For extruders 500 to 1500 kg/h Supporting structure made in sturdy steel with sides made in special alloy. Group of dandy rolls to guide the streams Lower roll in cemented steel Upper, pressing roll made in nitrated steel, pneumatically lfted Asynchrone drive with inverter Cutting unit with dual cutting edge Made in anti-wear steel Electrical control panel with general switch,service switch and amperometer Adjustable speed Rotor diam. 240 mm. N.28 teeth on rotor Counter-blade length 350 mm. 2 cutting edges, 11 kw drive Include n.1 extractor, User’s manual, CE compliance

AIR PELLETIZER FOR PVC AND COMPOUNDS for throughput 500 to 1500 kg/h connection flange built on Clients design made in steel heated by ceramic heaters, temperature probe and protection carter, stainless steel granulation chamber on horizontal axix, quick opening, knife-holder with fluctuating star to reduce knives consumption., self adjusting knives to nozzle by means of a spring which keeps knives pressed, with less wearing out and increased efficiency n.1x 3 kw motorwith extra strong bearing and long shaft, cutting die in anti-wear steel with number and Ø of holes bespoke to project. 1,5 kw blower, Venturi system, knife template, electric cabinet and touch screen control board with modem  ...

BUFFER SILO 15.000 lt. (or 8.000 - 12.000 - or bespoke), barrel Ø 2,2 mt. - height 3.0 mt., overall height 5,23 mt, made in electro-welded carbon steel sheet, sturdy supporting structure, internal rotor with spiral and agitator arms, inspection hatch on barrel wirh safety devices, bonfiglioli gearbox, power 3 kw electric motor, transmission with elastic coupling, finish painted externally with rustproofing and enamel, CE compliance + instruction manual, installed power : 3

MAGNETIC SEPARATORS, in form of overbelt plates,, grids, channels, stars, etc. ...

• больше информации

Fitted with a 12 mm grid N.2 outlets All parts in contact with material are on AISI304 stainless steel Classifying surface 1400×500 mm. Electric panel for start/stop Safety switches Height of granule outlet 650 mm.from floor ...

• больше информации

Including: Injector Hopper Pipe connection diam. 160 mm. Bends Clamps Cyclone Customized to your project ...

• больше информации

Hydraulic Gripper ...

• больше информации

CONVEYOR BELTS, with METAL DETECTORS or OVERBELT METAL SEPARATORS, top quality and sustainable prices, Size and characteristics bespoke to the project., Ask for more information ...

• больше информации

Goose neck shaped conveyor belt Blueprint 3.541 mm. on floor mm. 2.150 in horizontal + 1.350 mm. diagonal Angle 45° 1.166 mm discharging point Approx.450 mm working width Complete with transport paddles 1,5 kw gear motor Fitted with a 250 mm diam.magnetic drum at the end Discharging outlet on bottom for material Separate discharging outlet for extracted ferrous material, The machine is as new, 200 worked hours

QUICK WASHER for RIGID and SOFT PLASTICS, made in AISI304 stainless steel, low water consumption, can be used with hot water or mild detergents, for reground LDPE LLDPE HDPE film, rigid PE PP PVC PET PA ABS PS PC, 7,5 kw motor 400V 50/60Hz, inner auger 400 mm diam., length 3.000 mm., material and water are loaded from the bottom, material discharging is done through a draining auger from top, bearings are positioned outside the wet chamber, seals on the lower bearing to exclude any contact with water, auger speed is adjustable to change throughput rate 500 to 1.000 kg/h, throughput rate can be adjusted according to contamination and material, Low water consumption (depending on contamination ...