voest alpine steinel used for sale

Description: Point width approx. 1500 mm , Turning diameter over bed approx. 940 mm , Turning diameter above support approx. 740 mm , Rod clearance approx. 200 mm Fabrication number 1-206/59 , Power 30 kW , Voltage 3 x 500 V Nominal current 55 A Frequency 50 Hz Control SIEMENS Sinumerik The machine was modernized in 2001 by the Stork company Approx. Onsite Dimension. (l x w x h): 4,500 x 2,200 x 1,950 mm, weight approx.: 4,500 kg

Key data: 120 mm, 60 mm, 1000 mm

Voest lathe in very good condition. Enormous amount of spare parts and additional parts included. Delivery possible immediately.

Screen surface: 1000 x 3000 mm, semi mobile steel structure with discharge chutes

Voest DA210 - 210/48/1500 universal lathe Centre distance: 1500 mm Tip height: 210 mm Turning diameter over bed: 430 mm Swing over carriage: 280 mm Quill recording: MK4 Spindle bore: 48 mm Bed width: 330 mm Speeds: 12 Speed range: 21-1500 rpm Feed speed: 0,072-4.04 mm Metric threads: 0.5-28 mm Inch thread: 1-56 tpi Motor power: 3 kW Voltage: 400V Dimensions WxHxD: approx. 2700 x 1400 x 800 mm Weight: 1500 kg Facilities: 4 - jaw Chuck, tracking grains u.m..

-Peak height 240mm -Peak width 1000mm -Control Siemens -Circular permes.about bed 490mm -Umlaufdurchmes.ü.Planschlitten 195mm -Crumpling 520mm -Spindeldurchmes.im in front. Bearing 100mm -Spindle bore 63mm -Torque 736Nm

Ladies and gentlemen, below we offer the following machine for sale: from a tool making, single-layer run and very well maintained. Still under power. CNC lathe Voest - Alpin - Weipert WNE 490 X 1000, peak height 240mm, tip width 1000mm, control Siemens, circulating through mes.over bed 490mm, circulating permes.via plan slide 195mm, crimping 520mm, Spindeldurchmes.im front. Bearing 100mm, spindle bore 63mm, torque 736Nm.

turning diameter: 570 mm turning length: 2000 mm control: centre height: 280 mm turning diameter over slide rest: 340 mm bed width: 350 mm spindle diameter: 100 mm spindle hollow: 63 mm transmission ratio: 2 spindle turning speed range: 1-2500 U/min quill stroke: 160 mm total power requirement: 15 kW weight of the machine ca.: 3,15 t dimensions of the machine ca.: 2,75x1,65x1,75 m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

turning diameter: 570 mm turning length: 2000 mm control: Siemens Sinumeric steady: chip conveyor: turning dia. in gap: 600 mm turning diameter over slide: 340 mm spindle bore: 63 mm Tool changer: total power requirement: 22 kW weight of the machine ca.: 4,5 t dimensions of the machine ca.: 3,5x1,5x1,5 m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Key data: 550

Center height: 550 mm Center distance: 2500 mm Spindle bore: 128 mm Workload 4.500 Kg Flying in chuck 1600 Kg Swing over bed Ø:        1.100mm Swing over cross slide Ø:780mm DBC Turning Length:      2.500mm Spindle bore:            128mm Spindle power:           37kW Bed width:               600mm Tailstock spindle Ø:     125Ø Stroke pinole:           270mm Spindle taper:           6Mk Speeds / ranges:         900Rpm Length:                  4.800 mm  Width:                   2.200 mm  Height:          &nb ...

Center height: 550 mm Center distance: 3000 mm Spindle bore: 128 mm Swing over bed Ø:        1.110mm Swing over cross slide Ø:775mm DBC Turning Length:      3.000mm Spindle bore:            128mm Spindle power:           30kW Bed width:               600mm Tailstock spindle Ø:     125Ø Spindle taper:           6Mk Speeds / ranges:         1120Rpm Length:                  4.500 mm  Width:                   2.000 mm  Height:                  2.000 mm  Weight:                  ...

Universal radial drilling machine make VOEST type AB 32Year of construction 1976Max. Drilling capacity ST: 50:32 mmMax. Drilling capacity: GG 20:40 mmDrilling ST / GG: 50/60 mmDrilling depth: 180 mmSpindle mount: MK 4Height adjustment of the boom: 610 mmProjection of the jib: 1000 mmTable surface: 1120 x 800 mm8 spindle speeds: 20 -3 000 rpm.3 automatic feeds: 0.05 / 0.1 / 0.2 mm / revDrive power: 1.5 kWWeight with base "940 kgWith- 3 automatic feeds- mot. boom stroke- Swing arm 360 °- Drilling head swiveling + 90 ° to -90 ° in the verticalxa0xa0 all 15 ° indexable, swiveling, adjustable and rotatablexa0xa0 (see brochure)- Cooling deviceused, in good conditionPrice on request.Delivery: ex warehouse or location free loading truck.Payment: net at takeover or by appointment.Technical data are not binding. Errors excepted.We would be pleased, if you like our offer and are always availabl ...

