mtu ba 500 used for sale

A used Miwe Aero 4.0604 / 4.0604 DUO in-store baking oven from 2019 is currently for sale and is immediately available from stock. In-store baking oven Miwe Aero 4.0604 DUO, two 4-seater ovens with separate controls on top of each other from 2019 for sale. The baking station is equipped with proofer and steam condenser and both ovens with Miwe FP 12 control. Convection oven Miwe Aero 4.0604 / 4.0604 Year: 2019 - 2 electric in-store baking ovens on top of each other - Manufacturer: Miwe - Model Aero AE 4.0604 / AE 4.0604 - both ovens for 4 trays each 60x40cm - with proofer - With Miwe FP12 control - With steam condenser - 17.4 kW - 400 /230 Volt 3/N/PE 50 Hz - Year of construction 2019 - Door hinge on the right - Outer dimensions approx. width 90cm

PLASTIC BAGS MAKING MACHINE VAMA VC 600 Germany made in 2015. Technical data Manufacturer: VAMA GmbH Model: VC 600 Production year: 2015 Technical parameters The width of the film maximum: 600 mm The maximum length of the bag: 1200 mm Film thickness: 25-80 μm weld Capacity: 60 - 90 bags per minute Rolling rollers 2 with roll diameter: 700 mm Stacking position: 25-50 pieces Machine for the production of plastic bags Excellent condition, located in Poland

Heavy-duty wheels, swivel castors, castors, solid rubber castors Outer diameter: 240 mm Bore: 30 mm Rubber thickness: 30 mm Quantity: 90 Sold as shown All information without guarantee

used baler Manufacturer: PAAL Type: LIKON 110/150 Year of construction: May 2004 Specifications: Press weight up to: approx. 36 tons Press force at 275 bar: 150 t Operating pressure max. 320 bar Filling opening: approx. 2,000 x 1,020 mm Channel cross-section: 1,100 x 1,100 mm Drive power: 2 x 75 kW Flow rate: 425 m³/h Binding: 5-fold horizontal Total connected load: 176 kW Rated current: 340 A Pre-fuse (min.) 400 A Operating voltage: 3 x 400 VAC/50 Hz/N/PE Control voltage: 230 VAC / 24 VDC including: - Oil cooling - Low-pressure circuit - Free kicks - Key locking system Transport dimensions: Length: 13,803 mm Width: 2,500 mm Height: 3,164 mm without wire unwinding devices, without binding wire, without feed belt, without a personal protection system, without conveyor belt hopper and withou ...

Good day We hereby offer you a used baler from the manufacturer Presona AB, type LP 80 VH1. The following technical data have been taken from the manufacturer's operating instructions and brochures, for which we cannot assume any liability for accuracy and completeness. Manufacturer Presona AB, Sweden Type LP 80 VH1 Year of manufacture 2007 Total operating hours, 21,676 hours, as of November 2024 Press force main press 78 t Specific pressing force 95 N/cm² Press force pre-press flap 28 t Dimensions of the insertion tray 1,500 x 1,100 mm Filling volume / pressing cycle 2.7 m³ Throughput under operating conditions 410 m³/hour Bale dimensions 1,100 x 750 mm Drive power 55 kW 5-fold vertical bonding Hydraulic oil tank volume 1,000 L Press dimensions built with hopper 10,985 x 3,750 x 4,310 mm (L x W x H) Machine weight press approx. 25 t Hint: The machine was u ...

The BTS-MF150 is the ideal waste baler for compacting your loose cardboard and plastic film waste into a bale of up to 150 kg. The baling press impresses with its ease of use, safe operation and its large filling volume, it is ideal for medium material volume. By baling these valuable and recyclable materials you achieve a volume reduction of up to 90%, a significant saving on your disposal costs and you properly return the material back into the recycling cycle. Pressing force: 8 Ton Bale weight: up to 150 kg (material depending) Bale size: 1000 H (var.) x 975 W x 800 D mm Machine size: 2630 H x 1560 W x 1030 D mm Machine weight: 780 kg Transport height: 1955 mm Loading aperture: 975 W x 470 H mm Cycle times: 40 seconds Motor: 2.2 kW 16 Amp Power supply: 220 - 240 V (1 phase) Noise level: 68 dB User-friendly lever control Bale kicker for easy eject the bal ...

