Used and refurbished turbine mill from Tecnoecology for the digestion of old cables, especially fine strands or computer cables. Balling takes place at about 3,000 rpm. The tools are rotatable and have 4 usable edges. The turbine mill can be operated stand-alone or integrated into an existing system without a pellet mill. The machine has a 20 kW drive and can process up to approx. 300 kg of material per hour.
Machine for processing mixed old cables including fine conductors and stranded cables, Due to the special rotor system and the large flywheel masses, the system is also suitable for operation in manual insertion. The machine is equipped with a cooling unit that optimizes the granulator with a flow temperature of 0.5 °C for the use of heat-sensitive cables, such as NYM etc. The control electronics of the system enable fully automatic operation in a line with pre-shredder, conveyor belt, dosing accumulator, etc. The machine includes several sets of knives and different screens.
Small but very robust and powerful shredder for a wide range of tasks such as old cables, plastics, wood, etc. With hydraulic, electronically controlled feed. Drive 18.5 + 2.2 kW (rotor + feed). Rotor shaft with connections for connecting a cooling unit (e.g. when used for old NYM cables. The machine is and little used from our demo machine inventory. The machine is offered with a one-year used machine warranty.
The JMC 407 is the top seller among our alligator claws. It is cost-effective, has sufficient knife length and enough power for most metal recycling tasks. It is suitable for cutting many materials, such as profiles, piping, motors, gearbox housings. The scissors are also often used for cleaning scrap metals or cutting vehicle radiators. The machine is equipped with a control system without electronics and a manually adjustable hold-down device, which also acts as a protective cover. By means of a foot pedal, the scissors can be used in single or continuous operation. The opening width can be adjusted by means of simple clamping screws. The scissors are from our demonstration pool and can be viewed or tested.
Large Four Shaft Shredder with Two Cutting Shafts and Two Feed Shafts. Until now, the shredder has been used as a pre-shredder for the recycling of old cables. Due to the hydraulic tamper, the shredder can also be used for bulky materials. Changing the screens is hydraulically assisted and therefore easy to do. On request, the shredder can also be supplied with the articulated conveyor belt shown here. The conveyor belt is equipped with a magnet in the upper pulley for iron separation.
Used, heavy and high-performance recycling plant for the recycling of old cables. The machine has a granulator with a knife length of 500 mm and a large cutting table. As a result, the Sincro 530 from Guidetti achieves hourly outputs of 450 to 600 kg (manufacturer's specs). The system was traded-in by us and all essential components were checked in the workshop. The machine works reliably and trouble-free. On request, the system can be equipped with pre-shredders and conveyor belts. Feel free to visit us and get your own impression of the machine. You are also welcome to test the machine with your cable material.
Small dosing accumulator with screw conveyor for cable recycling plants, wood chips, etc. Capacity approx. 650 litres or 400 - 500 kg of pre-shredded old cable Adjustable conveying speed with frequency converter/inverter 0 - 16 rpm Drive only 0.55 kW with reduction gear Discharge height approx. 750 mm Dimensions (LxWxH): 2,200 mm x 800 mm x 1,800 mm Mobile via large heavy-duty castors with brakes
Used single-shaft shredder for wood, plastics, old cables, etc. Of course, the machine has received new knives and has been checked by us. Accordingly, we give 3 months of used machine warranty. The shredder has the amplified 30 kW drive (normally 15 kW) and is therefore enormously powerful. The rotor stops in the event of overload or blockage and reverses automatically. The hydraulics of the machine are dry, there are no leaks. Currently, a screen with a hole diameter of 14 mm is used, so that it is perfect for old cables. Of course, other screens in the range of 10 mm to 60 mm can also be used. The shredder is immediately available and can be viewed and tested. Further technical data: Rotor length: 630 mm Rotor diameter: 250 mm Feed travel: 600 mm Loading opening: 1,100 x 1,100 mm Drive rotor: 30 kW Drive hydraulics: 1.5 kW Rotor speed approx.: 90 rpm Weight ...
Used vibrating vibrating screen with two sieve inserts for three fractions. The sieve was used for the post-cleaning of plastic granules from cable recycling. The lower deck has an additional perforated plate with anti-clogging cleaning balls. The screen comes with inserts of 0.8 mm, 1.3 mm and 2.3 mm.
Simple unit for transporting plastic granules, such as PVC from cable recycling. Suction through hopper and 100 mm flex tube. Forwarding by fan/fan in rotary valve for dust removal. By extending the pipes, the unit can also be located further away from the feeding point. The big bags are suspended by height-adjustable chain hooks. The unit consisting of a rotary valve and filter is also adjustable in height. Of course, boxes can also be used instead of big bags. The machine can be inspected and tested with us.
