lathes used for sale

Key data: 350 mm, 650 mm, 25 1/min

well-preserved, used NEF 400 Siemens Sinumerik 840 D control system Year of construction 2007 Switch-on hours 16000 h incl. 3-jaw wedge bar chuck Röhm Spindle bore 79 mm Turret 8 positions Rapid traverse X-axis 20 m/min Rapid traverse Z-axis 24 m/min Drive power - spindle motor 11.5 kW Tailstock displacement 550 mm Pick-up cone in the tailstock quill MK4 Quill diameter 80 mm

turning diameter over bed: 500 mmturning diameter over slide rest: 300 mmturning length: 1000 mmturning diameter in the gap: 710 mmturning speeds: 36 - 1600 U/mincentre height: 250 mmspindle bore: 103 mmtailstock quill taper MT: 5 MKtailstock travel: 150 mmtailstock quill diameter: 75 mmtotal power requirement: 7,5 kWweight of the machine ca.: 2,75 tdimensions of the machine ca.: 2,5 x 1,1 x 1,4 mCenter lathe with- 3-jaw chuck F 315- Fixed tailstock top- Multifix holder- 2-axis digital display- Fixed Lynette 180 mm- Coolant system- rapid traverseThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

-Peak height 240mm -Peak width 1000mm -Control Siemens -Circular permes.about bed 490mm -Umlaufdurchmes.ü.Planschlitten 195mm -Crumpling 520mm -Spindeldurchmes.im in front. Bearing 100mm -Spindle bore 63mm -Torque 736Nm

turning diameter over bed: 360 mmturning diameter over slide rest: 220 mmturning length: 1000 mmturning diameter in the gap: 506 mmturning speeds: 45 - 1800 U/mincentre height: 180 mmspindle bore: 38 mmtailstock quill taper MT: 3 total power requirement: 2,4 kWweight of the machine ca.: 0,9 tdimensions of the machine ca.: 1,9 x 0,8 x 1,2 mCenter lathe with- 3-jaw chuck F 315- Fixed tailstock top- Multifix holder- 2-axis digital display- Fixed Lynette 180 mm- Coolant system- rapid traverseThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Ladies and gentlemen, below we offer the following machine for sale: from a tool making, single-layer run and very well maintained. Still under power. CNC lathe Voest - Alpin - Weipert WNE 490 X 1000, peak height 240mm, tip width 1000mm, control Siemens, circulating through mes.over bed 490mm, circulating permes.via plan slide 195mm, crimping 520mm, Spindeldurchmes.im front. Bearing 100mm, spindle bore 63mm, torque 736Nm.

turning diameter over bed: 320 mmturning diameter over slide rest: 200 mmturning length: 900 mmturning diameter in the gap: mmturning speeds: 75 - 2000 U/mincentre height: 160 mmspindle bore: 50 mmtailstock quill taper MT: 3 MKconnected load frequency: 230 Vtotal power requirement: 1,5 kWweight of the machine ca.: 0,29 tdimensions of the machine ca.: 2,0 x 0,8 x 1,56 mProfessional lathe3-jaw chuck4-jaw chuckfaceplatebezel fixedrunning bezelQuick-change steel holder with 4 cassettesHalogen machine lightChip tray, chip protection wallHardened and ground bed tracksComplete coolant systemfeed protectionmachine toolsThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Cam controlled multi spindle automatic lathe, used 6 main spindles, control: Siemens S5 PLC, electronical trip dog control type „Balluff gear box for thread milling (2 pieces) pick up for rear machining in pos. 6, work piece sorting shute, barloader: IEMCA-PRA 40/33 P -rack type- coolant pump, threading clutches, stock stand and reel, tooling: could be different like pictures partly revised

turning diameter over bed: 400 mmturning diameter over slide rest: 200 mmturning length: 1500 mmturning diameter in the gap: mmturning speeds: 28 - 1400 U/mincentre height: 200 mmspindle bore: 50 mmtotal power requirement: 10,4 kWweight of the machine ca.: 2,85 tdimensions of the machine ca.: 3,5 x 1,4 x 1,6 mCenter lathe- Rapid traverse- Faceplate 400mm- Multifix steel holder- Coolant system- Feed protection- chip trays- Chip protection wall- Emergency stop facility- Machine lightThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