cutting diameter: 320 mm saw band length: 3660x27x0,9 mm cutting width: 400 mm cutting capacity - flat: 400 x 220 / 90° mm cutting capacity - round: 320 /90° mm speed: 20 - 100 m/min cutting capacity - flat: 280 x 200 / 45° mm cutting capacity - round: 280 / 45° mm sawing motor: 1,5 kW hydraulic motor: 0,37 kW coolant pump: 0,12 kW total power requirement: 2 kW weight of the machine ca.: 670 kg dimensions of the machine ca.: 1800 x 850 x 1200 mm Accessories: • Inverter • hydraulical vice • automatical movement to the top via hydraulical cylinder. The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

The BTS-MF250 is the ideal waste baler for compacting your loose cardboard and plastic film waste into a bale of up to 250 kg. With a crush insert baler is even suitable for crushing individual small and large drums and also other sheet metal containers. The baling press impresses with its ease of use, safe operation and its large filling volume. By baling these valuable and recyclable materials you achieve a volume reduction of up to 90%, a significant saving on your disposal costs and you properly return the material back into the recycling cycle. Pressing force: 15 Ton Bale weight: up to 250 kg (material depending) Bale size: 1000 H (var.) x 1200 W x 800 D mm Machine size: 2900 H x 1759 W x 1185 D mm Machine weight: 985 kg Transport height: 2250 mm Loading aperture: 1200 W x 680 H mm Cycle times: 34 seconds Motor: 2.2 kW 16 Amp Power supply: 220 - 240 V (1 phas ...

: 36/72 m/min capacity 90 degrees: round: 300 mm capacity 90 degrees: square: 260 mm capacity 90 degrees: flat: 330x260 mm capacity 60 degrees: round: 180 mm capacity 60 degrees: square: 170 mm capacity 60 degrees: flat: 170x170 mm capacity 45 degrees: round: 260/200 mm capacity 45 degrees: square: 250/180 mm capacity 45 degrees: flat: 270x200/200x160 mm dimensions of saw-band: 3650x27x0,9 mm total power requirement: 1,5/1,8 kW Overall size: 2130x1400x1950 mm Weight: 670 kg Semi-automatic function: - Vice closes and engine starts - Saw head lowers for the cut - Engine shuts off - Saw head lifts, vice opens Semiautomatic dynamic system: Manual lowering of the saw blade to the desired position and cycle start over the hand switch. Upper position is saved automatically. The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

dimensions of saw-band: 3320x27x0,9 mm : 40/80 m/min : 335 mm capacity 90 degrees: round: 300 mm capacity 90 degrees: square: 260 mm capacity 90 degrees: flat: 330x260 mm : 260 mm : 250 : 270x200 mm capacity 60 degrees: round: 180 mm capacity 60 degrees: square: 170 mm capacity 60 degrees: flat: 170x170 mm : 200 mm : 180 mm : 200x160 mm weight of the machine ca.: 640 kg dimensions of the machine ca.: 2140x1300x1950 mm The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

dimensions of saw-band: 4640x34x1,1 mm : 15-100 m/min : 515 mm capacity 90 degrees: round: 330 mm capacity 90 degrees: square: 320 mm capacity 90 degrees: flat: 510x320 mm : 320 mm : 320 mm : 350x320 mm : 230 mm : 230 mm : 230x310 mm : 320 mm : 320 mm : 380x320 mm : 250 mm : 250 mm : 250x320 mm total power requirement: 4 kW Weight: 1190 kg Overall size: 2000x1200x1800 mm The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

: 25-138 m/min dimensions of saw-band: 1440x13x0,65 mm capacity 90 degrees: round: 150 mm capacity 90 degrees: square: 125 mm capacity 90 degrees: flat: 150x125 mm capacity 45 degrees: round: 75 mm capacity 45 degrees: square: 50 mm capacity 45 degrees: flat: 70x50 mm weight of the machine ca.: 35 kg Standard features: - right and left miter - Single-phase 1800 watt motor - Safety switch - Electronic rotary speed controller 25-138 m / min. with torque control The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

