used ABS SCHWABE AH

Decoiler double reel double lab winding reel model AHMD2.0H Manufacturer: ABS Schwabe Germany. It's a demonstration machine: Bandwidth at 1.5 t = 600 mm Bandwidth at 2.0 T = 400 mm The reel with the corresponding coil weight may be charged depending on the bandwidth. -Stable base frame in welded bolt steel - shooting wreath storage with pneumatic locking - procedures establishment with crank spindle for band-middle-centering -Hydraulic spread with hand pump, can be converted to electric hydraulic -Spreader range 350-600 mm -Thornless version for free loading with ABS-Patent-Expansion vertically from behind about 3 hydraulic cylinders with mechanical forced centering -Drive gear motors that control drive with infinitely variable speed control Dancer position control with self-learning control Siemens PLC controller Lenze, KME or Siemens

New decoiler with hydraulic spread: Capacity 3.0 Tons at 400 mm bandwidth Capacity 2.75 Tons at 650 mm bandwidth Capacity 2.75 Tons at 750 mm bandwidth Mandrel shaft height 1200 mm Coil-Outside Diamter 1500 mm Spreader range 450-600 mm Hydraulic spread with hand pump, optional electric pump. ABS patent spread over 3 hydraulic cylinders Options : pneumatic pressure arm, mouvable basement, brackets for round coil clamping The here given price is for standard version with electronic variable speed control, Ultrasonic-loop-control with selve-learning reel-calculater, Siemens SPS, drive Lenze or Siemens. The decoiler is on stock, the brackets will be produced belong to the needed bandwidth. Delivery-time is about 6 weeks

New unwinding reel with hydraulic spread: Payload 2.0 tons at 300 mm bandwidth Payload 1.8 tons at 450 mm bandwidth Payload 1.6 tons at 600 mm bandwidth Spine height 1410 mm Coil outer mennesser 1500 mm Spreading range 300-600 mm Hydraulic spread with hand pump, optional lyrify can be retrofitted ABS patent spread over 3 hydrocylinders with continuous eccentric. This reel is stocked in stock. The spreadjaws currently have a length of 600 mm. The price given here applies to : basic version but without push arm, hydro unit, manual hand pump. Delivery time: immediately from stock, intermediate sale reserved Control: Constant drive or control drive with loop control, initiator or ultrasonic for infinitely variable speed control. Additional price 3000 - 5700 â?¬, depending on the version. Delivery time for the control: 3 - 4 weeks

Payload 1000 KG Bandwidth without/with back arm 500/470 mm Spreading range 440-600 mm Coil outer diameter 1300 mm, larger at extra cost Spine height 1200 mm System disc thickness 10 mm ABS unwinding reel with special construction features: - NEW ! Preparation for flange mounting for other brakes and retrofitting for other drives - modular system - e.g. conversion to higher loads possible - Reel body made of stable welded construction, large stable stand column, rotary wreath bearing integrated in stable flange, 4 screw holes, corner stiffening at high loads - Coil side guide with system disc rear and system ring easily adjustable above quick-release lever, made of high-strength steel, depending on the version with corner stiffening - Bearing bushing with reel shaft made of high-quality steel, for the lowest deflection with maximum weight load - Shaft bearing 2-fo ...

Compressive force 10 tons, front shaft on the flywheel - Machine frame made of steel, in the Base with insulation material in the hollow body - Shaft made of alloy steel - Pneumatic brake clutch combination - Pneumatic system consists of Pressure accumulator, pressesSafety valve, filter, Double-block solenoid valve with dynamic control, pressure switch - Automatic central lubrication with adjustable oil dosing - mechanical cam switchgear with brake angle display - Protective devices made of aluminium profile, fully electrically protected - Control with PLC and PILZ safety module - Welded steel plunger with oil recovery plate (only T10 standard) - mechanical plunger release - mechanical cam switchgear with crank angle display - Programmable stroke counter - Two-hand operation and with Foot pedal only with the safety doors closed - Protective device made of aluminium p ...

