyor: ,4950 x 1000 x 1900 mm  , tools are not included in the offer except the standard set of 4 clamping jaws  , please also have a look at the videos and the PDF document of this machine weight approx.: 6,700 kg, Approx. Onsite Dimension. (l x w x h) ...
used
Offer 23246 Specifications: - Bending performance - Tube at 45 kg / mm² Ø 6 - 48 mm - Max. bending angle 180 ° - Max. bending radius 145 mm - Drive 400 V / 1.7 kW - Space requirement approx. W 900 x H 1100 x D 1400 mm - Weight approx. 600 kg -with - Tubular circular saw - Inside and outside pipe end burr device - Mandrel bending device approx. 2000 mm - hydr. Spine Retraction - various bending tools as shown
used
Description: Set of 5 manual tube bending machines Different sizes New and unused weight approx.: 40 kg, Approx. Onsite Dimension. (l x w x h): 900 x 500 x 500 mm
used
roll diameter: 50 mmroll diam. toproll: 155 mmroll diam. bottom roll: 155 mmtotal power requirement: 1,5 kWdimensions of the machine ca.: 1000x750x1400 mmweight of the machine ca.: 400 kgThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
used
tube diameter: max 60 mmwall strength: 3 mmbending capacity pipes: 60 x 3 mmweight of the machine ca.: 2000 kgdimensions of the machine ca.: ca. 8000 x 1300 x 1200 mmincluding a lot of accessories6 mandrels, mandrel extension length 6000 mm and various bending tools (see photos)The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
new
Original MINGORI® Model OB40 - Mobile hydraulic tube bending machine with manually operated hand pump, suitable for bending pipes according to DIN, API and ASA standard, as well as coated PE-HD pipes. The machine works in the compression bending process. The greatest surmountable material resistance torque that can be overcome with the machine is about 28 cm³. Maximum bending force 18 tons Maximum bendable pipe diameter 88.9 mm Smallest possible bendable pipe diameter 17.2 mm Smallest bending radius depending on the radius of the bending punch from 46.5 mm to 330 mm Smallest bending angle 110° (this machine also available for bending angles up to 180°) Weight of the basic machine approx. 140 kg The machine is delivered in a storage chest – Dimensions of the chest approx. 102 x 32 cm x H 41 cm Weight basic machine 140 kg With electrically operated hand pump (as mo ...
used
Specifications Ø tubes / radius in mm: Ø 22 / 67 Ø tubes / radius in mm: Ø 10 / 36
used
Description: PLC control Max. wire thickness W=4.3mm / t=1.4mm Machine is fully functional and is sold without coil feed.weight approx.: 1,500 kg, Approx. Onsite Dimension. (l x w x h): 2,000 x 1,500 x 2,000 mm
OSTAS ROUND BENDING MACHINE TYPE SMR 1070 x 96 - Capaciteit 1070 x 3 mm - Conisch walsen - Wegdraaibare bovenrol - Voetbediening - Noodstop - Documentatie - 400V DUTCHMACH Metalworking machines ENSCHEDE - NETHERLANDS (3 km from the German border)
new
OSTAS ROUND BENDING MACHINE TYPE SMR 1070 x 96 - Capaciteite 1070 x 3 mm - Conisch walsen - Pathdraaibare bovenrol - Voetbediening - Noodstop - Documentatie - 400V DUTCHMACH Metalworking machines ENSCHEDE - NETHERLANDS (3 km from the German border)
new
CNC – controlled profile and tube bending machine for demanding and precise bending work with hollow sections and tubes. With our machines, aluminium – steel / stainless steel – various plastics such as PVC window profiles (depending on the application) can be bent with repeatable accuracy, regardless of the material. Depending on the equipment, our machines can also be used for three-dimensional bending work. Our REPANDUS models can work both horizontally and vertically. The models of the REPANDUS series work with a fixed upper roller and two movable lower rollers – this means that the straight end piece is relatively short compared to machine concepts with fixed lower rollers. The machine body is made of vibration-absorbing cast steel Shaft diameter of upper and lower rollers Ø 70 mm Shafts made of special steel – hardened and ground Bending force 190 kN Maximu ...
used
Description: Machine number 38003897weight approx.: 100 kg, Approx. Onsite Dimension. (l x w x h): 1,200 x 500 x 1,200 mm
used
Description: tube diameter: 75 mm consisting of three parts:  , 1/3 preparation table: dimensions: 4100 x 700 x 1000 mm 2/3 pipe finishing machine O25 (D=75 mm): dimensions: 6300 x 1000 x 1300 mm 3/3 receiving table: dimensions: 4100 x 600 x 1000 mm  ,please also have a look at the video of this machine weight approx.: 4,000 kg, Approx. Onsite Dimension. (l x w x h): 6,300 x 2,000 x 1,300 mm