: 25-138 m/min dimensions of saw-band: 1440x13x0,65 mm capacity 90 degrees: round: 150 mm capacity 90 degrees: square: 125 mm capacity 90 degrees: flat: 150x125 mm capacity 45 degrees: round: 75 mm capacity 45 degrees: square: 50 mm capacity 45 degrees: flat: 70x50 mm weight of the machine ca.: 35 kg Standard features: - Single-phase 1800 watt motor - Safety switch - Electronic rotary speed controller 25-138 m / min. with torque control The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

dimensions of saw-band: 2085x20x0,9 mm capacity 90 degrees: round: 185 mm capacity 90 degrees: square: 150x150 mm capacity 90 degrees: flat: 220x150 mm : 110 mm : 100x100 mm : 110x90 mm capacity 60 degrees: round: 70 mm capacity 60 degrees: square: 70x70 mm capacity 60 degrees: flat: 70x70 mm voltage: 230 V sawband speed: 30-75 m/min. : 230 mm total power requirement: 2,35 kW weight of the machine ca.: 200 kg dimensions of the machine ca.: 1280x550x1480 mm Domestic equipments: - stepless, electronic speed control - Optional hydraulically controlled or manual belt arm lowering - Saw arm can be swiveled up to 60 ° right - quick release vice - Band guide with 8 ball bearings - Hydraulic saw blade clamping with clamping pressure display and strip break-off - Including coolant device - incl. machine cabinet The data for this ad was created with ModulMWS - the software solution of LogoTech  ...

workpiece weight: 4 kg workpiece length: 200 mm dia. on complete length: 200 mm Control: Schenck-Lauer electrics - voltage/frequency: 400 / 50 V/Hz dimensions: 4,1 x 4,2 x 2,5 m connected load: 12 kVA flange diameter: 250 mm weight: 4,5 t Balancing machine for rotors - Turbocharger fuselage groups - hydraulic measuring station - Compensation station - Pulsation measuring table - Chip extraction - Measuring instrument CAB 950T - feeding device - Schenck/Lauer Control on Dase of Windows The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

: 330 mm : 5000 mm : 450 mm : 330 mm : 450x330 mm dimensions of saw-band: 5000x34x1,1 mm The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Miwe FBC Backstation 6.0604 + 10.0604 Bj.2013 Double in-store baking oven electric Miwe FBC (Fresh Back Center) for sale Used Miwe FBC electric convection oven from 2013. There are two ovens on top of each other, one is for max. 10 trays of 60x40cm and the other for max. 6 trays of 60x40cm. The ovens are equipped with automatic cleaning. Easy operation thanks to Miwe FP control. - Type: FBC 6.0604 SV / 10.0604 - Year of construction: 2013 - With FP control - With extractor hood and fan - With steam destroyer including exhaust hood - with automatic cleaning - Door lock with PIN - With 1 loading trolley, optionally with more - 10 burner stove requires 19.7 kW - 6 burner requires 9.3 kW - 400/230V 3/N/PE 50 Hz

cutting diameter: 325 mm saw band length: 4380x34x1,1 mm cutting width: 450 mm cutting capacity - flat: 450 x 325 / 90° mm cutting capacity - round: 325 /90° mm speed: 20 - 100 m/min sawing motor: 2,2 kW total power requirement: 3 kW weight of the machine ca.: 1010 kg dimensions of the machine ca.: 2100 x 860 x 1500 mm Accessories: • Inverter • hydraulical vice • automatical movement to the top via hydraulical cylinder. The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

cutting diameter: 360 mm saw band length: 5200 x 34 x 1,1 mm cutting width: 700 mm cutting capacity - flat: 590 x 360 /30° mm cutting capacity - round: 360 / 30° mm cutting capacity - square: 360 x 360 / 30° mm cutting capacity - flat: 460 x 360 /45° mm cutting capacity - round: 360 /45° mm cutting capacity - square: 360 x 360 / 45° mm cutting capacity - flat: 305 x 360 /60° mm cutting capacity - round: 360 / 60° mm cutting capacity - square: 305 x 360 / 60° mm cutting capacity - flat: 700 x 360 / 90° mm cutting capacity - round: 360 / 90° mm cutting capacity - square: 360 x 360 / 90° mm speed: 20 - 100 m/min sawing motor: 3 kW hydraulic motor: 0,55 kW coolant pump: 0,12 kW voltage: 400 V / 50 Hz total power requirement: 3,7 kW weight of the machine ca.: 1460 kg dimensions of the machine ca.: 2850 x 1000 x 1850 mm Accessories: • Inverter • hydraulical vice • automatical ...

