We use cookies to optimize our website for you and to be able to continuously improve it. By continuing to browse the site you are agreeing to our use of cookies.
Disagree
used
Mill, Used Machine Type : B 315 Manufacturer : Alpine
used
Mill, Use Machine Type : B 315 U Manufacturer : Alpine Material : Mild steel
used
Mill, Used Machine Type : B 315 Manufacturer : Alpine
used
Alpine pin mill type 400 Z, burr disc diameter. 400 mm, 18.5 Kw. (engine not available)
used
Key data: 75 mm, 24
Blown film extruder for mono films TOP version Manufacturer Alpine BJ 1989 has already been partially modernized. Screw length 24d Screw diameter 75mm Blowing head BF 14-36 internal cooling from Alpine Cooling ring HK 300 with peak Output approx. 175 kg depending on the product Film thickness 12my – 50my Dosing Dosing unit with 4 volumetric feeders Winder Kuhne 1300mm Tandem Pre-treatment available 1 time Slotting device is available Flat laying 840mm – 1200mm Thickness measurement is available
used
old, but very good Alpine A 250 B mill, drive: 5.5 Kw., mounted on frame, with motor circuit breaker, ready for use. old, but very nice Alpine A 250 B Mill, motor 5.5 Kw., frame mounted, ready for use
used
Kolloplex pin mill type 630 Z, Drive : 55 KW Weight : 1100 kg; --> Stifscheiben diameter housing and door side : 630 mm;
used
Used mill Alpine 500.
used
Stock # U2333-5 Used cutting mill by Alpine model B32/40 RO. Mill has dimensions of inlet into cutting chamber 400 mm x 355 mm. Rotor is equipped with three knives and has diameter 315 mm x length 400 mm. Working rotation of rotor up to 700 rpm. Mill has 3 static knives. Bottom discharge through screen with mesh about 12 mm. Rotor is belt driven by el. motor with power 18.5 kW, 1500 rpm, 400 V, 50 hz. Mill has stainless steel feeding hopper with inlet dimensions: 390 mm x 240 mm. Mill is equipped with two belt conveyers. First feeding material into mill, has width of belt 250 mm, with baffles each 675 mm. Working length of conveyer 290 cm. Top of conveyer is covered with insulation. Second conveyer is for transport product from mill discharge - also has working width 250 mm, with baffles each 675 mm. Working length 200 cm. Mill has also dust filter with exhaust fan and electric contro ...
used
Used hammer mill made by Alpine, type B 630. Manufacturer's documentation.
used
used
--> Grinding blades in the opposite direction. Suitable--> mill for the processing of spices. 2 drives: 15 KW + 7.5 KW.
used
Ultra fine grinding plant, consisting of: Fluid bed opposed jet mill Alpine 630 AFG (V total: 885 dm³, 10 bar shock pressure resistant, fold out classifier wheel), cyclone, 2 pcs. EX shutter valves, control cabinet and 4 pcs. product containers. Prior use: Toner production. Plant can be inspected in already dismantled state. Available for an additional charge: Dust filter Buehler PGFG 60/18 (39 m² filtering surface).
used
Fine grinding plant consisting of: Alpine 630 AFG fluidized bed counter-jet mill (V ges: 885 dm3, 10 bar pressure-shock-resistant, saerterrad fold-out), feed station, cyclone, 2 pcs. EX-protection valve, control cabinet and 4 pieces of product buckets. Previous use: Grinding of toner. The system can be inspected in a disassembled condition. Available at an additional cost: Dust filter Bühler PGFG 60/18 (39 m2 filter area).
used
Material: mild steel Drive: 45 KW Weight: 2000 kg Dimensions: 1500 x 1500 x 1600 mm
used
Drive: 30 KW
used
used
Weight: 70 kg 18,000 rpm
used
used
Material: Steel Engine: 37 kW Weight: 1,700 kg diameters: 10-60 (mikron) task: kg/h 1200-5000 Speed: max. min 1 2250 This machine is overhauled and like new. You can also get the entire system with all components.
used
Engine 18.5 kW Weight approx. 740 kg On basic frame. Very good condition, like new. This machines is overhauled and in very good condition. You can also get the entire system with all components.