8 main spindles, Chucker AFH130 for complete machining means front- and back side, Control Siemens Sinumerik 840DI, complete revising and new configuration of this machine in year 2010, loading arm, for loading and disloading, Workpiece turn around station in pos. 4 , position 4 with workpiece length control, CNC compound slide in pos. 5, coolant pump with magnet candle filter, tooling: could be different like pictures option: Ergomat TB42 fot cutting off for half finnishing with FMB-Turbo

turning diameter over bed: 500 mmturning diameter over slide rest: 250 mmturning length: 1200 mmturning diameter in the gap: mmturning speeds: 7,1 - 1400 U/mincentre height: 250 mmspindle bore: 49 mmtotal power requirement: 7,5 kWweight of the machine ca.: 3,9 tdimensions of the machine ca.: 2,85 x 1,3 x 1,6 mLead and feed spindle lathe- 3-jaw chuck 260mm- 4-fold steel holder- Coolant systemThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Key data: 490 mm, 515 mm

Machine Details Stock-No. 1105-04004 Type of machine CNC Turning- and Milling Center Make MORI SEIKI Type NL 1500 SY Year of manufacture 2005 Type of control CNC Storage location FRANCE Country of origin Japan Delivery time immediately Freight basis ex Warehouse Technical details turning diameter 490 mm turning length 515 mm control MSX-850 max. bar capacity 52 mm Travel -X Axis 280 mm Travel -Z Axis 490 mm max. speed main spindle 6000 min-1 spindle taper 1 A2-6 C - Axis 0.001° Spindle Bearing Diameter 110/75 mm No. of tools in turret 1 12 Shaft Cross Cut 25 x 25 mm Shank diameter 50 / 32 mm turret change time 0.25 s Max. Spindle Speed Driven Tools 6000 min-1 rapid power traverse in X-and Z direction 30 m/min Rapids C - Axes 400 min -1 drive capacity - spindle motor 18.5 kW power capacity - driven tools 5.5 kW swing diameter over face slide 278 mm great ...

turning diameter over bed: 250 mmturning diameter over slide rest: 130 mmturning length: 550 mmturning speeds: 50 - 2000 U/mincentre height: 125 mmspindle bore: 20 mmtailstock quill taper MT: 2 tailstock quill stroke: 60 mmmetric threading: 0,4 - 3,0 mmthread - inch: 10 - 44 TPIthread - module: 0,2 - 12,5 mmconnected load frequency: 230 Vtotal power requirement: 1,0 kWweight of the machine ca.: 0,12 tdimensions of the machine ca.: 1,09 x 0,59 x 0,45 mEquipped with- 20 mm spindle passage- adjustable guideways- Powerful 1.0 kW motor- continuously variable speedScope of delivery:- 3-jaw chuck 100 mm,- 4-jaw faceplate chuck 125mm- standing and rotating bezel- Splash guard- Feed protectionThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Inv. Num. : 7421 Type: SL 30 HE Producer: HAAS Created: 2001 Parameters: To GO Control system: HAAS Spindle bore: 65 mm Max. turning length: 660 mm Number of tools in the storage container: 12xVDI40 pieces Maximum turning diameter over bed: 533 mm Spindle speeds: 3400 1/min Maximum main spindle power: 22.4 kW Equipment: Bake Tool Holder High-pressure cooling Tool Probe

turning diameter over bed: 470 mmturning diameter over slide rest: 300 mmturning length: 1000 mmspindle bore: 58 mmturning speeds: 20-2000 U/mintotal power requirement: 5,5 kWweight of the machine ca.: 1800 tdimensions of the machine ca.: mThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Inv. Num. : 7067 Type: GA-2600 Producer: Goodway Created: 2005 Parameters: Maximum turning diameter: 350 mm Max. turning length: 606 mm Maximum main spindle power: 15 kW Maximum spindle speed: 4000 1/min Spindle bore: 76 mm Max. rod diameter: 66 mm Clamping diameter: 254 mm Length: 2445 mm Width: 1630 mm Height: 1890 mm Weight: 4000 kg

turning diameter over bed: 400 mmturning diameter over slide rest: 220 mmturning length: 1000 mmturning diameter in the gap: mmturning speeds: 31,5 - 1400 U/mincentre height: 205 mmspindle bore: 50 mmtotal power requirement: 5,0 kWweight of the machine ca.: 1,4 tdimensions of the machine ca.: 2,5 x 1,2 x 1,7 mCenter lathe- 3-jaw chuck 210mm- Multifix steel holder- Coolant pump- Chip protection wall- chip tray- Machine lightThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Inv. Num. : 7432 Type: SW 32 Producer: Goodway Created: 2017 Parameters: Side length: 315 mm Max. turning diameter: 32 mm Weight: 3200 kg

