We use cookies to optimize our website for you and to be able to continuously improve it. By continuing to browse the site you are agreeing to our use of cookies.
Disagree
Manufacturer:
(Category: 203)
used
Inv. Num. : 6696 Type: Profiset 60 Producer: SCM Created: 2018 Parameters: Number of spindles: 5 Vacuum belt width: 25-230 mm Working height: 6-120 mm Max. speed: 6000 1/min Equipment: Swivel head
new
Working width: 318 / 295 mmWorking height: 170 mmMotor output: 2,25 kWLength of the planing table: 1300 mmNumber of knives: 3 St.Feed speed: 5,3 m/min.Dust suction hood: 100 mmconnected load frequency: 400 Vmachine weight ab.: 160 kgDimensions (L/W/H): 1150 x 530 x 930 mmThe planer and thicknesser is delivered almost fully assembled.For thickness planing, the same connection is used for suction as for surface planingused. However, this is placed upwards over the storage table. The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
4 CUTTER HEADS, MAX. DIMENSIONS OF THE WORK PIECE: 180/120 MM, MIN. DIMENSINS OF FINISHED WORK PIECE: 16/7 MM, SPINDLE SPEED: 6000 RPM, OPERATION HOURS: 30 HOURS ONLY!
used
x-travel: 11000 mmy-travel: 2.500 mmworkpiece height: mmtable width: mmtable length: mmweight of the machine ca.: tdimensions of the machine ca.: mThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
used
Four-sided planer REX HOMS-410 – made in Germany – for wet wood TECHNICAL PARAMETERS: planing width max. 410 mm planing height on both sides 200 mm planing height on four sides 200 mm spindle diameter 40 mm shaft motor power 2 x 11 kW spindle motor power 2 x 5.5 kW feed speed infinitely adjustable feed speed adjustable on the inverter three upper pulling rollers three lower pulling rollers two auxiliary rollers in the table top brake minimum workpiece length 450 mm dimensions of the machine (length/width/height) 250 / 220 / 180 cm weight ~ 3500 kg
used
x-travel: 8000 mmy-travel: 2.500 mmworkpiece height: 2.360 mmtable width: 2.240 mmtable length: 10.100 mmweight of the machine ca.: tdimensions of the machine ca.: 20,0 x 8,5 x 5,2 mThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
used
Weibert WJ-FS32-W7 Dressing thickness planer 3-reversible planer knife shaft HSS Motor 3kW 400V 50Hz Passage height: 4-225mm Numerical display of the planing height Planed dressing and thicknessing tables G&2972-2036-W7
used
Working width: 410 mmLength of the planing table: 2.200 mmNumber of knives: 5 St.Motor output: 5 kWweight of the machine ca.: ca. 411 kg: Tersa : Ja Dust suction hood: 120 mmturning speeds: 5.000 U/minThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
used
The machine contains the components from the large-scale series of the powerful WEINIG class Working width 20 – 260 mm / carpentry version Working height 8 – 160 mm 5 working spindles DM 40 mm Long inlet work table - 2000 mm 5 working spindles, bottom 5.5 kW, left + right 7.5 kW, top 7.5 kW, plaster bottom 11 kW Pneum. Pressure of the feed rollers Cardan feed infinitely variable 5 – 24 m/min. ATS system: Up to 98 workpiece dimensions can be programmed and called up at the touch of a button Left and upper spindle drive auto. in position Machine in CE design Built in 1998 Without editing tools
used
Working width: 410 mmNumber of knives: 2 St.Motor output: 4 kW: Streifenhobelmesser turning speeds: 4.600 U/min: Nein The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
used
Specifications: -working width 230 mm -feeding speed 5-25 m/min. -working height 130 mm -number of spindles 9 -configuration down-right-left-right-up-down-left-up-down -total power about 45 kW -
used
Working width: 530 mmLength of the planing table: 2.900 mmNumber of knives: 4 St.Motor output: 4 kWweight of the machine ca.: 850 kg: Tersa : Ja The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
used
Part Number 6368 TECHNICAL DATA - max width of the workpiece 230mm - max height of the workpiece 130mm 7 spindles: 1) horizontal bottom 230mm 5,5kW 2) vertical right 130mm 5,5kW 3) vertical left 130mm 5.5kW 4) horizontal top 230mm 7,5kW 5) horizontal upper 230mm 11kW 6) horizontal bottom 230mm 18,5kW 7) universal 230mm adjustable at 360 degrees 5.5kW - all spindles adjustable up/down, right/left - all spindles equipped with an electric brake - spindle diameter 40mm - spindles 4 and 5 electrically adjustable up/down - from above 8 metal pulling introductory shafts, swivel including 2 double - from above 4 pulling rollers, rubber - pressure from above 2pcs - from the bottom of the ratchet - from the bottom from the side 3 clamps - from below 2 metal rollers, smooth, pulling - from the bottom 2 double rollers, pulling, rubber - pneumatically pressed shafts ...