Material: steel Engine 11 kW Very good condition. You can also get the entire system with all components.
used
Machine in the very good condition, renewed and ready to use. We can offer to you drive and frame specially for your application. You can also get the entire system with all components.
used
Material: steel Engine: 75 kW Pin-disk Capasity factor: F=ca. 6,3 Drive: 75 kw Speed: 4900 The machine is as good as new. You can also get the entire system with all components.
used
Material: stainless steel Weight: 900 kg Dedusting filter Surface 31,2 m² Accessories: blower, cell wheel air-lock. Very god condition! You can also get the entire system with all components.
used
Weight 1750 kg Length x Width x Height 1800 mm x 1350 mm x 3000 mm Machine data: rotor diameter - knife circle : 500 mm length rotor : 630 mm angular speed rotor : appr. 650 min-1 after-run duration : appr. 60 sec. motor power - depent of order: 37 kW / 1500 min-1 45 kW / 1500 min-1 idle power :appr. 30 - 40 % of nominal power. Very good condition, ready to work. You can also get the entire system with all components.
used
General SKUR0378 LocationBarneveld MakeAlpine Ultraplex Type500 UP beater plate No.135101 Year of construction1966 Main Features Motor30 KW Inlet diameter450 mm Width150 mm Specified Features - Fine Impact Mill MaterialMild steel Fine Impact Mills Grindercheck Grinding room sizedia. 450x150mm Inlet170x100mm Motor30 kW 380/660 Volt Speed4500 rpm Information Total height1,1 M Weight600 kg Floorspace1,0x0,9 MFine Impact MillsAlpineMills > Fine Impact MillsBrand > Alpine What you can expect from Foeth: -- Machine is in working condition -- At a reduced price compared to new -- Ready for shipping to any destination worldwide -- You are welcome to inspect the machine in Barneveld, The Netherlands. Please visit us in Barneveld for many more machines!
used
General SKU104X554 LocationBarneveld MakeAlpine TypeK-15L No.368 Year of construction1985 Main Features MaterialStainless steel Volume15 Ltr. Motor0.55 KW Specified Features - Ribbon blender Ribbon blenderTruncated cone mixer (1x) Capacity15 Ltr Trough sizesdia. 345x280 mm With covercheck Motor0,55 KW, 220/380 Volt, 1405 rpm With variable speed drivecheck Speed mixing shaft22-130 Rpm MaterialStainless steel Information Mounted on framecheck Manually operated pan lifting With switchcheck Floor space1,7x0,6 M Total height1,6 M Weight120 KGRibbon blendersAlpineMixers > Ribbon blendersBrand > Alpine What you can expect from Foeth: -- Machine is in working condition -- At a reduced price compared to new -- Ready for shipping to any destination worldwide -- You are welcome to inspect the machine in Barneveld, The Netherlands. Please visit us in Barneveld for many more ...
used
General SKU171M709 LocationBarneveld MakeAlpine TypeKM 20 No.1607/15D Main Features MaterialStainless steel Volume2000 Ltr. Motor24 KW Specified Features - Ribbon blender Ribbon blender(1x) Truncated cone mixer Useful capacity2000 Ltr. Trough sizesDia. 1800x1800 mm Inlet1x320 mm, 1x200 mm, 3x80 mm, 1x25 mm Manholedia. 480 mm Outletdia. 150 mm (with ball valve) Motor24 Kw, 1475 rpm, 500 Volt, Exe II Speed mixing shaft30 rpm MaterialStainless steel Information Total height4 M (including legs)Ribbon blendersAlpineMixers > Ribbon blendersBrand > Alpine What you can expect from Foeth: -- Machine is in working condition -- At a reduced price compared to new -- Ready for shipping to any destination worldwide -- You are welcome to inspect the machine in Barneveld, The Netherlands. Please visit us in Barneveld for many more machines!
used
General SKU244U283 LocationBarneveld MakeAlpine TypeRO 28/40 No.3540/1 Year of construction1987 Main Features Motor15 KW Specified Features - Granulator MaterialSilicon steel 1.5023 Granulatorcheck Rotor width390 mm Rotor diameter300 mm Open rotorcheck Number of rotor knives3 Number of stator knives:2 Without hoppercheck Inlet410x285 mm Motor15 kW 380/660 Volt Rotor speed± 915 rpm Information Mounted on framecheck With switchcheck (as is) Weight650 kg Floorspace1,3x0,8 m Total height1,5 mGranulatorsAlpineMills > GranulatorsBrand > Alpine What you can expect from Foeth: -- Machine is in working condition -- At a reduced price compared to new -- Ready for shipping to any destination worldwide -- You are welcome to inspect the machine in Barneveld, The Netherlands. Please visit us in Barneveld for many more machines!