cutting diameter: 460 mm saw band length: 5200 x 41 x 1,3 mm cutting width: 460 mm cutting capacity - flat: 470 x 460 / 90° mm cutting capacity - round: 460 / 90° mm speed: 20 - 100 m/min voltage: 400 V / 50 Hz sawing motor: 4 kW total power requirement: 4,7 kW weight of the machine ca.: 1,665 t dimensions of the machine ca.: 2100 x 1300 x 850 m full-automatical band saw, Accessories: • Inverter for controllable speed, • automatical stop function after sawing and on breakage of the saw blade, • automatical saw arm lifting, • hydro-mechanical clamping of the saw blade, • material clamping to be effected from above, hydraulical vice, • switch for cutting pressure control, • coolant pump, • roller conveyor, length: 1.2 m. The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

throat: 1800 mm workpiece height: 750 mm Travel: 4000 mm table width: 5500 mm total power requirement: kW weight of the machine ca.: t dimensions of the machine ca.: m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

The scope of delivery includes: Steel panel, new Material colour: sendzimir galvanised Total width: approx. 295 mm Total depth: approx. 1,110 mm Inner depth: approx. 1,104 mm for column depth: approx. 1,100 mm Clear span: approx. 992 mm Truss support: approx. 55 mm Height of bending: approx. 25 mm Material thickness: approx. 2.00 mm Weight / piece: approx. 5.95 kg Other quantities on request. Quantity: - clear width trusses: 01 pcs. 02 pcs. 06 pcs - 1,800 mm 07 pcs - 2,100 mm 08 pcs - 2,400 mm 09 pcs - 2,700 mm 10 pcs. - 3,000 mm 11 pcs. - 3,300 mm 12 pcs - 3,600 mm 13 pcs - 3,900 mm 20 pcs. 50 pcs. 75 pcs. 100 pcs. Your contact persons in our company: Mr.: Andre Evering Sir: Mario Klöver Mr.: Falk German General information about the article: This item is only available for pickup. An additional desired transport or a shipment of this item is a ...

A used Wiesheu DUO in-store baking oven B4 + B8 EM Vario from 2015 is currently for sale and immediately available in stock. The oven consists of two ovens on top of each other, a B4 oven which is for 5 trays of 60x40cm and a B8 oven which is for 10 trays of 60x40cm each. The oven has two digital controls including baking program storage. In addition, the stove is mobile on castors and has a fixed water connection. Wiesheu DUO In-store Baking Oven B4 + B8 EM Vario - Stainless steel clad - Large glass front -digital control - 5 cushions 60x40 cm (upper oven) - 8 60 x40 cm cushions (lower oven) - Mobile on swivel castors - With steam condenser Dimensions: Height: 217 cm Width: 94cm Depth: 95cm + hood 25cm Specifications Year of Make: 2015 Voltage: 400 V / 50 Hz Power: 20.8 kW Rated current 32 A

capacity 90 degrees: round: 250 mm capacity 90 degrees: square: 210 mm : 290 x 210 mm saw band length: 2.965 x 27 x 0,9 mm mm table height: 940 mm band speed: 25 - 90 m/min total power requirement: 1,1/1,3 kW weight of the machine ca.: 0,35 t dimensions of the machine ca.: 1,3 x 0,8 x 1,5 m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Counting and banding machine ATS US 2000 FSB-DBN-T; State as is; should be installed by ATS Customer Service; suitable for processing banknotes; Rontech MF-360 RAV counting feeder; 1x Banderolier ATS US 2000 AD bandwidth 40mm and frame 260x260mm; 1x Banderolier ATS US 2000 AD Bandwidth 30mmund Frame 260x120mm; Turning unit installed. Count and banding machine ATS US 2000 FSB-DBN-T; condition as is; should be installed by the support of ATS; used for banknotes; count feeder Rontech MF-360 RAV; 1x banding machine ATS US 2000 AD with band width 40mm and frame 260x260mm; 1x banding machine ATS US 2000 AD with band width 30mm and frame 260x120mm; turning station.

