BRANDT used machine for sale

Single-sided edge banding machine Brandt type OPTIMAT KDF 650 C edition Specifications: • Feed rate (m/min.): 8 - 18 • Feed max. with form milling machine (m/min.): 14 • Working height (mm): 950 • Pneumatic connection (bar): min. 6 • Overall length (mm): 6,060 Workpiece and edge parameters: • Workpiece width min. at workpiece thickness 8 - 22 mm: 70 mm (depending on workpiece length) • Workpiece width min. for workpiece thickness 23 - 40 mm: 120 mm (depending on workpiece length) • Workpiece width min. at workpiece thickness 41 - 60 mm: 150 mm (depending on workpiece length) • Workpiece protrusion (mm): 38 • Workpiece thickness (mm): 8 - 60 • Edge height max. = workpiece height (mm): + 6 • Edge Material Roll (mm): 0.4 - 3 • Max. edge cross-section for PVC: 135 mm² • Max. edge cross-section for veneer: 100 mm² • Roll diameter max. ( ...

I am selling a fully equipped edge banding machine BRANDT ProfiLine KDF 790, built in 2006: Configuration: Input stop can be adjusted by menu Manually adjustable joint milling Edge banding with preheating tank Material pressure zone can be adjusted by servo motor Pneumatically adjustable cross-cut saws Heavy milling at the top + at the bottom manually adjustable Radius milling top + bottom servo motor adjustable Groove saw unit at the bottom Round unit 2-motor servo motor adjustable Radius scraper blade R2 pneumatically adjustable / second set R1 included Scraper blade surface Polishing brushes Separator injection at the front Clean injection at the rear Working height adjustable by servo motor Material height 6-60mm Edge material thickness 0.4-12mm Feed speed up to 20m/min. Overall length including feed plate 7860mm Mileage status 1,650,000 meters glued. Incl ...

Key data: 8 mm, 50 mm, 5860 mm

I am selling a fully equipped edge banding machine BRANDT Optimat KDF 550 C, built in 2006: Configuration: Manually adjustable entrance stop Manually adjustable joint milling Edge banding EVA Material pressure zone can be adjusted by servo motor Pneumatically adjustable cross-cut saws Radius milling top + bottom manually adjustable Round unit 2 motor manually adjustable Radius scraper R2 pneumatically shut-off Scraper blade surface Polishing brushes Control panel Power Control PC20+ Working height adjustable by servo motor Material height 8 - 50mm Edge material thickness 0.4 - 8.0mm Feed speed 11m/min. Assembly length including feed plate 5860mm Total weight 2660kg Very good condition, fully functional!

Key data: 3 mm, 50 mm, 4150 mm

I am selling a fully equipped edge banding machine BRANDT Ambition 1220, built in 2010: Configuration: Manually adjustable entrance stop Manually adjustable joint milling Edge Banding EVA Glue Manually adjustable material pressure zone Pneumatically adjustable cross-cut saws Radius milling top + bottom manually adjustable Round unit 1 motor manually adjustable Radius scraper R2 pneumatically shut-off Control panel Working height adjustable by servo motor Material height 8-50mm Edge material thickness 0.4-3mm Feed speed 10m/min. Overall length including feed plate 4150mm Total weight 1320kg Very good condition, fully functional!

Shape milling machine Brandt type FP 10 Specifications: • Year of construction: 1989 • Workpiece thickness max. (mm): 55 • Workpiece width min. (mm): 80 • Profile depth max. (mm): 80 • Inner radius min. (mm): 10 • Edge material thickness max. (mm): 3 - depending on radius and edge material • Milling motor: 0.5 kW, 27,000 rpm. • Electrical: 220 V - 1 Ph. - 50 Hz • Power supply (kW): 0.5 • Compressed air connection (bar): 6 • Dimensions L x W x H (mm): 850 x 650 x 1430 • Working table height (mm): 1000 • Swabing unit: for processing thick PVC edges • Weight (kg): approx. 120

Postforming machine in cycle Brandt type PF 20/31 Specifications: • Working length max. (mm): 3100 • Profile height max. (mm): 200

