We use cookies to optimize our website for you and to be able to continuously improve it. By continuing to browse the site you are agreeing to our use of cookies.
Disagree
used
Capacity: 250 tonnes Factory no. 233 A
used
Sell a press on behalf of the factory, which was fully functional until the plant was shut down. Pressing force 250 tons Length 3050mm Sheet thickness max 15mm A lot of accessories Dimensions transport approx. 3,2m 2m 3,5m high 20to Removal must be organized by the buyer. Crane rental nearby, it can be helped supportively.
used
Manufacturer: Weinbrenner Type: TSV 6 / 3050 Year of constr.: End of 2015 demonstration machine Cutting length: 3050 mm Cutting capacity: 6 mm (steel) Hours of operation: 54 Control: Cybelec DNC 60 Dimensions L/W/H: 4100/2050/2100 mm Table height: 1000 mm Weight: 8500 kg Min. cutting angle: 1° Cutting angle max.: 2.5 ° Stroke rate minimum: 20 min. Max speed: 25 min. Cutting gap adjustment: motorized Cutting angle adjustment: hydraulic Number of holders: 14 Rear velocity range: 1000 mm Security: setting the photocell safety on the front and back Oil filling: 225 l Electrical power: 15 KW Power consumption: 3 x 400 V / 50 Hz Back-up fuse: 50 A Additional equipment: Extension of the side stop on 2050 mm Side stop side swing-away A total of 8 support arms freely movable along the entire length of the table The machine is a demonstration machine in mint cond ...
used
Working width: 3050 mm sheet thickness: 6 mm throat depth: 200 mm rear gauge: 1000 mm power: 15 kW space: 4100 x 2300 x 2100 mm weight: 8500 kg well-preserved CNC hydraulic shear, with pivoting Panel, serial control. CYBELEC, CNC 1000, Hours of operation according to the operating hour counter: 2700 h
used
Working width: 4100 mm sheet thickness: 16 mm projection: 300 mm rear gauge: 1500 mm power: 400 V, 45 kW space: 4800 x 3500 x 2600 mm weight: 28000 kg
used
Length: 9500m, width: 6500mm, height: 3800mm, weight: 35t, max. press force: 4000kN, working stroke: 450mm, ram stroke: 450mm, hydraulic pressure: 283bar, bending length: 4. 550mm, clear column width: 4050mm, column projection: 400m, tool holder: 25mm, control: Cybelec ModEva 15S under Windows 7, installed in 2018, operating hours: approx. 60,000 (meter defective), on-site inspection is possible.
used
used
pressure: 250 t chamfer lenght: mm throat: mm stroke of ram: mm The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
used
The machine is in good technical condition. Nominal forming force: 50t Max. sheet length: 3000mm Upon agreement, the possibility of inspection in progress.
used
This Weinbrenner GP400 Bending machine was manufactured in the year 2006 and has 60000 production hours. It is equipped with a Cybelec ModEva 15S control unit. The machine has a pressing force of 4000 kN and a bending length of 4550 mm.
used
Hand guillotine shears, guillotine shears, sheet metal shears, sheet metal shears, folding machine, edging bench -Hand guillotine shears combined with: folding machine -Cutting width: 610 mm -Max. Section thickness: 1.0 mm -Swivel bending machine -Max. Working width: 610 mm -Max. Sheet thickness: 1.0 mm -Transport dimensions: 845/910/H1230 mm -Weight: 240 kg
used
pressure: 160 t chamfer lenght: 3050 mm distance between columns: 2550 mm Control: CYBELEC VisiTouch Pac stroke of ram: 300 mm weight: 14000 kg The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
used
pressure: 200 t chamfer lenght: 3050 mm distance between columns: 2550 mm Control: CYBELEC VisiTouch Pac stroke of ram: 524 mm weight of the machine ca.: 17.000 kg The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
used
pressure: 100 t chamfer lenght: 2050 mm distance between columns: 1550 mm throat: 250 mm stroke: 200 mm adjustment of press crosshead: 200 mm stroke speed - idle stroke downwards: 105 mm/sec stroke speed - idle stroke upwards: 180 mm/sec stroke speed - under load: 9,5 mm/sec table width: 200 mm table height over floor: 900 mm dayligth: 280 - 480 mm back stop - adjustable: 3 - 729 mm control: CYBELEC SYNCHRO control: CNC 7400 PS total power requirement: 7,5 kW weight of the machine ca.: 10 t dimensions of machine L x W x H: 3,70 x 2,45 x 2,80 m Accessories: programmable back gauge, table extensions, various upper and lower dies segments The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
used
CNC-controlled hydr. Sheet metal shearing machine make WEINBRENNER type TSV 6/3050Machine -No: 687 T built in 1987gr. Working width: 3050 mmFor sheets with 45 kg strength up to: 6.0 mmclear column width: 3160 mmclear stator projection: 200 mmCutting angle min./max .: 1/2 °Backgauge adjustment: 1000 mmNumber of hydr. Hold down: 12Number of strokes min./max. (depending on cutting length and material thickness): 22/36 / minHydraulic drive: 380 V, 15 kWTable height above hall: 900 mmDimensions incl. Backgauge, without frontSupport arms: 4100 x 2300 x 2100 mmWeight approx .: 8500 kgWith- Control in swivel control panel CYBELEC CNC 1000- compl. elec. Device with control device in the large switchingxa0Cabinet attached to the side of the machine- Backgauge control with programming- Material quality code- Sheet thickness preselection- stroke length adjustment- Contact cutting device- Scrapweed- ...
used
Capacity: 1250 t Folding length: 4100 mm Make Weinbrenner Type AP 1250 Year 1976 Heavy duty pressbrake Capacity (metric tons)Force = 1250 T Folding length (mm)L = 4.100 Down stroke or Up stroke 2 x 30 kW Tandem type Die height = 1.000 Throat = 450 mm Speed = 45 / 6 / 50 mm Between column = 3.050