GABLER used machine for sale

Motorized Film Indexing Max. Film width 805 mm Double Heating:Top Heater 81.90 kW Lower Heater 54.60 kWGabler M92XL Thermoformer, age 2009, with Cup Mold for Ø95mm PP Cups, Sheet Sag Control Max. Form Area 765 x 436 mm Indramat Servomotor Plug Assist Max. Depth of draw 150 mm (optional 200 mm) Clamping pressure 380 kN Motor Drive Rating 81.90 kW Air Pressure 6 - 10 bar Max. dry cycle speed 52/ minGabler M92XL Thermoformer, age 2009, with Cup Mold for Ø95mm PP Cups, Bottom Platten with Tilting movement Inline Counter/ Stacker Unit Counted products delivered to delivery conveyor at 90degs. to machine direction Suitable for PS, PP, PVC, ABS, PLA, PET etc. Siemens S7 PLC Controls Siemens SIMATIC MULTI PANEL Touchpad Display Inclusive of PP Cup Mold for Ø95mm PP Cups, 22-Cavity and associated Stacking Parts

M. No.: 3284 Equipment / Additional information: (min.) material thickness: 0.65 mm (max.) material thickness: 2 mm Technical Data: Width of film, max./min. 450/350 mm Forming area max. 430 x 160 mm Drawing depth max. negative/positive 6/20 mm (on request 22 mm negative) Top heater max. 10,15 kW Driving motors 3,0 kW Total connected load at 100 % duty cycle 12,7 kW Working air pressure 6 bar Air consumption (dependent on product) max. 1250 I/min Rate of water flow max. 1,0 m3/h COMPACT AND ROBUST - giving continuous high output. Easy and ergonomical operation (e.g. take- off height 1300 mm). QUICKLY CHANGEOVER - from 30° to 90° foil feed giving maximum material utilisation for both square and round lids. Heater changeover problem-free. PRECISION - The accuracy of the form table movement is guaranteed by linear guide bearings and hardened rods. The safe ...

Gabler D600 Thermoformer, age 2000:- Unwind Stand Indramat Servomotor Indexing. Top & Bottom Heaters, total Capacity 73.9 kW Indramat Servomotor Forming Station Forming area: 600 x 320 mm Depth of draw neg./pos.: 40/15 mm Stacking and counting Station Counted/ Stacked Products transferred automatically to Delivery Conveyor Waste Material Winder Main Machine PLC Controller: Siemens SIMATIC S5 P3 3A Heater PLC Controller: Siemens SIMATIC S5 95U Operator Touch Pad Control Panel (OPC) : Siemens SIMATIC OP27 Machine has been refurbished in 2014, New set of Cams added during Refurbishment. Excellent Production Condition

Forming surface: 750x436mm, heating output: 155kW, max. compressed air supply: 10bar, weight: 9.2t, operational hours counter: 43,589h.

SWING thermoforming machine with preheating station 2heat (using a complete 8-socket mold with a stacking device for manufacturing PP-stack.) Complete thermoforming machine SWING, made in GABLER Thermoform GmbH & Co., 2014 Designed for the manufacture of plastic cups of PP, PS, PET, HIPS and other thermoforming polymers using cutting punch (molding and cutting down together). Manufacturer: GABLER Thermoform GmbH & Co., Germany. Date of acceptance to accounting: 04/30/2014. Main technical characteristics: Area of forming surface, mm Maximum - 450x220 Minimum - 430x180 Maximum width of the tape, mm 480 Maximum tape thickness, mm 2 Maximum depth of molding, mm 125 Maximum noise level, dB Not more than 80 Tact at idle, tact / min 44 Mechanical performance, cycles / min 21-25 Voltage 230 / 400V, 50Hz Total power consumption, kW 64.15 Operating air pressure, bar 8 Dimensions (l ...

The thermoforming machine is designed for producing deep-drawn formed parts using heated plastic film. The machine features a controlled unwinder to feed the plastic film from a roll and a toothed conveyor belt for automatic transportation through the machine. The film is heated from above and below in the heating station, then vacuumed and compressed air is used to pull it into a mold for deep-drawing. After cooling, the outer contours are trimmed, and the individual blanks are held in place by retaining collars. In the stacking station, the product blanks are pressed out of the film and stacked on a conveyor belt, which transports them out of the machine once a set amount is reached. The entire process is automated based on programmed specifications, except for the manual removal of finished workpieces at the outlet. The trimming and stacking stations can be adjusted for different prod ...

Material : PP, PET, HIPS // Forming Area (Vxh): 800x550