BRANDT KDF 660 Profiline single-sided edge banding with joint milling, pre-milling, fine milling, 2-fold corner copying, radius drawing blade, flat-drawing blade and babble units Type: KDF 660 Profiline Specifications: BRANDT KDF 660 Profiline with joints and corner rounds Preheating of the tool stucco IR preheating Edge thickness 0,4 - 15mm Banding height max. 66 mm, with program high adjustment Caps from the roll at 3mm thickness max 45mm height or 0.8 65mm Plate thickness max. 8-60 mm for corner copying max 40mm Control PC20+ link control (loss of contact), with modem for remote service/maintenance 1. Joint unit program Adjustment of the infeed line 2. Bandkapmesser 3a. Radiant heater High-strength bonding by workpiece preheating 3b. Spray anti-adhesive 3c. Quickmelt Glue Mel Mel Application Unit with Quick Change 3d. Leimangabe by means of glue rol ...

Multispindle drilling machine Brandt DB 19H Distance between spindles 32mm Number of spindles 19 Distance between extreme spindles 680mm Spindle speed 2800 rpm Motor power 1.5kw Working pressure 6bar Weight: 405kg

- year of manufacture 2001 -DTR - after HOMAG service - pre-cutter, earning corners - wooden glue up to 9 mm TECHNICAL PARAMETERS: machine tool adapted for machining PVC/ABS flanges veneer up to 3 mm thick and wood stickers up to 9 mm thick pre-cutter - milling the board belt pressure tank with glue, for hot melt glue granules additionally roll for applying glue heated strip tape strip guillotine - pre-cutting veneer 3 pressure rollers 2 ready-made ball cutting units 2 edge milling units (radial cutters) corner earning unit (milling) scraper aggregates - for removing excess glue polishing units .max. element thickness 50 mm Min. element width 60 mm Min. element length 160 mm feed speed 96 m/min total power 10,8 kW extraction connection diameter 120 mm dimensions (L/W/H) 5700 / 1200 / 2100 mm weight 2000 kg

Equipment: - Quick-change gluing part for hot melt adhesive - Autom. Edge magazine with roll plate - Pressure zone with pneum. pressurized pressure roller and 2 free-running repressure rollers - Power Control PC 20+ control - Inlet ruler adjustable - Joining milling unit 2 x 2.2 kW - pneum. Adjustment caps, drawing blade, program adjustment side button rollers and pneum. 2-point adjustment vertical probe rollers - Cross-cut unit 2 x 0.18 kW - Milling unit 2 x 0.55 kW - Mould milling unit 1 x 0.35 kW - Drawing blade unit for PVC edges - Surface drawing blade glue joint - Cleaning agent specification workpiece - Schwabbelaggregat Specifications Edge thickness 0.4 - 8 mm Roller cutting max. 3 x 45 mm or 0.8 x 65 mm Workpiece thickness 8 - 60 mm Feed max. approx. 11 m/min. Electrics 400 V - 3 Ph. - 50 Hz Connection value approx. 10.5 kW Pneumatic connection 6 bar To ...

Edge banding machine Brandt type KTD Specifications: • Glue pot • Conversion: carried out by the company Hüttenhölscher in Verl • Field of application: Adhesive application system for handle strips • Vacuum table: included • Automatic pressure zone: included

Equipment: - Machine stand throughout - Fixed stop side right - Paint finish Grey RDS 240 80 05 - Inlet ruler motorically adjustable, extended by 300 mm - Inlet lock pneumatically controlled - automatic edge feeder - Upper pressure: belt upper pressure - Height adjustment motorized - Position display and input centrally via the controller - Transport chain with rubber support, 80 mm wide - automatic central lubrication for the transport chain - Workpiece support in scissor design, approx. 1000 mm extendable - Noise protection equipment - Hood interior lighting 3 lamps - Control Power Control PC20+ Aggregate technology: - Joining milling unit 2 x 2.2 kW 200 Hz (60 mm joining milling cutter set) - Gluing unit A15 (workpiece preheating, QA34 application unit, infrared adhesive activation, magazine for rolls and fixed lengths, pressure zone with motorized adjustment, driv ...

