We use cookies to optimize our website for you and to be able to continuously improve it. By continuing to browse the site you are agreeing to our use of cookies.
Disagree
used
Key data: 1530 mm, 4 mm
Schröder MHSU 1500/4,0 - Motorized guillotine shears - Motorized backgauge 750 mm - Hold-down device with hard rubber strip to protect polished sheet metal - Extended extendable support table - All-steel knife 2-flute - Punctures at a distance of 10 mm parallel to the lower knife over the entire course of the table - Selector switch for single and continuous stroke - Rear compartment protection according to CE via 3-beam light barrier and side protective grille -Foot switch - Year of construction 2013 Specification - Effective length: 1530 mm - Capacitance (Rm 400 N/mm²): 4.0 mm - Cutting angle: 2.7° - Stroke rate: 34 rpm - Drive power: 4.0 kW - Nominal power: 5.0 kVA - Power supply: 3x 400 V - Dimensions WxHxD: 2100 x 1410 x 2600 mm - Weight: 1250 kg
used
Key data: 1550 mm, 6 mm
Type HSS 1500 x 6 mm Specifications: Cutting length 1540 mm Sheet thickness in St 6 mm Projection 250 mm Back gauge up to 750 mm
used
Offer 23476 Specifications: - Max. working width 1020 mm - max. material thickness 3.0 mm - Cutting angle 2.7° - electr. Footswitch - Single stroke – continuous stroke can be pre-selected - Manual backgauge up to 500 mm - Front pull-out sheet metal support - Drive 400 V / 2.5 kW - Space requirement approx. W 1450 x H 1200 x D 1400 mm - Weight approx. 900 kg
used
Product number: 2829 Type: IMAX620 Serial number: 620.3023.03 Year of construction: 2003 Belt width: walking beam, 620 mm Needles: 2 x 150 pcs, 3 mm Product height: max 200 mm Speed: 15 - 60 cycles/min. Advance: 50 / 100 mm Compressed air: 6 Bar Power: 3 x 400V, 50Hz, 16.5kW Dimensions: 2150 x 1600 x 2350 mm For boneless and bone-in products Including tool trolley Schröder rotating filter Type: DF510 Serial number: 634-11 Year of construction: 2011 Power: 3 x 400V, 50Hz, 0.22kW Dimensions: 1000 x 2650 x 1350 mm Schröder tube heat exchanger Type: RWT Serial number: RWT-5622-13 Dimensions: 400 x 1700 x 500 mm
used
Used drawing press SCHRÖDER, type: Hamax 800 incl table For machine filling of fresh or cured meat parts into artificial casings.
used
offer 22557 Specifications: - working width 4020 mm - material thickness at 40 kg / mm² strength 2 mm - Bending angle adjustment electronically preselectable 0 - 135 ° - largest opening width / stroke of the upper cheek 250 mm - controlled mot. Height adjustment of the bending bar 50 mm - Height adjustment of the lower wall 50 mm - Upper cheek drive 400 V / 2.2 kW - Bending cheek drive 400 V / 3 kW - with - 3 axis positioning control POS 500 - controlled backgauge 10 - 1000 mm - Space requirement with backgauge approx. W 4900 x H 1650 x D 2400 mm - Weight approx. 4500 kg
used
Schröder Curing Oven - Width: 130 cm - Depth: 160 cm - Height: 190 cm Good condition fully functional can be visited and tried on site. Shipping also abroad. Sightseeing: Basically, I would like to point out that the article, in order to avoid misunderstandings, can be viewed before buying and tested under electricity. Please ask questions before purchasing to avoid ambiguity. For general questions or an appointment for a visit, I am always available at the telephone number below or above. Errors in description and prior sale excepted. VAT will be shown separately on my invoices. Shipping with freight forwarder.