Hydraulic sheet metal shears make VOEST-ALPINE type BTHS 8 x 3150Fabr. -No: MBO-565Technical specifications:max.cutting length: 3150 mmmax.sheet thickness: 8.0 mmThroat: 300 mmInfinitely variable cutting length adjustment: 500 - 3150 mmStop adjustment range: 0 - 1000 mmWeight about 10.2 tDimensions approx: 3500 x 2300 x 1900 mmwith- motorized backgaugeused, in very good conditionPrice on request.Delivery: ex warehouse or location free loading truck.Payment: net at takeover or by appointment.Technical data are not binding. Errors excepted.We would be pleased, if you like our offer and are always available for your queries.Best regardsM. WaldeckWAHO Machine Tools

Four - jaws flat disc with individually adjustable clamping jaws. Diameter: 400 mm. High, without jaws: 100 mm, with jaws: 155 mm. Through hole: 90 mm. Chuck flange: DIN 55027, Size: 6 with 4 bolts, 21.5 mm with M 12 nuts and clamping wrench Good cleaned and ready for use condition. Weight: approx. 45 kg. Shipping with forwarding possible. The part was mounted on a VOEST lathe, type: DA 210 - 250. The Planchine can be visited in consultation and is immediately available. Please also note my other entries.

turning diameter over bed: 330 mm turning diameter over slide rest: 190 mm centre distance: 650 mm total power requirement: kW weight of the machine ca.: t dimensions of the machine ca.: m turning length: mm 4-jaw chuck Multifix tool holder device tail stock coolant device Technische Daten / technical details: Spitzenweite / center to center 650 mm Dreh-Ø über Bett / turning diameter over bed 330 mm Dreh-Ø über Schlitten / turning diameter over sledge 190 mm Spindelbohrung / spindle hole 36 mm Drehzahlbereich / spindle speed 30-2500 UpM /rpm Antriebsleistung / drive capacity 2,2 kW Gewicht der Maschine ca. / weight ca. 600 kg Technische Daten, Zubehör und Beschreibung der Maschine sind unverbindlich - Technical data, accessories and description of the machine are not binding. The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

turning diameter over bed: 330 mm turning diameter over slide rest: 190 mm centre distance: 650 mm total power requirement: kW weight of the machine ca.: t dimensions of the machine ca.: m turning length: mm 3-jaw chuck Multifix tool holder device tail stock coolant device Technische Daten / technical details: Spitzenweite / center to center 650 mm Dreh-Ø über Bett / turning diameter over bed 330 mm Dreh-Ø über Schlitten / turning diameter over sledge 190 mm Spindelbohrung / spindle hole 36 mm Drehzahlbereich / spindle speed 30-2500 UpM /rpm Antriebsleistung / drive capacity 2,2 kW Gewicht der Maschine ca. / weight ca. 600 kg Technische Daten, Zubehör und Beschreibung der Maschine sind unverbindlich - Technical data, accessories and description of the machine are not binding. The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Impact Mill Voestalpine Brand: voestalpine Inlet opening: 900 x 680 mm. Drive: 55 kW electric motor.

Voest DA180-52-800 - Universal lathe - the machine is completely revamped and as good as new - CE conformity - Sino SDS6-3V 3-axis position indicator - 3-jaw lathe chuck Ø 200 mm - Multifix Type B - Coolant device - Work area lighting Specification - Center width: 800 mm - Center height: 180 mm - Turning diameter over bed: 380 mm - Turning diameter via slide: 200 mm - Quill holder: MK4 - Spindle bore: 52 mm - Bed width: 330 mm - Speed levels: 12 - Speed range: 33 - 1500 rpm - Feed speed: 0.072 - 0.54 mm - Metric threads: 0.5 - 3.625 mm - inch thread: 7 - 46 tpi - Motor power: 3 kW - Voltage: 400V - Dimensions WxHxD: approx. 2100 x 1650 x 1050 mm - Weight: approx. 1200 kg

turning diameter: mm turning length: mm control: greates pass round over bed: 750 mm swing diameter over bed slide: 670 mm The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Specifications: Center width 1000 mm Center height 180 mm Spindle bore 52 mm Circumferential diameter over bed 380 mm Circulation diameter over support 185 mm Speeds from 24 - 2000 rpm Drive power 5.5 kW

This VOEST ALPINE WNC 500 S/1.6 Lathe was manufactured in 1992 in Austria. It is equipped with 2-axis (Z-travel 1715mm, X-travel 305mm), a SIEMENS SINUMERIK control. This machine stands out for its stability and is in well maintained condition with direct availabilty. See original tech specs attached.