Compressive force 20 tons, front shaft on the flywheel - Machine frame made of steel, in the Base with insulation material in the hollow body - Shaft made of alloy steel - Pneumatic brake clutch combination - Pneumatic system consists of Pressure accumulator, pressesSafety valve, filter, Double-block solenoid valve with dynamic control, pressure switch - Automatic central lubrication with adjustable oil dosing - mechanical cam switchgear with brake angle display - Protective devices made of aluminium profile, fully electrically protected - Control with PLC and PILZ safety module - Welded steel plunger with oil recovery plate (only T10 standard) - mechanical plunger release - mechanical cam switchgear with crank angle display - Programmable stroke counter - Two-hand operation and with Foot pedal only with the safety doors closed - Protective device made of aluminium p ...

Compressive force 45 tons, transverse shaft on the flywheel - Machine frame made of steel, in the base with insulation material in the hollow body - Shaft made of alloy steel - Pneumatic brake clutch combination - Pneumatic system consists of pressure accumulator, press safety valve, filter, Double-block solenoid valve with dynamic control, pressure switch - Automatic central lubrication with adjustable oil dosage - Hydraulic unlocking in case of overload - Weight balancing cylinder of the Pestle - Mechanical plunger release - Weight compensation cylinder of the Stö- ßels - mechanical cam switchgear with Brake angle indicator - Protective devices made of aluminium profile, fully electrically protected - Control with PLC and PILZ safety module - Programmable stroke counter - Two-hand operation and with foot pedal only when the safety doors are closed - Protective de ...

Compressive force 55 tons, transverse shaft on flywheel - Machine frame made of steel, Im Base with insulation material in the hollow body - Shaft made of alloy steel, shafts made of steel in an oil bath - Pneumatic brake clutch combination - Pneumatic system consists of Pressure accumulator, pressesSafety valve, filter, Double-block solenoid valve with dynamic control, pressure switch - Automatic central lubrication with adjustable oil dosage - hydraulic unlocking at Overload - Weight balancing cylinder of the Pestle - Mechanical plunger release + adjustment - Pre-lay gears in the oil bath - mechanical cam switchgear with brake angle display - Protective devices made of aluminium profile with Plexiglas, completely closed with 2 hinged doors, electric secured - Control with PLC and PILZ safety module - Programmable stroke counter - Two-hand operation and with foot  ...

Compressive force 80 tons, transverse shaft on flywheel with wheel attachment - Machine frame made of steel, Im Base with insulation material in the hollow body - Shaft made of alloy steel, shafts made of steel in an oil bath - Pneumatic brake clutch combination - Pneumatic system consists of Pressure accumulator, pressesSafety valve, filter, Double-block solenoid valve with dynamic control, pressure switch - Automatic central lubrication with adjustable oil dosage - hydraulic unlocking at Overload - Weight balancing cylinder of the Pestle - Mechanical plunger release + adjustment - Pre-lay gears in the oil bath - mechanical cam switchgear with brake angle display - Protective devices made of aluminium profile with Plexiglas, completely closed with 2 hinged doors, electric secured - Control with PLC and PILZ safety module - Programmable stroke counter - Two-hand op ...

Compressive force 105 tons, transverse shaft on flywheel with wheel attachment - Machine frame made of steel, Im Base with insulation material in the hollow body - Shaft made of alloy steel, shafts made of steel in an oil bath - Pneumatic brake clutch combination - Pneumatic system consists of Pressure accumulator, pressesSafety valve, filter, Double-block solenoid valve with dynamic control, pressure switch - Automatic central lubrication with adjustable oil dosage - hydraulic unlocking at Overload - Weight balancing cylinder of the Pestle - Mechanical plunger release + adjustment - Pre-lay gears in the oil bath - mechanical cam switchgear with brake angle display - Protective devices made of aluminium profile with Plexiglas, completely closed with 2 hinged doors, electric secured - Control with PLC and PILZ safety module - Programmable stroke counter - Two-hand o ...