used
Product number: 2471J TypeI: MAX420 Serial number: 4201 1061 Year of construction: 2006 Needles: 108 pieces of 3 mm Walking beam: 420 mm Advance:50/100 mm Product height: max 140 mm Cycles: 15 to 60 per minute Compressed air: 6 Bar Power: 3 x 400V, 50Hz, 16kW Dimensions: 2300 x 2200 x 2300 mm Including rotating filter
used
Warehouse number: 3726 SHEET METAL BENDING MACHINE Manufacturer: SCHROEDER , Type: 2500 x 2.5 mm Machine NO.: 6290, Year of construction: 1987 Specifications: Size bending length 2550 mm Size sheet thickness 2.5 mm Program-controlled backgauge. Siemens - 1000 mm Control Siemens Fabr. Touchscreen Mechanical. Accessories: Length: 2000 mm, Høhe: 1700 m0, Width: 3100 mm, Weight: 2600 kg
used
working width: 2520 mm for sheets up to: 2.5 mm Opening width upper cheek: approx. 250 mm Adjustability bending cheek: 30 mm Upper cheek drive: 1.5 kW Lower cheek drive: 2.3 kW electr. Connection: 380 V kW Weight: 2300 kg Space requirement: 3300 x 1400 x 1430 mm
used
SCHRÖDER DM-500 ID.NO. 2117 Schröder DM-500 brine mixer with mixer and pusher that goes up and down. Dimensions 135 x 135 cm H 180 cm. Available 4x in stock.
used
Type: N 50 Number of needles: 50 Diameter of needles: 4,0 mm Max. product width: 350 mm Transportation type: walking beam Product passage height: max 180 mm Brine pressure: 0,5 - 4,0 bar Machine dimensions in mm: Width: 800,0 Length: 1600,0 Height: 1900,0 Power: 8,0 kW , 17 A Voltage: 380 V, 50Hz
used
Type: IMAX 520 Working with boneless meat Product width: 520 мм Cycles: 15 to 60 per minute Feed: max. 60 mm Product height: 130÷230 mm Number of needles: 200 (2 х 100), 4 мм Brine pressure: 0,5-4,5 bar Machine charging height: 1170 mm Compressed air: 6bar Voltage: 230/400 V, 50/60 Hz Connection: 10,0 kW ; 23 А Rotary brine filter DF 510 Machine dimensions in mm: Length: approx. 2100 Width: approx. 1350 (about 2500 mm with filter) Height: approx. 2300
used
Type: MAX 500 Max. product weight: 500 кg. Drum diameter: 1000 mm Machine dimensions in mm: Width: 1600,0 Lenght: 3100,0 (incl. loading trolley) Height : 2300,0 Unloading height: 750,0 mm. Vacuum pump: 40 m3/h Power: 4,0 kW Voltage: 3х400 V, 50 Hz, 8,0 A Weight: 760 кg.
used
Type: : Schröder N 138 Number of needles: 138 Diameter of needles: 4,0 mm Product width: 620 mm Transportation type: walking beam Product passage height: 200 mm Brine pressure: 0,5 – 4,0 bar Machine dimensions in cm: Width: 110,0 Length: 220,0 Height: 230,0 Power: 10,0 kW Voltage: 380 V, 50 Hz
used
Type: SCHRODER N 120 Number of needles: 120 Diameter of needles: 3 mm Product width: 620 mm Transportation type: walking beam Product passage height: 180 mm Brine pressure: 0,5 – 4,0 bar Machine dimensions in cm: Width: 120,0 Width with filter for brine: 200,0 Length: 220,0 Height: 225,0 Compressed air: 6,0 bar Power: 14,0 kW Voltage: 380 V, 50 Hz
used
Type: SCHRÖDER N 82 Number of needles: 82 Diameter of needles: 3 mm Product width: 420 mm Transportation type: walking beam Product passage height: 180 mm Brine pressure: 0,5 – 4,0 bar Machine dimensions in cm: Width: 110,0 Width with filter for brine: 200,0 Length: 210,0 Height: 200,0 Compressed air: 6bar Power: 9,0 kW, 15А Voltage: 380 V, 50 Hz
used
Dough dividing and moulding machine Make: SCHRÃ?DER Model: FORTUNA A-3 slot 30-piece set With 3 new casting plates -top obsolete -with warranty -Delivery: free house within Germany
used
Type: UTK 18 200-2a-2e Power: 2 X 11 kW + 1 X 7.5 of kW, 380 V, 50 Hz Perslucht: max 20-25 bar Weight: 4,000 kg YOM 1985 Scraped surface heat exchanger for heating, temperature holding and cooling of liquid, vegetable, high viscous and crystalline products. Previous used for heating, holding (volume ± 85 ltr) and with steam cooling of food products (sauces) and ammonia (NH3, 125 ltr., 17 bar,-20 ° C / 45 ° C). 2 independent ammonia system. Constant quality of the product, continuous running and inline cleaning system (CIP).