capacity 90 degrees: round: 305 mm capacity 90 degrees: square: 260 mm : 350x200 saw band length: 3375x27x0,9 mm band speed: 18 - 100 m/min table height: 940 mm total power requirement: 1,5 kW weight of the machine ca.: 0,65 t dimensions of the machine ca.: 1,5 x 1,75 x 1,9 m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

cutting diameter: 220 mm saw band length: 2455 mm table height: 850 mm cutting width: 230 mm cutting speed: 25 - 80 m/min dimensions of saw-band: 2455 x 27 x 0,9 mm : 90 mm : 90 mm : 90 x 100 mm : 150 Impact energy: 150 Air consume per blow: 150 x 210 : 220 mm stroke back stop: 210 mm cross-slide: 230 x 185 total power requirement: 1,2 kW weight of the machine ca.: 0,24 t dimensions of the machine ca.: 1,2 x 0,6 x 1,7 m Miter cuts to 60 ° left - cutting speed 35/70 m / min. - Vice with rapid clamping device - Bandsaw blade guide made of hard metal - Band tension control - Electric cooling automatic. The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

capacity 90 degrees: round: 250 mm capacity 90 degrees: square: 210 mm : 290 x 210 mm saw band length: 2.965 x 27 x 0,9 mm mm table height: 940 mm band speed: 25 - 90 m/min total power requirement: 1,1 / 1,3 kW weight of the machine ca.: 0,35 t dimensions of the machine ca.: 1,3 x 0,8 x 1,5 m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

capacity 90 degrees: round: 250 mm capacity 90 degrees: square: 210 mm : 290 x 210 mm saw band length: 2.965 x 27 x 0,9 mm mm table height: 940 mm band speed: 35 + 70 m/min total power requirement: 1,1 / 1,3 kW weight of the machine ca.: 0,35 t dimensions of the machine ca.: 1,3 x 0,8 x 1,5 m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

capacity 90 degrees: round: 255 mm capacity 90 degrees: square: 240 mm : 300 x 180 saw band length: 2.765 x 27 x 0,9 mm mm table height: 950 mm band speed: 18 - 110 m/min total power requirement: 1,5 kW weight of the machine ca.: 0,42 t dimensions of the machine ca.: 1,23 x 1,7 x 1,75 m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

capacity 90 degrees: round: 305 mm capacity 90 degrees: square: 260 mm : 350x200 saw band length: 3375x27x0,9 mm band speed: 37 + 74 m/min table height: 940 mm total power requirement: 1,5/1,8 kW weight of the machine ca.: 0,65 t dimensions of the machine ca.: 1,5 x 1,75 x 1,9 m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

capacity 90 degrees: round: 130 mm capacity 90 degrees: square: 130 mm : 130 x 125 dimensions of saw-band: 1440 x 13 x 0,65 mm dimensions: 350 x 690 x 520 m band speed: 30 - 80 m/min total power requirement: 1,2 kW weight of the machine ca.: 19 kg The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

capacity 90 degrees: round: 510 mm capacity 90 degrees: square: 450 mm : 650x450 band speed: 15 - 100 m/min table height: 844 mm dimensions of saw-band: 5320 x 34 x 1,1 mm total power requirement: 3,0 kW weight of the machine ca.: 2,1 t dimensions of the machine ca.: 1,9 x 2,87 x 1,3 m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

automatic baler Manufacturer: HSM Type: VK 8818 R-FU, 100 t Year of manufacture / delivery date: 12/2012 Operating hours: approx. 13,500 specifications: Press force: 1000 kN Specific pressing pressure: approx. 120 N/cm² Channel format: 1,100 x 750 mm (W x H) Binding: 5-fold horizontal Wire push-through: seen in the direction of pressing on the left side Filling opening: 1,800 x 990 mm Drive power: 2 x 45 kW Control: S7-300 Theoretical throughput: - At 20 kg/m³ bulk density: approx. 12.86 t/h - At 50 kg/m³ bulk density: approx. 32.15 t/h Cycle time: approx. 8.3 sec. Bale dimensions: approx. 750 x 1,100 x length (600-1,200) mm Bale weights: approx. 500 - 750 kg Machine weight: up to approx. 30,000 kg including: - Remote maintenance system - Wire Slot Maze - Press box double-walled with replaceable HARDOX 500 sh ...

Star Ball Mill, Rotor Ball Mill, Centrifugal Ball Mill, Centrifugal Ball Mill Used. Manufacturer: EHINGER IMPIANTI Type: RM 150 Achievable grain sizes: with dynamic classifier: 0-20 μ and 0-300 μ with static selector 0-2 mm Average continuous output approx. 1.6 t of glass per hour Motor SIEMENS 75 kW 738 rpm 400 V Dimensions approx. 2850 x 4100 x 5000 mm original matching dust filter with fan The mill pictured serves only as a sample. The mill for sale is currently being revised. These mills are now being built by Eirich as an OrbitMill for the fine grinding of industrial minerals. Performance data of the Orbit Mill according to the manufacturer as an example of limestone. Air flow rate 13000 m³/h Limestone Throughput d97= 20 μm : 1.6 t/h d97= 40 μm : 3.3 t/h d97= 105 μm : 6.0 t/h The mill pictured was used in glass recycling. Four balls, which a ...