Heavy conveyor belt for the recycling of old cables or other materials. The 30 cm strap is designed with concealed lateral pleated bars so that no wires or other material can get stuck in the gaps. The 0.75 kW drive motor is also equipped with a reduction gear, which significantly reduces the conveying speed. The conveyor belt is only used a little and therefore shows hardly any signs of wear.
Very good machine from our demonstration pool. Few hours of operation or signs of use. The peeling machine is suitable for XLPE cables, underground cables, cables with steel armouring, cables with aluminium and lead armouring, but also for processing PVC and rubber cables. With this machine, two cuts can be made at the same time in one operation, so that the processing can be twice as fast as with other models. Technical data: Working range/cable diameter: 30 mm to 150 mm Pulling speed: max. 12 m/min Motor: 2x 3.0 kW - 400 volts Dimensions (LxWxH): 1.8 x 1.0 x 1.2 m Weight: approx. 660 kg
Used overband magnet with new conveyor belt, new geared motor and new bearings. Length, strap 1,200 mm, magnet 700 mm Strap: width 300 mm, 5 studs Drive: 400V, 0.18 kW Aluminum frame with 4 eyebolts for suspension.
Cable recycling plant with many innovations in all plant components for up to 600 kg/hour (depending on material) The basis of this recycling plant is modularly constructed from strong and innovative individual components. In the standard version, the following structure is obtained. - Preshredder MR 4080 or MR 40-100 - Conveyor belt with magnetic separator - controlled by PLC - Granulator C 600 with axle length 600 mm, 5 rotor blades and 37 kW drive, cooling of the housing by unit against adhesions - Z-separator for the separation of heavy copper or 1 granulate - Dosing drum for the optimally uniform feeding of the following turbine mill - Ghibli 545 turbine mill (new model), optionally with coolable housing and inverter control - SA 600 separation table, new version with PLC inverter control of the air volume + eccentric drive with inverter control of the oscillation + adju ...
Young used machine with very few hours of operation. Compact cable recycling plant with low connected load for 80 - 120 kg/hour (depending on material) This system can be operated with a pre-shredder via a conveyor belt as well as in direct insertion. The system still has the original, unground set of knives, so it can hardly have more than 40 to 50 operating hours. Therefore, we offer this system including a 12-month used machine warranty. Pre-shredders, conveyor belts, dosing accumulators, etc. can also be obtained from us.
Used cable recycling plant Tecnoecology T 250 Turbo Year of construction: 2008 The plant consists of the following parts: - Pre-shredder: Bano MAC 630, approx. 250 - 400 kg/hour, depending on material - Conveyor belt to the dosing accumulator, approx. 4.0 m - Dosing accumulator with discharge conveyor, approx. 1.5 m³ - Controlled conveyor belt with belt magnet for feeding the granulator, approx. 4.0 m - Granulator GA 400/30, approx. 250 - 400 kg/hour, depending on material - Turbine mill, T 25-2, built in 2019 - Separator TV 300, inverter controlled, separation table 80 μm - Dust extraction and filter system The entire system currently achieves between 200 and 300 kg/hour in operation, depending on the cable composition. On request, additional components, such as a big bag loading for the plastic or the re-screening of the granules, can be supplied. The plant is curre ...
Used conveyor belt, built in 2020, few operating hours Very heavy design for recycling With very strong neodymium magnet in the upper deflection drum Reducing gear for slow conveying speed With concealed wavy edge and crossbars on the harness Large inlet hopper with adjustable slider for material height on the belt 4 m long, discharge height approx. 2.2 m (variable) Ideal, for example, for feeding material into a cable recycling plant At call
Compact but powerful machine for processing old cables up to approx. 25 mm in diameter. The nominal output of the system is 120 kg/hour when using a 4.0 mm perforated screen. By using a pre-shredder, the performance can be significantly increased, then stronger cables are also possible. The machine has been checked and modified in our workshop. - new dividing table - new set of knives - new sieves - new seals - Connection for refrigeration unit - Connection for feed and conveyor belt On request, we can supply additional accessories for the machine, such as: - Pre-shredder -Magnetic drum - Dosing accumulator - Refrigeration unit - Dust filter - Screening drum - Bigbag stand with air conveyance for plastic granules
Small floor filter, which can be used, for example, for extracted air from separators in cable recycling. The filter is without its own fan, so it works purely passively. The filter and the collection bags have a diameter of 500 mm.