Lead and Pull Screw Lathe VOEST DA300 Year of construction ca 1980 Turning diameter over bed 600mm Effective turning length: 1850 mm Spindle Passage: 85mm Speeds: 14 - 1000 rpm Tailstock: MK5 Reversal backlash face spindle: 0.5 mm Reversal clearance upper slide: 0.25 mm Rapid traverse bed sledge: in both directions EQUIPMENT - Multifix C - 5 steel brackets - Rotating center tip MK4 - 4 jaw chucks Ø 400mm, plus 3 sets of jaws - 3 jaw chucks Ø 400mm - 3 sets of jaws - Both linings Röhm - Fixed bezel The machine is in good condition. The machine bed is in very good condition.

Description: Speed: 14 - 1000 rpm Center length: approx. 1000 mm Center height above bed: approx. 200 mm Turning diameter over bed: approx. 400 mm Center height above support: approx. 120 mm Turning diameter above support: approx. 240 mm The machine is equipped with a tailstock, a steel holder and a three-jaw chuck Diameter: 160 mm Spindle clearance: approx. 53 mm weight approx.: 800 kg, Approx. Onsite Dimension. (l x w x h): 2,300 x 950 x 1,600 mm

Description: Turning length: 1000 mm Turning diameter over support: 240 mm Approx. Onsite Dimension. (l x w x h): 2,400 x 800 x 1,400 mm, weight approx.: 800 kg

: . centre distance: 2000 mm turning diameter: max. 570 mm spindle bore: 70 mm control: 805 weight of the machine ca.: 3 t The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

turning length: 1050 mm turning diameter: 380 mm centre height: 180 mm turning diameter over slide rest: 200 mm quill:: 4 MK quill stroke: 180 mm turning speeds: 33 - 1500 U/min number: 12 Drehz. bed width: 330 mm spindle bore: 52.0 mm adjustment range:: Ober 130 mm adjustment range:: Plan 330 mm tool adaptor: CAMLOCK GR 6 work height max.: 1060 mm total power requirement: 5.5 kW weight of the machine ca.: 1050 kg range L-W-H: 2000 x 850 x 1450 mm good / well-maintained condition () Furnishing: - 3-jaw chuck Ø 200 mm (CAMLOCK GR 6) - MULTIFIX steel holder, with 4x inserts - robust, movable tailstock - rotating center punch tips - Food key - various other accessories - Coolant device - removable chip tray - rear splash guard - Connection cable + plug - Emergency stop button - User manual (PDF) Machine link: http://mhp.logotech.de/hpm/v7/Datenblatt/datenblatt.php?machineno=1008 -9207355 ...

We offer several machine pallets for Steinel and Heller machines!

Type: 100 FSG, Y&l: 1986, granulation plant with circular gas operation, sifter 100 ATP (4 kW Vario, up to 11,500 rpm), and reblow filter K 6 R (2.4 m2 filter area). All in stainless steel. Very good condition.

Alpine dairymen curve machine, uses type SR28SL construction year 1994

Material: stainless steel Weight: 900 kg Dedusting filter Surface 31,2 m² Accessories: blower, cell wheel air-lock. Very god condition! You can also get the entire system with all components.

Type: 100 FSG, built: 1986, gas operated granulating rig, spray granulator with two media nozzle, separator, heat exchanger (Manufacturer: Ohl), blowback filter K 6 R (2,4 m²), dosing unit for adding seeds. Mint condition.

Material: steel Engine: 75 kW Pin-disk Capasity factor: F=ca. 6,3 Drive: 75 kw Speed: 4900 The machine is as good as new. You can also get the entire system with all components.

Drive: 30 KW

Stand drilling machine in row arrangement, used Gang drilling machine, used Type: BT 6.52 Manufacturer / make: Steinel Built/ new in: 1978 Drilling capacity / drilling capacity: 6 mm in St 60 Spindle cone/ spindle taper: MK 1 Drilling spindle discharge / distance center drill spindle to column: 204 mm Drilling stroke/ way of spindle: 90 mm Table clamping area/ table size: 800 x 390 mm Column diameter/ diam. of coulmn: 60 mm Drilling spindle speeds / speeds of drilling spindle: 1400 / 2800 / 5600 per min/ per minute Total connection value / rated power: 0.25 kW each => 1 kW Weight / weight: approx. 0.4 t

Weight 1750 kg Length x Width x Height 1800 mm x 1350 mm x 3000 mm Machine data: rotor diameter - knife circle : 500 mm length rotor : 630 mm angular speed rotor : appr. 650 min-1 after-run duration : appr. 60 sec. motor power - depent of order: 37 kW / 1500 min-1 45 kW / 1500 min-1 idle power :appr. 30 - 40 % of nominal power. Very good condition, ready to work. You can also get the entire system with all components.