For sale is a used Markem Imaje large print printer 5800, which produces the printed image with wax. It is a conveyor belt and bracket for printer unit and controller. Print speeds of up to 178 meters per minute at approx. 200dpi resolution. Maximum print height per print head of 65 mm (print length flexible). Up to two print heads can be controlled; Print height up to max. 130 mm possible on one side, With Ethernet and USB interface / inputs and outputs freely programmable All-in-one printhead design for space-saving integration.Short heat-up phase max. 20 minutes. Colour touch display integrated in the controller. Printing costs according to Markem Imaje 1450ml = approx. 320 EUR, 400,000 layouts per year, 7267 ml necessary, annual costs of operating resources, estimated: 1,600 EUR Operating costs per tray, estimated: 0.004 EUR SAMPLE CALCULATION / SAMPLE LAYOUT

As good as new measuring frame with X-ray radiation for basis weight measurement on web fabrics up to a maximum width of 1000 mm. YOC 2014, approx. 2 ́100 operating hours, fully functional X-Ray-Gauge in good condition, for meassuring coatings or material weights up to max. 1000 mm widht. YOC 2014, about 2 ́100 running hours, fully functionable

Tier Oven Wachtel Piccolo I-6 DMS 3 Year of Make: 2016 A used electric deck oven Wachtel Piccolo I-6 with 6 shelves each 80x60cm is for sale. This oven is function-tested immediately available in stock. The oven is equipped with exhaust hood and proofer. Deck Oven Quail Piccolo I-6 DMS 3 Glass with 7-Day Clock - 6 shelves each 80x60cm - Each floor with separate controls - Top and bottom heat can be controlled separately - Each floor with a separate steam box for the generation of steam - With automatic night start function - With exhaust hood - Stove with water connection for steam - 29.3 kW - Voltage: 400V AC/3Ph/N/PE/50Hz - Year of construction: 7/2016 Shipping costs and trade-in on request.

Polystyrene compressor Styropactor MAXI | Shredder press for Polystyrene EPS Compressor, combination of shredder and press for polystyrene EPS MAXI Commodity number: 42055 Throughput: Measured with fish crates of 25 KG/M3 Material space weight EPS: 70-90 kg/h Throughput measured in fish crates with lid (650 grams per piece and about 800x400x220mm): 100-120 Connection: 7.5kW, 3-phase 400V/50Hz 480V/60Hz Insertion opening: 600×1000 mm Length: 3180 mm Height: 1600 mm Width: 870 mm MAXI PLUS Commodity number: 42060 Throughput: Measured with fish crates of 25 KG/M3 Material space weight EPS: 110-130 kg/h Throughput measured in fish crates with lid (650 grams per piece and about 800x400x220mm): 170-200 boxes/h Connection: 11kW, 3-phase 400V/50Hz, 480V/60Hz Insertion opening: 600×1000 mm Length: 3680 mm Height: 1600 mm Width: 870 mm Wet boxes: YES Stainless stee ...

Filling station, bagging station for big bag, octabine with material conveying blower Big Bag filling station with conveyor blower for filling regrind or granules in Big Bag 1.5 m³ The Big Bag filling station is robust and easy to handle. The system is ideal for use where dry granules or regrind are to be filled into octabine or big bag. Compact versions have been developed for smaller containers such as small boxes and sacks. These filling stations are ideal for smaller granulators or insert mills to fill smaller quantities of regrind into small boxes or bags. With a sophisticated design and a wide range of combinable options, the filling station can be filled for various bulk materials. The frame and the entire construction is made of sturdy profiled steel materials. Material handling system | Filling station, emptying station for one or two big bag or octabin or for small ...