turning diameter over bed: 410 mmturning diameter over slide rest: 210 mmturning length: 1500 mmturning diameter in the gap: mmturning speeds: 11 - 2240 U/mincentre height: 205 mmspindle bore: 80 mmtotal power requirement: 7,5 kWweight of the machine ca.: 2,1 tdimensions of the machine ca.: 3,3 x 1,4 x 1,8 mCenter Lathe- Fagor digital display- Röhm 3-jaw chuck 250mm- Multifix steel holder with 4 cassettes- Coolant system- Machine light- Feed protection- Chip protection wall- chip tray- Emergency stop facilityThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Inv. Num. : 7447 Type: NT 2000 SY Producer: YCM Created: 2015 Parameters: Control System: FANUC TXP-200FB Maximum turning diameter: 350 mm Max. turning length: 519 mm Spindle diameter: 52 mm Number of tools: 12 pieces Axis Y: 50 mm Weight: 7600 kg Equipment: Technical Documentation Conveyor Shovel Spacesaver SS2220 Bar Feeder Tool Probe BMT65 Brackets (External/Front/Internal/2pcs Powered) High Pressure Pump 2x universal chuck for both spindles 3x collet clamp for both spindles Preparation for the connection of the mist collector

turning diameter over bed: 660 mmturning diameter over slide rest: 420 mmturning length: 2000 mmturning diameter in the gap: 840 mmturning speeds: 36 - 1600 U/mincentre height: 330 mmspindle bore: 103 mmtailstock quill taper MT: 5 MKtailstock travel: 150 mmtailstock quill diameter: 75 mmtotal power requirement: 11 kWweight of the machine ca.: 3,2 tdimensions of the machine ca.: 3,6 x 1,1 x 1,45 mCenter lathe with- 3-jaw chuck F 315- Fixed tailstock top- Multifix holder- 2-axis digital display- Fixed Lynette 180 mm- Coolant system- rapid traverseThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Inv. Num. : 7399 Type: PUMA 3100 Producer: DOOSAN Created: 2015 Parameters: Control system: FANUC Max. turning length: 760 mm Max. turning diameter: 525 mm Maximum travel length in the X-axis: 293 mm Maximum feed rate in the Z-axis: 830 mm Spindle speeds: 2800 1/min Maximum main spindle power: 22 kW Number of tools: 10 pieces Length: 4095 mm Width: 1978 mm Height: 2010 mm Weight: 5850 kg Equipment: Conveyor Programmable tailstock/quill 3-jaw chuck 2022/8: Replacement of bearings in the spindle

turning diameter over bed: 360 mmturning diameter over slide rest: 220 mmturning length: 1000 mmturning diameter in the gap: 380 mmturning speeds: 70 - 2000 U/mincentre height: 180 mmspindle bore: 50 mmtailstock quill taper MT: 3 MKconnected load frequency: 230 Vtotal power requirement: 1,8 kWweight of the machine ca.: 0.65 tdimensions of the machine ca.: 2,0 x 0,8 x 1,56 m3-axis digital display3-jaw chuck 200 mm.4-jaw chuck 200 mm.Faceplate 320mmbezel fixedrunning bezel4-fold steel holder.Halogen machine lightmachine lightfoot brakeremovable chip tray, chip protection wallHardened and ground bed tracksComplete coolant systemlining protectionmachine toolsThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Inv. Num. : 7400 Type: GT 2100 Producer: DOOSAN Created: 2013 Parameters: Control system: FANUC Maximum turning length: 562 mm Max. turning diameter: 390 mm Maximum turning diameter over bed: 600 mm Maximum travel length in the X-axis: 230 mm Maximum feed rate in the Z-axis: 580 mm Maximum main spindle power: 15 kW Maximum spindle speed: 4500 1/min Number of tools: 10 pieces Length: 3890 mm Width: 1628 mm Height: 1700 mm Weight: 3500 kg Equipment: Technical Documentation Conveyor Shovel Collets Bake Knife Collet head Universal three-jaw head Cutter head with 10 positions Programmable tip/spring 2023/3: Replacement of bearings in the spindle