Compressive force 130 tons, transverse shaft on flywheel with wheel attachment - Machine frame made of steel, Im Base with insulation material in the hollow body - Shaft made of alloy steel, shafts made of steel in an oil bath - Pneumatic brake clutch combination - Pneumatic system consists of Pressure accumulator, pressesSafety valve, filter, Double-block solenoid valve with dynamic control, pressure switch - Automatic central lubrication with adjustable oil dosage - hydraulic unlocking at Overload - Weight balancing cylinder of the Pestle - Mechanical plunger release + adjustment - Pre-lay gears in the oil bath - mechanical cam switchgear with brake angle display - Protective devices made of aluminium profile with Plexiglas, completely closed with 2 hinged doors, electric secured - Control with PLC and PILZ safety module - Programmable stroke counter - Two-hand o ...

new decoiler recoiler with mechanical expansion,stabilzed design, protection ring. option: Pressure arm, loop control, ultrasonic loops, hydr. expansion,decoiler mouvable Coilweight max. 150 kg bandwidth max. 150 mm Expasion range 365-565 mm Coilaussendurchmesser 800 mm, optionally greater extra charge 200 mm each step 590.-€ shaft height 1000 mm speed 17.5/min consistently standard, variable optionally Motor-Power 0.18KW 400V50Hz control Consistently: Hand/Auto, hand switching right/left, time delay for start loop control with initiator extra price 1580.-€ control incl. ultra sound automatic infinitely variable adjustably extra price 2980.-€ delivery time: at the moment 6-8 weeks given price is for a 150-kg driven decoiler (Changes and mistakes in the technical data, information and Price is reserved)

Bandwidth 310 mm (For BFZD 260+-25 mm) Coil thickness 400/800 N/mm2 0.4-4.0 mm Full-width tape thickness at 400/800N/mm2 3.0/2.0 mm Roller diameter under roller 90 mm Roller diameter upper roller 75 mm Contact force of the upper roller max. 2.35 KN Speed according to ABS calculation program Connection voltage 400 V50Hz Control voltage 24 VDC through-run height according to customer specifications, but only when ordering a separate Underframes for an additional price, as standard is loose for building Delivered. No summation tolerances for follow-up steps. The speed depends of belt loop weight, crank angle and belt cross-section and is best case. - Roller feed in a stable plate construction made of high-quality steel precision-made - Rollers in high-performance cylinder roller bearings, hardened, ground, hollow rollers for low Inertia - Upper roller with precision guide  ...

Bandwidth 210 mm Tape thickness 0.2-4.0 mm Full-width tape thickness at 400N/mm2 3.0 mm Upper roller diameter 80 mm Underroll diameter 80 mm Speed according to ABS calculation program Connection voltage 400 V50Hz Control voltage 24 VDC Pass height according to customer specifications, but only when ordering a separate base for additional price, as standard is delivered loosely for on-site attachment. No summation tolerances for follow-up steps. The speed depends on the belt loop weight, crank angle and belt cross-section and is achieved in the most favorable case. - Roller feed in a stable plate construction made of high-quality steel precision-made - Steel rollers hardened, ground, ball bearings, hollow rollers for low mass inertia - Upper roller in steel frame with lateral cast iron guide plates, adjustable guide strips spring-loaded, ...

Bandwidth 310 mm Tape thickness 0.2-4.0 mm Full-width tape thickness at 400N/mm2 3.0 mm Upper roller diameter 80 mm Underroll diameter 80 mm Speed according to ABS calculation program Connection voltage 400 V50Hz Control voltage 24 VDC Pass height according to customer specifications, but only when ordering a separate base for additional price, as standard is delivered loosely for on-site attachment. No summation tolerances for follow-up steps. The speed depends on the belt loop weight, crank angle and belt cross-section and is achieved in the most favorable case. - Roller feed in a stable plate construction made of high-quality steel precision-made - Steel rollers hardened, ground, ball bearings, hollow rollers for low mass inertia - Upper roller in steel frame with lateral cast iron guide plates, adjustable guide strips spring-loaded, ...