Edge banding machine Brandt Optimat KDF 1600 GC YOC 2009 Edge thickness 0.4 - 12 mm Plate thickness 8 - 60 mm Feed 12 m/min Inlet ruler adjustable Pneumatic package Automation package Quickmelt Premelting Unit Joining milling unit 2 x 2.2 kW Cross-cut unit chamfer / Straight 2 x 0.35 kW Milling unit 2 x 0.55 kW Mould milling unit 2 x 0.35 kW (2 units) Drawing blade unit with quick-change heads Surface drawing blade for glue joint Schwabbelaggregat 2 x 0,18 kW Electronics control Connection value 11.5 kW Machine length approx. 6600 mm Weight 2900 kg

Edge banding machine with joint/form milling machines Brandt Highflex 1220 FC YOC 2015 Workpiece thickness 8 - 60 mm Edge thickness 0.4 - 3.0 mm Feed speed 10 m/min Joining Milling – DIA Tools Gluing unit Contact heating shoe Pressure zone Pneumatic Package Cross-cut unit Flush milling unit Profile drawing blade unit Schwabbelaggregat Electronics control Machine length 4200 mm Machine dimensions W x H 1300 x 2180 mm Weight 1400 kg

Equipment: - Quickmelt gluing part for hot melt adhesive - Automatic edge magazine for rolls and fixed lengths - Heavy pressure zone with driven, pneumatically applied main pressure roller and 2 free-running repressure rollers. (adjustable by program) - motor-adjustable upper pressure. - Control panel on the machine inlet. - Electronic control power control PC 20+ - Feed variable 8-14 m/min - PU overpressure rollers - Inlet ruler adjustable by program - Joining milling unit 2 x 2.2 kW - Bevel cross-cut unit/straight 2 x 0.18 kW - Milling unit 2x0.55 kW (adjustable by program) with multiple roller pressing - Mould milling unit top+bottom, 2 x 0.35 kW - Drawing blade with quick-change heads and additional device for pointed workpieces - Glue joint drawing blade - Schwabbelaggregat - Automation package for 1-milling machines, consisting of: 3175 - Pneumatic Adjustment Caps ...

Equipment: - Quick-change Quickmelt gluing part for hot melt adhesive. - Automatic edge magazine with roll plate and autom. Edge feeder - extended inlet ruler, adjustable - heavy pressure zone (with pgroamm adjustment) with a driven main pressure roller, as well as 3 repressure rollers - Motor-adjustable upper pressure. - Control panel on the machine inlet. - Electronic control PC 16 - Modem for remote service and remote maintenance - Noise protection cladding - autom. Chain track central lubrication - Interface for return (electronic) DAHR01/02/15 Aggregate assembly - Release agent specification workpiece - Joining milling unit 2 x 2.2 kW - Cross-cut unit 2 x 0.35 kW, pneum. Adjustment chamfer/straight - Milling unit 0-25 degrees, 2 x 0.55 kW counter-rotation, to flush milling machine, pneum adjustable pneum. 2-point adjustment Vertical probe rollers - Milling unit ...

One-sided edge gluing machine in right version for hot melt adhesive gluing. equipment: - Glued part for hot melt adhesive granules - Autom. Edge magazine with roller plate - Pre-cap scissors - Pressure zone with hooded pressure roller and 2 trailing rollers - centrally adjustable upper pressure - Cap unit 2 x 0.27 kW - Büdig milling unit 2 x 0.35 kW - Drawing blade unit for PVC edges (chamfers/rounds of pre-milled PVC edges) - Swib ledunit 2 x 0.18 kW specifications: Edge thickness 0.4 - 5 mm Roller separation max. 3 x 30 mm (PVC) or 0.8 x 60 mm Workpiece thickness 10 - 50 mm Workpiece width min. 70 mm Workpiece length min. 160 mm Feed 11 m/min. Electric400 Volt - 3 Ph. - 50 Hz Connection value approx. 5 kW Pneumatic connection 6 bar Total length 4000 mm Weight approx. 1050 kg

