machines de travail des métaux / fraiseuses / Fraiseuses universelles à console
Fabricant: DMG MORI
Modèle:DMP 70
Type de machine: Fraiseuses universelles à console
Numéro de l'article: 168153711
Quantité: 1
Date: 11.12.2025
Emplacement:
Allemagne
Prix:
Seller-item-No.:051428
| General | |
| High dynamic Vertical Drill-Tap centre with best milling performance; Control: 3D-control Siemens 840D sl Operate | |
| Working area 1 | |
| Longitudinal | 700 mm |
| Cross | 420 mm |
| Vertical | 380 mm |
| Technical Data | |
| Feed rate longitudinal/transverse/vertical | 60000/60000/60000 mm/min |
| Rapid traverse longitudinal/transverse/vertical | 60/60/60 m/min |
| Main drive | Drive power (100% DC) 6 kW |
| Drive power (40% DC) 8,5 kW | |
| Torque (100% DC) 41 Nm | |
| Clamping System ISO 7388-3 - JD30 | |
| Spindle taper BT 30 | |
| Speed range 20 - 10000 rpm | |
| Torque (40% DC) 48 Nm | |
| Integrated swivel rotary table simultaneous | Integated swivel rotary table 5-Axis simultaneous mode! Torque drives incl. direct measuring in A- and C-Axis Swivel range A-Axis -120 / + 100 degrees Max. load C-axis 100kg Table diameter C-Axis d290mm Inclusive Software package Sinumerik Mdynamics 5-ax |
| Rotary joint, 4 channels | Rotary joint for integrated swivel rotary table with torque drives 4- channels, in Standard 2x for air, 2x for oil Including fix plate and fast coupling at machine rear side |
| Clamping pneumatic, one circuit | Clamping pneumatic 1-circuit Including 2x 3/2 way valve |
| Tool magazine 25 places | Tool magazine 25 places (suitable for inclusion in the tool spindle) Chip-to-chip time 1.6 sec |
| Production package band filter ICS 40bar | Paper band filter ICS 40bar includes: Paper band filter 40bar/ 23l/min Additional tank 600l Chip conveyor useable for fine chips (self cleaning slotted filter) Discharge height: 600mm; Tank volume 200l Flushing in working room Spray gun for swarf removal |
| Air blast through spindle centre | Air blast through spindle center via M-Command; maintained air with small Oil portion Due to needed lead through in main spindle only with swarf removal package ICS possible! |
| Preparation 3D Quickset | Machine preparation for use of the 3D quickSET Toolkit. included is the Softwareoption for 3D quickSET for one machine. 5 axis machine configurations (only with option touch probe) |
| Signal lamp 4-colour | Signal lamp, 4 colours |
| DMG MORI Interface PROFIBUS Right | DMG MORI Interface PROFIBUS loading door at right machine side PROFIBUS communication between robot and machine for loading cycle 2 channel safety circuits Only in combination with an additional clamping method option!. |
| Operation mode 4 | Operation mode 4 Process monitoring in the production Manual intervention with open doors of machining area. Release after check list has been filled in. |
| Tropical package | Package for tropical climate for ambient temperature max. 50°Celsius: includes active cooling for electrical cabinet, active cooling main spindle drive / motor spindle |
| Special equipment | RMS-Sensor |
| Workpiece loading & unloading system WH 3 CELL | Workpiece loading & unloading system WH 3 CELL with 6-axis industrial robots and workpiece carrier storing system (paternoster); maximum possible workpiece weight of 3 kg, maximum workpiece size 100 x 100 x 50 mm Robot FANUC LR Mate 200 iD/7L PROFIBUS in |
| WH 3 CELL Integration kit for DMP 35/70 | WH 3 CELL Integration kit for DMP 35/70 Machine-specific adaptation for the protective housing on one DMP 35/70 |
| Dual gripper PGN 80 (without gripper fingers) | Dual gripper Type Schunk PGN 80 with 8 mm travel per jaw (gripper fingers not included!) |
| Gripper system Schunk PGN-plus 80 | Gripping device Schunk PGN-plus 80 |
| 2023 | DMG MORI | DMP-70 | |
| DMG MORI | DMP 35 | ||
| DMG MORI | NLX 2500|700 | ||
| 2014 | DMG MORI | Milltap 700 | 38900 EUR |
| DMG MORI | CTX 2500|700 | ||
| 2016 | DMG MORI | Milltap 700 | 41900 EUR |
| DMG MORI | CTX 2500|700 | ||
| 2023 | DMG MORI | NLX2500/700 | |
| 2013 | DMG MORI | Milltap 700 | |
| DMG MORI | NLX 2500|700 |
| 2015 | DMG MORI | Milltap 700 | 90000 EUR | [Mar 2017] |
| 2016 | DMG MORI | Milltap 700 | 54900 EUR | [Jul 2024] |
| 2022 | DMG MORI | CMX 70U | 155000 EUR | [Oct 2024] |