Bandwidth 90 mm Feed length 0-510 mm Tape thickness 0.12-2.0 mm, belt cross-section max. Stroke capacity max. 72-140/min* Air consumption / double stroke 7 L VL 510 mm Clamping force Retaining pliers at 7 bar 1375 N Clamping force feed pliers at 7 bar 1375 N Feed force at 7 bar 484 N Feed tolerance +-0.05 mm * Stroke number unloaded,max. Feed length, with a smaller feed length, the stroke number increases Accordingly Max pressure 8 bar,the forces increase accordingly ABS pliers with special design features : clamping pliers from above, integrated solenoid valve technology, integrated electronic feed end query, adjustable End position damping, retractable feed stop, mounted roller basket with Tape side guides and height adjustment, expandable bandwidths due to attachment kits at any time Can be retrofitted afterwards, optionally separate air pressure adjustment for clampin ...

Bandwidth 102 mm Feed length 0-102 mm Tape thickness 0.2-2.0 mm Stroke number max. 80 /min* Air consumption max. 192 L/min Clamping force Retaining pliers at 7 bar 1360 N Clamping force feed pliers at 7 bar 770 N Feed force at 7 bar 205 N Feed tolerance +-0.05 mm * Stroke number unloaded,max. feed length, with a smaller feed length, the stroke number increases accordingly Max.pressure 8 bar,the forces increase accordingly ABS pliers with special design features such as clamping pliers from above, resteering technology for use as pulling or sliding device : - Compact design, designed for great performance in the smallest space - Basic housing made of high-strength aluminium, precision-engineered, precision cylinder tube for feed pistons, interchangeable - Feed alumi ...

Load max. channel 20Kg,parts 40 Kg=Ges 60 Kg Pressure 3.5-8 bar Air consumption at 6 bar approx.3.8 l/min Control pneum. Feed speed 8-15 m/min Stroke length max. 55 mm Stroke frequency min./max. 40/180 h/min. Noise level without gutter approx.50 db/A) Air connection 3/8 G Device width without base plate 122 mm Device width with base plate 160 mm Geraete height without base plate 60 mm Device height with base plate 65 mm Device length without stroke 290 mm Weight 4.5 Kg Operating temperature* 70 °C * 200 °C max. auf Anfrage NEU*NEU*NEU*NEU*NEU*NEU*NEU*NEU*NEU*NEU*NEU Developed for multi-layer hard continuous use with the new special ABS-PATENT: - no steel springs, fully pneum.controlled, thus maintaining the same power distribution for forward and back  ...

Latest development ! HIGH SPEED SERIES ! Very fast transport of the components ! Very robust technique as known ! Load max. channel 15Kg, parts 25 Kg=Ges 40 kg Pressure 3.5-8 bar Air consumption at 6 bar approx.2.1 l/min Control pneum. Feed speed 8-30 m/min Stroke length max. 35 mm Stroke frequency min./max. 290/740 h/min. Noise level without gutter approx.50 db/A) Air connection 3/8 G Device width without base plate 122 mm Device width with base plate 160 mm Device height without base plate 60 mm Device height with base plate 65 mm Device length with valve body without stroke 270 mm without valve body 232 mm Weight 6.3 Kg Operating temperature* 70 °C â?¢ Achieved in the best case: gradient, friction, dry parts * 200 °C max. auf Anfrage NEU*NE ...

Our robust device as well known for multi-layer continuous use ! Load max. channel 8 Kg,parts 12 Kg=Ges. 20 Kg Pressure 3.5-8 bar Air consumption at 6 bar approx.0.5 l/min Control pneum. Feed speed 8-10 m/min Stroke length max. 35 mm Stroke frequency min./max. 40/240 h/min. Noise level without gutter approx.70 db/A) Air connection 3/8 G Device width without base plate 78 mm Device width with base plate 125 mm Geraete height without base plate 40.5 mm Device height with base plate 46.5 mm Device length without stroke 212 mm Weight 1.5 Kg Operating temperature* 70 °C â?¢ Achieved in the best case: gradient, friction, dry parts * 200 °C max. auf Anfrage NEU*NEU*NEU*NEU*NEU*NEU*NEU*NEU*NEU*NEU*NEU Developed for multi-layer hard continuous us ...