Edge glue Brandt Type: KD 86 Built: 1993 Edge thickness up to 12 mm Glueing of roll up to 3 mm with pneumatic cross-cut station Glued part with Quickmelt pre-melting tank Heavy pressure zone with one driven and three reprint rollers Saw cutting station for the front and rear overstanding Milling station flush / chamfer Second milling station radius milling R 3 mm Corner copying with pass Radius drawing blade R 3 mm Chip catching box Schwabbelstation Pneumatic package for post-processing agregates Extendable support for large parts Control panel at eye level Space requirement approx. 6100 mm

for bill of exchange order unit

Edge gluing machine Brandt Type: KTD 14 Built: 1996 Edge gluing machine with direct glue indication for gluing Edge materials on straight workpieces. Processing units: Install Glue indication Roller separation Flush milling Caps Workpiece thickness 10 - 40 mm Edge material thickness 0.4 - 1.2 mm Workpiece width min. approx. 50 mm Workpiece length min. approx. 260 mm Feed 6 m/min. Operating voltage 400 V+/- 10% - 3 Ph - 50 Hz Heating capacity 1.2 kW Connection value 3.04 kW Electrical connection cable length approx. 4.5 m Compressed air connection 7 bar Operating pressure 6 bar Weight: approx. 150 kg Space requirement: approx. 1800 x 1600 mm

• max workpiece thickness: 55 mm • min. workpiece width: 80 mm • max profile depth: 80 mm • max edge thickness: 3 mm • Table size: 800 x 380 mm • Foot pedal operation • Adjustment via mechanical counters • Weight approx. 120 kg (Changes and errors in the technical data and prices reserved!)

- with lateral Kappsaege

Workpiece length: 1800-4200mm, max. profile height: 200mm, min. workpiece thickness: 16mm, working height: 950mm, connection cable: 12kW, length: 6250mm, height: 2050mm, weight: 3.8t.

Description: BRANDT KDF 660 Profiline with joint cutter and corner rounder PU glue (and hot melt glue) Workpiece preheating: IR preheating Edge material: 0.4 - 15.0 mm Max. width of edgebanding: max. 66 mm (at 1 mm band thickness) Edging material on the roll: Max. 6 mm to 45 mm, max.0.8 to 65 mm Workpiece thickness: Max. 8-60 mm Control: PC20+ Streckensteuerung with modem for teleservice 1. Joint milling 2. Chopping knife 3a. Pre-activation with IR heating 3b. Anti adhesive spray device 3c. Pre-melter, for quick change of adhesive 3d. Glue aggregate with glue application roller in follow-on or counterflow 3e. Program-controlled pressure zone 4. Capsaws - adjustable 0° - 15° 5a. Coarse milling (Bündig milling) -radial Milling units with 2-point adjustment, flat, phase radius up to 12 mm edge thickness 5b. Fine milling, with program-controlled adjustment for thickness, plane, phase or r ...

Description: Brand: Brandt Type: KDF 210 Year of construction: 2014 Machine number: 0-261- 20-7902 Control: Easy Control 10+ Speed-controlled track control with optical start-stop indication sensors Control screen: LCD, 4 lines of text, ergonomically integrated on the input side on the hood Configuration: Chain conveyor transport Central lubrication Upper pressure/ guidance: via central adjustment with 2 rows of rollers positioned offset to each other Joint cutters: (2x) 0.75 kW, 200 Hz Diamond-tipped tool, manual positioning (Siko counters), max. 3 mm overhang and max. 40 mm workpiece thickness Glue unit: A3 glue unit for hot-melt and possibility for PU glue application Glue output roller under workpiece in following or counterflow mode Heavy-duty cutter Pressure zone: Pneumatically driven 1st pressure roller, 2nd roller running freely ensures good compaction Hacksaws: (2x) ...

Description: Type of edging Thin edge Thick edge Gluing System EVA Hotmelt Premilling Unit yes Corner Rounding Unit yes Max feed speed 11 m/min Maximum panel thickness 50 mm Operating Units 8 nr Min. panel height 8 mm Max. panel height 50 mm Min. edge thickness 0.4 mm Max. edge thickness 3 mm Max. forward feed speed 11 m/min Top pressure yes Panel support guides yes No. Panel Sizing / Milling units 1 NO. PANEL SIZING / MILLING UNITS 1 Unit : pre-milling unit automatic timed intervention : yes motor power : 2.2 KW Edge coil magazine yes no. positions 1 Gluing system yes glue pot for EVA hot melt glue yes Roller set to press the edge yes no. pressure roller 3 No. Edge Processing Units 5 NO. EDGE PROCESSING UNITS 1 Processing Unit : end trimming no. motors : 2 motor power : 0.18 KW r.p.m. : 12000 RPM NO. EDGE PROCESSING UNITS 2 Processing Unit : top and bottom rough trimming no. motors : 2  ...

