We use cookies to optimize our website for you and to be able to continuously improve it. By continuing to browse the site you are agreeing to our use of cookies.
Disagree
used
Cellar Extraction blowers 1.8kW
used
Keller SMM 016,0 Extraction blowers Diameter 160/160mm Air flow rate 1200 Nm³/h 1.5kW
used
Cellar SMM 012.0 Extraction blowers Diameter 120/120mm Air flow rate 700 Nm³/h 0.55kW
used
Stroke length of the ram min. 120 mm .max. 320 mm Table diameter 630 mm Machine dimensions 2.45 m / 1.81 m / 2.89 m Machine weight 5,2 t
used
Description: Machine number: 502485 Operating voltage: 400 V Frequency: 50 Hz Connection: 5.5 kW Approx. Onsite Dimension. (l x w x h): 1,400 x 1,200 x 2,000 mm, weight approx.: 500 kg
used
Two-roll corrugating machine - crimper, for the production of polyester staple fibers, manufactured by KELLER (USA) by order of KOBE STEEL (Japan). The width of the work rolls is 150 mm. It is equipped with a clamping pneumatic cylinder and a drive gearbox manufactured by SEISA REDUCTION GEARS with a capacity of 150 kW. Productivity is up to 50 tons / hour. Made of AISI 304 stainless steel. 4 pieces are available. The equipment was practically not used - an operating time of about 60 hours.
used
Single screw degassing extruder CFE-699-A-04 for polymers manufactured by KELLER (USA) and KOBE STEEL (Japan) under a DUPONT license. The extruder has the following parameters: Overall dimensions of the extruder, taking into account the gearbox and motor - length 12 meters, width -2.5 meters, height -1.5 meters, the total diameter of the casing with a heating-cooling jacket is 950 mm, the diameter of the screw is 600 mm, screw length -7800 mm. The average screw speed is 22-25 rpm. The total weight of the extruder without spare parts is 40 tons. The working pressure in the casing is up to 300 bar, the working temperature of heating the melt is up to 300 degrees. The casing of the extruder is heated by high temperature oil supplied to it. The average productivity of polymers is 50-100 tons per hour. The extruder is equipped with a parallel reducer of POWER-TECH INTERNATIONAL (FOOT-JONES) ...
used
Type: Vario T 1.0 L originates from LVD lasercutting machine power: 2,2 kW
used
Technical data Spindle speeds: 1800 rpm Aspirated air: 20 m3/min Voltage 50 Hz 3x: 400 Volt Driving motor (motor power): 1.1 kW Power: 2.7 A Weight: 100 kg Dimensions: Length: 800 mm Width: 550 mm Height: 1100 mm
used
Capacity (x): 0 Process Application: 0 Other Info: 0 Technical data Spindle speeds: 2850 rpm Aspirated air: 1000 m3/h Voltage 50 Hz 3x: 400 Volt Driving motor (motor power): 1.5 kW Dimensions: Length: 1200 mm Width: 800 mm Height: 2300 mm
used
Capacity (x): 0 Process Application: 0 Other Info: 0 Technical data Voltage 50 Hz 3x: 400 Volt Installed power: 0.55 kW Weight: 60 kg Dimensions: Length: 650 mm Width: 500 mm Height: 1100 mm
used
sheet width: 480 mm plate thickness: 3 mm stations: 13 total power requirement: kW weight of the machine ca.: 11 t dimensions of the machine ca.: 15,x2 m Number of stations 13 Number of straightening stations 1 Waves 60 mm Center distance, horizontal 310 mm Center distance, vertical 110 - 250 mm Speed approx. 11 m / min. Connected load approx. 20 kW Uncoiler (without drive) - Coil- , inside 508/610 mm - Coil weight 3 t Flying hydraulic scissors Roller set for hat profile The techn. Data is manufacturer or operator information and therefore for us not binding. We reserve the right to make an interim sale, it applies exclusively our business and conditions of sale. The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.