Machine in the very good condition, renewed and ready to use. We can offer to you drive and frame specially for your application. You can also get the entire system with all components.

25 lfm pallet shelf Nedcon New goods, see pictures! A top shelving system from the large manufacturer NEDCON- this is a subsidiary of Voestalpine AG with headquarters in the Netherlands. Height 3.5 m Depth 110 cm, blue Carrier length 2.7 m orange Carrier with load /compartment 3050 kg, Negotiated price: € 1,680,-- net from stock Offer consists of: + 10 pcs pre-assembled frame, depth 110 cm, height 3.5 m + 36 pcs. carrier, length 2.7 m, 3050 kg load/compartment + 72 pcs mount fuses + 20 pcs concrete anchors Load sign documents, etc. are a matter of course. Further accessories can be found in the accessory catalogue. Frame blue RAL 5019, galvanizing inlinations. 2 m to 7 m heights in stock. Field load 12 tons, higher field loads possible on request. Wearer orange RAL 2008. Carrier lengths: 1.85 m, 2.7 m, 3.3 m, 3.6 m in stock. Goods are in stock. ...

40 lfm pallet shelf Nedcon New goods, see pictures! A top shelving system from the large manufacturer NEDCON- this is a subsidiary of Voestalpine AG with headquarters in the Netherlands. Height 5.5 m Depth 110 cm, blue Carrier length 2.7 m orange Carrier with load /tray 3050 kg Negotiated price: € 3,690,-- net from stock Offer consists of: + 15 pcs pre-assembled frame, depth 110 cm, height 5.5 m + 84 pcs. carrier, length 2.7 m, 3050 kg load/compartment +168 pcs. Mount fuses + 30 pcs concrete anchors Load sign documents, etc. are a matter of course. Further accessories can be found in the accessory catalogue. Frame blue RAL 5019, galvanizing inlinations. 2 m to 7 m heights in stock. Field load 12 tons, higher field loads possible on request. Wearer orange RAL 2008. Carrier lengths: 1.85 m, 2.7 m, 3.3 m, 3.6 m in stock. Goods are in stock. Trans ...

Material: steel Engine 11 kW Very good condition. You can also get the entire system with all components.

Engine 18.5 kW Weight approx. 740 kg On basic frame. Very good condition, like new. This machines is overhauled and in very good condition. You can also get the entire system with all components.

Material: Steel Engine: 37 kW Weight: 1,700 kg diameters: 10-60 (mikron) task: kg/h 1200-5000 Speed: max. min 1 2250 This machine is overhauled and like new. You can also get the entire system with all components.

92 lfm pallet shelf galvanized for outdoor nedcon New goods, see pictures! A top shelving system from the large manufacturer NEDCON- this is a subsidiary of Voestalpine AG with headquarters in the Netherlands. Frame: Height 7.2 m depth 110 cm, Strong profiles, reinforced indentation, wind & snow load included. Frames & footplates are sendzimir galvanized. Carrier length 2.7 m hot-dip galvanized, Carrier profiles 130/50mm, carrier with load /compartment 4000 kg Negotiated price: € 15,350,-- net from stock Offer consists of: + 36 pcs pre-assembled frame, depth 110 cm, height 7.2 m +210 pcs. carrier, length 2.7 m, 4000 kg load/compartment +420 pcs. Mount fuses + 72 pcs concrete anchor Surcharge hot-dip galvanized feet incl. support protection € 50,- € net per frame Roof construction on request! Load sign documents, etc. are a matter of course. Furth ...

Stock # U2333-5 Used cutting mill by Alpine model B32/40 RO. Mill has dimensions of inlet into cutting chamber 400 mm x 355 mm. Rotor is equipped with three knives and has diameter 315 mm x length 400 mm. Working rotation of rotor up to 700 rpm. Mill has 3 static knives. Bottom discharge through screen with mesh about 12 mm. Rotor is belt driven by el. motor with power 18.5 kW, 1500 rpm, 400 V, 50 hz. Mill has stainless steel feeding hopper with inlet dimensions: 390 mm x 240 mm. Mill is equipped with two belt conveyers. First feeding material into mill, has width of belt 250 mm, with baffles each 675 mm. Working length of conveyer 290 cm. Top of conveyer is covered with insulation. Second conveyer is for transport product from mill discharge - also has working width 250 mm, with baffles each 675 mm. Working length 200 cm. Mill has also dust filter with exhaust fan and electric contro ...

Used mill Alpine 500.

Weight: 70 kg 18,000 rpm

Material: mild steel Drive: 45 KW Weight: 2000 kg Dimensions: 1500 x 1500 x 1600 mm

Weighing fraes machine STEINEL SH5, table 700 / 200 mm, table lashing adjustment pneumatic