used
Working width: 520 mmWorking height: 240 mmMotor output: 7 kWNumber of knives: 4 St.Feed speed: 5/8/12/16 m/min.weight of the machine ca.: ca. 500 kg: Tersa : Ja Dust suction hood: 120 mmThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
used
CATALOG NO. 7220 TECHNICAL DATA - min – max width of the processed element 20 – 230mm - min – max height of the processed element 8 – 160mm 7 spindles: 1) horizontal bottom 230mm 5.5kW 2) vertical right 160mm 5.5kW 3) vertical left 160mm 5.5kW 4) vertical right 160mm 5.5kW 5) vertical left 160mm 5.5kW 6) horizontal top 230mm 7.5kW 7) horizontal bottom 230mm 7.5kW - all spindles adjustable up/down, right/left - spindle diameter 40mm - spindle speed 6000 rpm in advance: - 10 pulling, toothed and metal input rollers, including 2 double rollers - 3 side pressures from down: - pressure from the side at the insertion - input shaft, toothed, pulling, turning in the lower tabletop - 2 pressure points from the side - grooved top - drawing roller, metal, grooved - drawing roller, metal, smooth - pneumatically adjustable rollers - length of the introductory tab ...
used
Working width: 510 mmLength of the planing table: 2.250 mmNumber of knives: 4 St.Motor output: 5,5 kWDimensions (L/W/H): 2.427 x 1.340 x 890 mm: Ja weight: 750 kgDust suction hood: 140 mm: Keilleistenmesser The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
used
CATALOG NUMBER 6679 TECHNICAL DATA - max width of the workpiece 250mm - max height of the workpiece 170mm 6 spindles: 1) horizontal lower 250mm 5.5kW 2) vertical right 170mm 5.5kW 3) vertical left 170mm 5.5kW 4) horizontal, upper 250mm 7.5kW 5) horizontal lower 250mm 7.5kW 6) universal 250mm, adjustable at an angle of 360 ° 5.5kW - 6 electrically adjustable spindle up / down - all adjustable spindles up / down, right / left - diameter of the spindles 40mm - 6 introductory pulling rollers, toothed, including 2 double ones - 6 rollers leading out, pulling, rubber, smooth, including 2 double - 2 clamps from above - from the bottom, a roller introducing toothed, pulling, torsion in the table before the first spindle - at the bottom, 2 pulling rollers, metal, smooth - 4 side clamps at the bottom - feed on cardan shafts - pneumatically pressed rollers - smooth regulati ...
used
Number of boring spindles: 5 St.Working width: 230 mmWorking height: 120 mmLength of the planing table: 2.000 mmFeed motor: 2,2 kWFeed speed: 5-24 m/min.weight of the machine ca.: 3.000 kgturning speeds: 6.000 U/minspindle diameter: 40 mm: Ja The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
used
Part Number 6338 TECHNICAL DATA - max width of the workpiece 230mm - max height of the workpiece 160mm 7 spindles: 1) horizontal bottom 230mm 5,5kW 2) vertical right 160mm 5,5kW 3) vertical left 160mm 5.5kW 4) horizontal top 230mm 7,5kW 5) horizontal upper 230mm 7,5kW 6) horizontal bottom 230mm 7,5kW 7) universal 360° 230mm 7,5kW - all spindles adjustable up/down, right/left - spindle diameter 40mm - all spindles equipped with a brake - spindle speed 6000rpm in advance: - 6 pulling, toothed, metal introductory shafts, including 2 double - 4 pulling shafts, rubber including 1 double - 3 clamps on the lead bottom: - pressure from the side on the inlet - introductory shaft, toothed, pulling, swivel in the lower table top - 3 pull rollers, metal, smooth - pneumatically adjustable shafts - length of the introductory table top 1190mm - central lubricati ...
used
x-travel: NA mmy-travel: NA mmworkpiece height: mmstroke length max.: 450 mmtable length: 450 mmtable width: 350 mmtotal power requirement: 1,7 kWweight of the machine ca.: tdimensions of the machine ca.: mShaper, horizontal,mechanic,vice hydraulic The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
used
Key data: 410 mm, 2850 mm, 4 St.
Specifications/Equipment: Planing width 410 mm Chip removal max. 8 mm Table length 2,850 mm TERSA knife shaft with 4 blades Knife shaft speed 5000 rpm SUVAmatic planer shaft protection cover electr. Feed table height adjustment Dispensing table with hollow and pointed joint adjustment Stop can be tilted up to 45° Motor power 4 kW Suction nozzle Ø 160 mm Space requirement 2,850 x 1,950 x 1,027 mm Weight approx. 870 kg All information is subject to the actual equipment
used
Number of spindles: 6 St.Working width: 240 mmWorking height: 120 mmDimensions (L/W/H): 4900 x 1700 x 1700 mmweight of the machine ca.: 3500 kgControl: SCM SUPERSET NTE 31 PLUS automatic profile milling machine with 6 shafts14 axis control with touch screen - WINDOW VERSIONMachine with 6 spindlesSpindle speed 8,300 rpmWorking width 240 mm, working height 120 mmElectronic horizontal and vertical positioning of the spindlesGlazing bead cuttingTouchscreen controlsDetailed technical description, seeadjacent PDF documents.Suction nozzle diameter:1. Spindle down: 120mm2nd spindle right: 120 mm3. Left spindle: 120 mm4. Spindle top: 150mm5. Spindle top: 150mm6. Spindle below: 120mmOption: workpiece return to the operatorImages are from our archive of a machine of the same model.(Technical information according to the manufacturer - without guarantee!)The data for this ad was created with ModulM ...