Our robust device for multi-layer continuous use ! Load max. channel 40Kg,parts 80 kg=Ges 120 kg Pressure 3.5-8 bar Air consumption at 6 bar approx.7.9 l/min Control pneum. Feed speed 8-15 m/min Stroke length max. 55 mm Stroke frequency min./max. 40/180 h/min. Noise level without gutter approx.50 db/A) Air connection 3/8 G Device width without base plate 244 mm Device width with base plate 284 mm Geraete height without base plate 75 mm Device height with base plate 85 mm Device length without stroke 305 mm Weight 15.5 Kg Operating temperature* max. 70 °C â?¢ Achieved in the best case: gradient, friction, dry parts * 200 °C max. auf Anfrage NEU*NEU*NEU*NEU*NEU*NEU*NEU*NEU*NEU*NEU*NEU Developed for multi-layer hard continuous use with the ...

Bandwidth 200mm Tape thickness max. 2.0 mm Tape cross-section max at 400N/mm2 340 mm2 Cutting speed approx. 96 /min Drive power 1.5 KW Tape inlet height 290-940 mm Scissor width x depth 380 x 475 mm Connection voltage zero + 3 x 400 V/50Hz Translation 15 i Engine speed 1420 rpm ABS separating shredder in very stable design for bar-independent cutting/crushing of belt material and die-cutting grid with minimum set-up times: -robust motor drive with gear ratio, thus high torque for long service life -rotating wing and fixed counter knife made of tough tool steel with special coating, hardened, ground -fixed knife adjustable and 4-fold usable, deliverable via pressure screws -Eccentric in double ball bearing, eccentric plate side-supported with 2 heavy-duty support roller bearings -4 guide plates hardened, interchangeable, with oil grooves -automatic lubrication of the ecce ...

Bandwidth 250 mm Tape thickness max at 400 N/mm2 2.0 mm Tape cross-section max at 400 N/mm2 340 mm2 Cutting speed up to 362 rpm possible depending on the drive Wedge angle upper knife 83° Cutting angle Roof cut 3.0° free crank angle 220° Knife-free stroke height max. 31 mm Tape inlet height 630-1690 mm (minimum height incl. collection container height 300 mm) Scissor width x depth approx. 670 x 570 mm Connection voltage zero + 3 x 400 V/50Hz Lower knife with wedge angle 83° Inlet inclination angle adjustable via screw holes max. approx. 31° ABS separating shredder in very stable design for tact-independent crushing of tape material and die-cutting grille with minimum set-up times: - robust geared motor KEB, high torque, maintenance-free - stable knife beam on 2 linear guides - Upper knife in roof cutting technology, ...

Bandwidth max. 135 mm Tape thickness 1.0 - 3.6 mm, depending on material strength Compressive force at 7 bar to 66 KN, depending on the design 2 - 12 pcs. cylinders single or double-row each 80 - 100 mm, depending on the output Wedge angle 83° Stroke number unloaded approx. 90 - 300 strokes/min, depending on the design Opening between the knives approx. 3 - 6 mm Cutting angle 3.0° Solenoid valve 5/2 24VDC Very stable ABS patent construction with roof cut for mounting on the press table or a mounting angle. Due to the roof cut only half stroke, lower air consumption, very fast stroke numbers : - Frame in modular plate construction with stable base plate and long bores, very compact construction - 2 upper knives made of high-quality tool steel, hardened, ground, resandable, screwed in cast iron knife beams in roof cut arrangement - Lower knife made of hig ...

Roller feed Bandwidth 310 mm (For BFZD 260+-25 mm) Coil thickness 400/800 N/mm2 0.4-4.0 mm Full-width tape thickness at 400/800N/mm2 3.0/2.0 mm Roller diameter under roller 90 mm Roller diameter upper roller 75 mm Contact force of the upper roller max. 2.35 KN Speed according to ABS calculation program Connection voltage 400 V50Hz Control voltage 24 VDC through-run height according to customer specifications, but only when ordering a separate Underframes for an additional price, as standard is loose for building Delivered. No summation tolerances for follow-up steps. The speed depends of belt loop weight, crank angle and belt cross-section and is best case. - Roller feed in a stable plate construction made of high-quality steel precision-made - Rollers in high-performance cylinder roller bearings, hardened, ground, hollow rollers for low Inertia - Upper roller with pre ...