: 36/72 m/min : 285 mm capacity 90 degrees: round: 250 mm capacity 90 degrees: square: 230 mm capacity 90 degrees: flat: 280x200 mm capacity 45 degrees: round: 190 mm capacity 45 degrees: square: 180 mm capacity 45 degrees: flat: 180x180 mm capacity 60 degrees: round: 120 mm capacity 60 degrees: square: 110 mm capacity 60 degrees: flat: 110x110 mm dimensions of saw-band: 2950 x 27 x 0,9 mm output: 1,5 / 1,8 kW Weight: 435 kg dimensions: 1700x1000x1840 mm Semi-automatic function: - Vice closes and engine starts - Saw head lowers for the cut - Engine shuts off - Saw head lifts - vise opens The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Vibronics Ultrasonic Bath Brand: Vibronics Power 1.8 kw; Serial number: 6092 Total dimensions L: 2800 mm; W: 1700 mm; H: 930 mm; Tank size: WxHxD= 1350x720x990 mm Frequency 25 kHz equipped with 4x generators

material dimensions max. round: ​Ø 380 mm max. square: 380 x 380 mm segment length with single stroke: 10 - 510 mm with multi stroke: max. 4590 mm dimensions LxWxH: 3100 x 2200 x 1850 mm weight: 3.100 kg

Deck Oven Miwe Condo CO 5.0806-4E Year: 2017 Stone Slabs Oven Miwe Condo CO 5.1206-4E Electric - 5 shelves each 80x60cm - lower 4 floors have an entrance height of 13cm - top floor has an entrance height of 17cm - Each floor can be controlled separately - Top and bottom heat can be controlled separately - Each floor with separate steam function - with proofer - With steam condenser - With exhaust hood - Floor entrance height 13cm - Total connected load : 29,9kW - one double chamber 11kw each - Top floor 5.7 kw - Proofer: 2.2kW - Year of construction 2017 Dimensions: Width: 110cm Depth without hood: 115cm, with hood +40cm Height: 216cm

Plant number 701-246; medium used radionuclide Krypton 85 Type: X1114 Specifications: Connection voltage: 40V +/- 10%, 3 phases, 50 Hz, N, PE Basis weight measurement: measuring range 30-600 μm PA; Measurement accuracy +/- 2; Sigma range (+/-0.4% but maximum +/- 0.4 μm), Measuring gap 10 mm Traverse: maximum useful width 1970 mm, traverse speed 0-10 m/min Ambient temperature: sensors 0-50°C, traverse 0-50°C, control cabinet (control) 10-35°C Humidity max. 90% without condensation

Precision ball screw drive, KGT 50mm, Gewindelg 2670mm, Rexroth, new Special price If you have a VAT number, we will gladly issue you an invoice without VAT. Mint condition in original packaging! The part was purchased from a spare parts warehouse of a company and has never been in operation, is in a completely mint condition and in its original packaging. - Precision ball screw /ball screw with nut - Thread nominal diameter 50mm, pitch 10mm, 4 turns, that means 40mm travel per turn of the nut, - Total length: 2930mm, - ball screw length: 2670mm Shaft end 1: 165mm lg - D32 x 35mm lg, thread M35 x 1,5 x 25mm lg, D35 x 85mm lg, D42 x 20mm lg Shaft end 2: 95mm lg - thread M25 x 1,5 x 28mm lg, D35 x 53mm lg, D42 x 14mm lg Function guarantee! For second hand parts, we can not provide a conventional warranty and guarantee. However, we give you a functional guarante ...

USED PRECISION GEARS LTD TR-100 BLISTER BACKAGING MACHINE REF.: E0034 PRECISION GEARS LTD blistering machine to blister tablets, capsules, dragees, etc. For PVC / Aluminum blister Model TR-100 Year 2000 Batch marker for incision, pre-cut, cut, Production of 50/60 strokes per minute, depending on the selected blister size, up to 240 blisters per minute. Maximum format size 190x130 mm. Current format blister of 10 capsules of 170x 100 mm General characteristics: Manufactured by PRECISION GEARS LTD Model TR-100 Year built 2000

Miwe aero in-store oven Type: AERO AE 6.0604 Specifications: digital Miwe FP 12 control for 6 sheets 60×40 cm with fermentation cabinet for 16 sheets 60×40 cm with vapour destroyer Year of construction 2006 Specifications: 400V / 230V / 3/N/PE / 50Hz Electric Dimensions: Height: approx. 194 cm Width: approx. 90 cm Depth: approx. 100 cm

Baguette Long Scooter Kemper FR Kombi - Baguette long scooter from Kemper - Model FR COMBI - Stainless steel clad - with outlet table - can be driven on castors - 400 Volt 50Hz

Major Baguette Long Scooter with feed belt / conveyor belt relatively good condition without export plate 380V 50Ht on rolls Metrics: Height: 160cm Width: 100cm Depth: 150cm