turning diameter over bed: 560 mmturning diameter over slide rest: 355 mmturning length: 2000 mmturning diameter in the gap: 790 mmturning speeds: 20 - 1800 U/mincentre height: 380 mmspindle bore: 80 mmtailstock quill taper MT: 2,8 MKtailstock travel: 150 mmtailstock quill diameter: 75 mmtotal power requirement: 5,5 kWweight of the machine ca.: 3,4 tdimensions of the machine ca.: 3,5 x 1,15 x 1,3 m• 80 mm spindle passage• Gears hardened and ground• manual central lubrication• adjustable main spindle bearings• Overload clutch in the lock case• bed bridge• incl. 3 - axis digital displayThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Inv. Num. : 7112 Type: LP 130 CNC ES Producer: Laschet Partner Created: 1997 Parameters: Control system: SIEMENS SINUMERIK Maximum travel length in the X-axis: 300 mm Max. travel length of the Z-axis: 280 mm Maximum main spindle power: 25 kW Maximum spindle speed: 5700 1/min Spindle bore: 80 mm Length: 2800 mm Width: 1450 mm Height: 2000 mm Weight: 4200 kg Equipment: Spares Bar feeder Complete set of collets

turning diameter over bed: 400 mmturning diameter over slide rest: 264 mmturning length: 1000 mmturning diameter in the gap: 550 mmturning speeds: 44 - 2000 U/mincentre height: 200 mmspindle bore: 52 mmtailstock quill taper MT: 4 MKconnected load frequency: 400 Vtotal power requirement: 1,5 / 2,4 kWweight of the machine ca.: 0,9 tdimensions of the machine ca.: 1,9 x 0,8 x 1,56 m3-axis digital display3-jaw chuck 200 mm.4-jaw chuck 200 mm.Faceplate 320mmbezel fixedrunning bezel4-fold steel holder.Halogen machine lightmachine lightfoot brakeremovable chip tray, chip protection wallHardened and ground bed tracksComplete coolant systemlining protectionmachine toolsThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Inv. Num. : 7115 Type: LP 100 CNC Producer: Laschet Partner Created: 1999 Parameters: Control System: FANUC Series 0-T Maximum travel length in the X-axis: 300 mm Maximum feed rate in the Z-axis: 280 mm Spindle bore: 300 mm Length: 2800 mm Width: 1450 mm Height: 2000 mm Weight: 3200 kg Equipment: MRW Robopot Feeder

turning diameter over bed: 250 mmturning diameter over slide rest: 145 mmturning length: 550 mmturning speeds: 50 - 2000 U/mincentre height: 125 mmspindle bore: 26 mmtailstock quill taper MT: 2 MKconnected load frequency: 230 Vtotal power requirement: 0,75 kWweight of the machine ca.: 0,12 tdimensions of the machine ca.: 1,3 x 0,65 x 0,6 m3-axis LCD digital display systemlongitudinal feed.3-jaw chuck 125 mm.4-way steel holder.chip tray, bulkheadHardened bed tracks.Emergency stop switch.lining protectionTool box, instruction manual.The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Inv. Num. : 4619 Type: GR 300C Producer: MAHO Graciano Generated: 1990-1993 Parameters: Control system: CNC 432 Philips Maximum turning length (travel in the Z axis): 620 mm Maximum turning diameter over bed: 370 mm Maximum turning diameter over support: 320 mm Maximum travel length in the X-axis: 250 mm Minimum main spindle speed: 1000 rpm Maximum main spindle speed: 5000 rpm Number of turret heads: 12 pieces Equipment: Tailstock

turning diameter over bed: 250 mmturning diameter over slide rest: 145 mmturning length: 550 mmturning speeds: 50 - 2000 U/mincentre height: 125 mmspindle bore: 26 mmtailstock quill taper MT: 2 MKconnected load frequency: 230 Vbore capacity in steel: 16 mmthroat: 169 mmquill stroke: 50 mmturning speed range - drilling: 50 - 2250 U/minspindle drive: 0,5 kWtotal power requirement: 0,75 kWweight of the machine ca.: 0,175 tdimensions of the machine ca.: 1,3 x 0,65 x 1,3 m3-axis LCD digital display systemlongitudinal feed.3-jaw chuck 125 mm.4-way steel holder.chip tray, bulkheadHardened bed tracks.Emergency stop switch.lining protectionTool box, instruction manual.The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.