used
Key data: 505 mm, 250 mm, 5 kW
Specifications/Equipment: Planing width approx. 505 mm Planing height max 250 mm Chip removal max. 8 mm Table length 1,110 mm Electr. Thickness table height adjustment with digital display Thicknessing table guided on 4 spindles Feed speed 7/14 m/min One rubberized feed roller each in the inlet and outlet TERSA knife shaft with 4 blades Knife shaft speed 5000 rpm Motor power 5.5 kW Suction nozzle Ø 160 mm Dimensions: 1,200 x 950 x 1,050 mm Weight approx. 600 kg All information is subject to the actual equipment
new
Working width: 630 mmWorking height: 3-310 mmMotor output: 7,5 kWNumber of knives: 4-TERSA St.Feed speed: 6-20 m/min.Vertikal stroke: elektrisch FIMAL thickness planer type SP 63 A-----------------------------------------------------NEW MACHINE Partnership EditionTechnical specifications:-----------------------------------------------------Wo rking width: 630 mm4-knife cutterblock system TERSA, d=120mm: 4,800 rpmmax. chip removal planer according to CE: 8 mmmin./max. Thickness passage: 3/310 mmMinimum workpiece length: 250 mmFeed speed: infinitely variable 6 - 20 m/min.Motor 380 Volt / 50 Hz.: 7.5 kW withmanual star-delta switchSound level according to EN 27960: 86 - 90 dB(A)basic equipment:Thicknessing table adjustment via 4 trapezoidal thread spindlesElectromotive thicknessing table lift with electronicpositioning deviceElectronics according to CE standard Magnetic brakecircuit breaker ...
used
Technical data/equipment: - Working width 530 mm - Strip knife shaft, 4 knives - Connection 12A, 5.6 kW, 380 V, 50 Hz - Vibration protection planer shaft cover - electr. Table height adjustment - Shaft speed 5,000 rpm
used
Number of spindles: 6 St.Working width: 230 mmWorking height: 120 mmLength of the planing table: 2500 mmFeed motor: 4 kWFeed speed: 5-30 m/min.Weinig Powermat 400 with HSK/Powerlock, axial/radial CNC controlled------------------------------------------------------------ -----------Short summary:-------------------------------------------------------------- ---------6 spindles with 8,000 rpm5 x HSK/PowerlockAxial and radial CNC adjustment of the spindles via controlCNC - controlled adjustment and positioning of the feedDetailed description:---------------------------------------------------------- -------------Technical specifications:Working width: 20-230 mmWorking height: 8-120 mmNumber of spindles: 61. Tool holder - below------------------------------------------------Motor with brake: 5.5 kWSpindle diameter: 40mmSpeed: 6,000 rpmTool flight circle: 93 - 160 mmAxial adjustment range: 5 ...
used
Motor power 1.25 kW Power consumption 1.8 kW Shaft speed 6700 rpm Weight 93 kg Connection: 400 V / 50 Hz with integrated filter bag for self-suction
used
Number of spindles: 6 St.Working width: 230 mmWorking height: 120 mmLength of the planing table: 2500 mmfeed: 5-25 m/minCASOLIN MEGA 230/6 four-side planer--------------------------------------------------------Machine still in use to visit!6 spindles, with touchscreen controls.Width and height controlled.Spindle arrangement:1. Spindle: below, 40 mm diameter, 6,000 rpm, 5.5 kW2nd spindle: right hand, 40 mm diameter, 6,000 rpm, 11 kW together with3. Spindle: left, 40 mm diameter, 6,000 rpm4. Spindle: top, 40 mm diameter, 6,000 rpm, 7.5 kW5. Spindle: bottom, 40 mm diameter, 8,000 rpm, 5.5 kW6. Spindle: top, 40 mm diameter, 8,000 rpm, 5.5 kWMachine without machining tools.The additional screen on the front of the machine is not included in the scope of delivery (belongs to the window system).(technical information according to the manufacturer - without guarantee!)The data for this ad was c ...
used
Technical data (subject to change) Working width approx. 500 mm Chip depth as well as hollow and pointed joint indication Speed approx. 5,000 rpm Swivelling dressing stop Brake via foot pedal Weight approx. 950 kg
used
working length: 2000 mmWorking width: 250 mmWorking height: 970 mmWeinig pressure conveying system DEF 25 to the operator in workingheight for UnicontrolLength 2000 mmDepth 1800 mmBrand width 250 mmRear roller conveyor not driven 2500 mmRoll width 250 mm(technical details according to manufacturer - without guarantee.)The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.