used
Dough knitting machine - Make: SCHNÖDER - Model: FORTUNA Automat Gr. 3 - With new working plate - Condition: Used, restored - Warranty: 6 months
used
Schroeder-Combinator / scraped surface heat exchanger technical details: capacity/ flow rate: 20-100 ltr/h against 12 bar engine power: 3,5 KW dimensions: length x with x higth : 170 x 43 x 85 cm weight ca.: 150 kg with this device you can go with: hight viscosity and lumpy food for heating, cooling, mixing and pumping
used
Opening height: 120mm, motor power: 0.75kW, length: 1600mm, width: 1000mm, height: 1700mm, weight: 350kg.
used
Compressed air supply: 4bar, power: 8.5kW.
used
Max. output: 1,2t/h, length: 2620mm, width: 1180mm, height: 1680mm, weight: 1t, with trolley.
used
Working width: 2500mm, bending capacity: 3mm, connected load: 5kVA, weight: 3.5t.
used
Scraped surface heat exchanger, 2 Cylinders, Top cylinder: diameter: 25cm, rotor: 22,8 cm Length: 120 cm surface: 0,94 m2 Bottom cylinder diameter 33.5 cm, rotor diameter 31.5 cm, length 140 cm surface: 1.47 m2. 2 x electric drive motor: Top: 11 kW, 23A - 50 Hz, bottom: 18.5 kW, 36A - 50 Hz
used
Description: Serial Number: 39000135 Working length: 2540mm Double motor drive for folding botom : 2 x 2,2kw Stroke of upper opening: 350 mm , Sheet thickness: 4 mm Stroke of clamping beam 350mm Folding botom adjustment: 80 mm Geometry of clamping beam: 48 ,º Blade of the lower beam, approx. 700 N/mm²'. Manual clamping system on the clamping beam (WZS020) Rated power: 6.5kva CE-registration weight approx.: 4,500 kg, Approx. Onsite Dimension. (l x w x h): 4,314 x 1,694 x 1,510 mm
used
sheet width: 3220 mm plate thickness: 3,0 mm ST thickness at Niro-steel: 2,0 mm daylight opening: OW 300 mm speed: OW 100 mm/sec adjustment: BW 80,0 mm speed: BW 120 Grad/sec back stop - adjustable: k.A. mm speed: HA 300 mm/sec compressed air: 6,0 bar work height max.: 869 mm total power requirement: 8,8 kW voltage: 400 V weight: 5600 kg range L-W-H: 4575 x 2450 x 1737 mm current new price ~ 220.000 euros from a maintenance workshop Furnishing: - motorized universal folding machine High-precision mechanics with modern control technology for individual and series production Robust high-speed runner with high axis speeds Torsion-free welded construction - rotating upper beam / as an automatic tool changing system with 2x tool stations (sharp and goats foot bending rail) Reduces setup and idle times Saves time-consuming tool changes and adjustments - SCHRÖDER CNC control model POS ...
used
sheet width: 2020 mm plate thickness: 2.0 mm ST thickness at Niro-steel: 1.25 mm bending angle max.: 135 ° stroke of upper beam: 120 mm adjustment: UW 25.0 mm Control: CFB 120 voltage: 400 V total power requirement: 2.0 kW weight of the machine ca.: 1410 kg. dimensions of the machine ca.: 2930 x 2200 x 1175 mm new condition () New price at the time including accessories was approx. 35.000 euros Special price on request SCHRÖDER bending beam drive enables high forces and moments Efficiency. This means significantly reduced drive power lower energy consumption, but with increasing speed and Running - dynamics. The upper beam drive designed in the middle enables balanced torque distribution across the entire drive unit. The completely closed drive and guide units almost maintenance and wear-free operation. The regulation of the individual Drive axles are basically with a high quality p ...
used
sheet width: 4020 mm plate thickness: 4,00 mm distance between columns: mm upper beam stroke: 400 mm Lowering of bending & lower beam: 80 mm rated capacity: 12,0 kVA total power requirement: kW weight of the machine ca.: 10,25 t dimensions of the machine ca.: m - Bending beam drive on both sides - Ball screws on the upper beam - Manual crowning device for bending beam - Motorized bending beam adjustment program-controlled - Motorized lower beam adjustment program-controlled - Back gauge 1500 mm can be lowered pneumatically - Graphics control POS 2000 (display control recently renewed) - Sharpening rails 30° and 45° - Bending rail 20 mm The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.