Description: Max. panel height 50 mm Min. panel width 70 mm Min. edge thickness 0.4 mm Max. edge thickness 3 mm Max. forward feed speed 10 m/min Pressure with idle wheels Panel support guides NO. PANEL SIZING / MILLING UNITS Unit : pre-milling unit Edge coil magazine Gluing system glue pot for EVA hot melt glue Roller set to press the edge no. pressure roller 3 NO. EDGE PROCESSING UNITS 1 Processing Unit : end trimming no. motors : 2 motor power : 0.18 KW r.p.m. : 12000 RPM NO. EDGE PROCESSING UNITS 2 Processing Unit : fine trimming to trim and round no. motors : 2 motor power : 0.27 KW r.p.m. : 12000 RPM NO. EDGE PROCESSING UNITS 3 Processing Unit : Corner rounding NO. EDGE PROCESSING UNITS 4 Processing Unit : edge scraping NO. EDGE PROCESSING UNITS 5 Processing Unit : glue scraping Control system PLC Safety standard CE mark Approx. Onsite Dimension. (l x w x h): 1 x 1 x 1 mm, weight ap ...

Description: Max. panel height 55 mm Min. edge thickness 0.4 mm Max. edge thickness 12 mm Max. forward feed speed 13 m/min Pressure with idle wheels NO. PANEL SIZING / MILLING UNITS Unit : pre-milling unit automatic timed intervention motor power : 2.2 KW Edge coil magazine glue pot for EVA hot melt glue premelter for EVA hot melt glue Roller set to press the edge no. pressure roller 4 NO. EDGE PROCESSING UNITS 1 Processing Unit : end trimming no. motors : 2 automatic timed intervention motor power : 0.35 KW r.p.m. : 12000 RPM NO. EDGE PROCESSING UNITS 2 Processing Unit : fine trimming to trim and round no. motors : 2 motor power : 0.55 KW r.p.m. : 11300 RPM NO. EDGE PROCESSING UNITS 3 Processing Unit : Corner rounding no. motors : 2 motor power : 0.4 KW NO. EDGE PROCESSING UNITS 4 Processing Unit : glue scraping NO. EDGE PROCESSING UNITS 5 Processing Unit : buffing no. motors : 2 motor  ...

Description: Type of edging Thin edge Thick edge Solid wood Gluing System EVA Hotmelt Premilling Unit yes Corner Rounding Unit yes Max feed speed 14 m/min Maximum panel thickness 60 mm Operating Units 8 nr Min. panel height 8 mm Max. panel height 60 mm Min. panel width 70 mm Min. edge thickness 0.3 mm Max. edge thickness 3 mm Max. forward feed speed 14 m/min Top pressure yes Pressure with idle wheels Panel support guides yes with positioning by NC yes No. Panel Sizing / Milling units 1 NO. PANEL SIZING / MILLING UNITS 1 Unit : pre-milling unit automatic timed intervention : yes motor power : 2.2 KW Lamps to preheat the side of the panel yes Edge coil magazine yes no. positions 1 Gluing system yes glue pot for EVA hot melt glue yes premelter for EVA hot melt glue yes Roller set to press the edge yes no. pressure roller 3 with positioning by NC yes No. Edge Processing Units 6 NO. EDGE PROC ...

Description: Type of edging Thin edge Thick edge Solid wood Gluing System EVA Hotmelt Max feed speed 9 m/min Maximum panel thickness 50 mm Operating Units 4 nr Min. panel height 8 mm Max. panel height 50 mm Min. edge thickness 0.4 mm Max. edge thickness 3 mm Max. forward feed speed 9 m/min Top pressure yes Pressure with idle wheels Panel support guides yes Edge coil magazine yes no. positions 1 Gluing system yes glue pot for EVA hot melt glue yes Roller set to press the edge yes no. pressure roller 3 No. Edge Processing Units 3 NO. EDGE PROCESSING UNITS 1 Processing Unit : end trimming no. motors : 2 motor power : 0.18 KW r.p.m. : 12000 RPM NO. EDGE PROCESSING UNITS 2 Processing Unit : fine trimming to trim and round no. motors : 2 motor power : 0.27 KW r.p.m. : 12000 RPM NO. EDGE PROCESSING UNITS 3 Processing Unit : glue scraping Safety standard CE mark yes Total installed power 3.5 KW  ...