marcantonini srl used for sale

The IRS 120 Easy is the perfect entry point into cable recycling. The special combination of large flywheels and multi-part segment cutting knives makes it possible to efficiently recycle old cables made of copper or aluminium even without high power consumption and without shredding. The machine impresses with its small footprint, is easy to maintain and easy to use. Compared to most of the competition's systems, the machine has two separate fans for separator air and dust removal. This eliminates the usual interactions between more or less clogged filters and the purity of the copper granules. In addition, the separator air is not roughly adjusted via throttle valves, but by sensitive adjustment of the fan speed. This gives you the best qualities in finished copper. This machine is an immediately available storage machine and has 4 screen inserts, electronic pre-equipment for ...

Small shredder for various tasks such as old cables, plastics wood, etc. With hydraulic, electronically controlled feed. Drive 18.5 + 2.2 kW (rotor + feed). Rotor shaft with connectors for connecting a cooling device (e.g. when used for NYM old cables. The machine is 1 year old and little used from our demo machine inventory. The machine is offered with a one-year used machine warranty.

Small shredder for a wide range of tasks such as old cables, plastics wood, etc. With hydraulic, electronically controlled feed. Drive 18.5 + 2.2 kW (rotor + feed). The machine was overhauled by the manufacturer ISVE in September 2020 and supplemented with an electronics for networking into a cable recycling line. A rotor cover for the optimized processing of old cables has also been added. Currently, the shredder has a 16 mm hole sieve but other hole diameters can also be added. With the 16 mm hole sieve, the shredder reaches about 250 kg/hour when processing mixing cables.

The mixer combines hot and cold mixing. After hot mixing, the material automatically enters the cold mixer for mechanical cooling. -hot tank 800 l. - cooling tank 2000 l. - hot stirring time from 6 to 10 min. - cooling time from 10 to 15 min. - engine power 110 kW The device is adapted to the production of WPC terrace boards. Components needed for the product, such as PVC and wood dust or MDF dust, can be combined.

Mixer for plastics CONBOPLAS SRL8002000754 The mixer combines hot and cold mixing. After hot mixing, the material automatically enters the cold mixer for mechanical cooling. - hot tank 800 l. - cooling tank 2000 l. - hot mixing time from 6 to 10 min. - cooling time from 10 to 15 minutes. - engine power 110 kW The device is adapted to the production of WPC terrace boards. Components needed for the product such as PVC and wood dust or MDF dust can be combined.

Small but very robust and powerful shredder for a wide range of tasks such as old cables, plastics, wood, etc. With hydraulic, electronically controlled feed. Drive 18.5 + 2.2 kW (rotor + feed). Rotor shaft with connections for connecting a cooling unit (e.g. when used for old NYM cables. The machine is and little used from our demo machine inventory. The machine is offered with a one-year used machine warranty.

STRIP WIDTH: MAX. 160 MM; THICKNESS RANGE: 0.5 - 3.0 MM, TUBE OD.: 12 - 50.8 MM, TUBE LENGTH: 3-6 M, TIG-TRICATHODE + LASER ROFIN SINAR 6 KW

THIS LINE IS USING FOR ALUMINIUM PROFILES IN PRODUCTION OF WINDOWS, DOORS CURTAIN WALLS ETC. POWER: 60 KW, PLC MITSUBISHI, MAX. WORKING WIDTH: 6.5 M, ALU THICKNESS: 0.2-0.25 MM, STRIP WIDTH: 120 - 230 MM, COIL WEIGHT: 360 KG

Qty. 1 Second-hand automatic sheets (pallets) storage system Mfc.: MATTER S.R.L Built: 2002 Model: Mat 00.6 Number of Automatic Retrieval Cars: 2 Number of drawers: 756 Pallets Dimension of Pallets: Width: 1000/1500 mm / Length: 2000/4000 mm / Height: 250 mm Max. Pallet Weight: Max: 3000 kg Maximum speed of Retrieval Cars: Y Axis: 11 m/min . / X Axis: 58 m/min. / Z Axis: 20 m/min. System is working with Picking Station for separating and handling of pallets Dimensions of the system: Length: 74 meters x Width: 9.40 Meters (not including the picking station) X Height: 9.6 meters ( 9 rows )

Food Pack machinery / flow pack machine. The machine is designed for wrapping various products for food industry products or other non-food products in film. Manufacturer: Food Pack Machinery SRL Italy Type: Leonardo 700 Year of production: 2010 Control from the color touch screen panel Max film width 700 mm Dimensions: Length 6160 mm, Width 1390 mm, Height 1860 mm Weight: 600 kg Electricity: 380 v., 50 Hz, 6.4 kW Without need: 6 bar Packaging film: Polyethylene The width of the machine's packaging tunnel can be changed according to the width of the wrapper (film) with a handwheel and a digital display. The height adjustment works the same way. The machine is in good condition and clean.

Manufacturer: various YOM: 1986, overhauled in 2018 Capacity: 500 kg / h The system consisting of: cutter by ZIMMER. Stretcher by Muzzarelli MC Dena Srl. Sausage forming machine Muzzarelli MC Dena Srl., ES3000 mozzarella forming machine for balls by Milky lab 4 x form rollers for mozzarella balls Packaging machine for mozzarella balls PFM., PV260 Condition: used, excellent operating condition

Stock# U2397-1 Used stainless steel twin shaft paddle mixer by V.V.S. DI VISCONTI SRL (Italy) model I1500SF with total volume of mixing chamber 2500 l. Working volume in range from 1500 l up to 1700 l. Weight of batch up to 1500 kg. Machine has internal dimensions of mixing chamber W 1100 mm x L 2870 mm x D 900 mm. Shafts are driven by el. motor 22 kW, 1470 rpm, 400-600 V, 50 Hz, via reducer and belts. Working rotation of each shaft is 33,5 rpm. Mixer has top open. Discharge through one outlet with dimensions 500 mm x 200 mm, in front wall. Outlet is equipped with pneumatically operated lid layered with teflon. Mixer has stainless steel lifting device for work on rectangular containers with volume 200 l and width 660 mm. Lifting device is operated electrically. Machine has technical documentation. Last time used in food industry.

4 ROLL HYDRAULIC MODEL M2008 EVO_4.0 CNC GRAPHIC CAD-CAM Machine serial number 2022 PLATE BENDING ROLL PLANETARY DESIGN DOUBLE PINCH PRE-BENDING Capacity -Width of plate: 2000 mm -Thickness of plate rolling 8 mm -Thickness of plate pre-bending 6 mm -top roll 190 mm -lower roll 170 mm minimum rolling shell ID 220 mm -Power 5,5 Hp to run the hydraulic unit Voltage 400/50 – 480/60 -Weight of the machine 3400 Kg Configuration installed Surface hardening of the four rolls, smooth finishing suitable for stainless plates rolling Dual pre-pinch, with adjustable force upon the input of plate thickness Conical bending hydraulic attachment - hardened contrast pad. Power driven rolls rotation top/bottom gearbox axial direct drive hydraulic each roll. Calibration system f re-rolling of welded shells rounding. Console electric in ...

SLEEVE APPLICATOR CLEVER GS 602. performance on PET/Glass bottles: 45000 b/h : 0,4-0,5 L 24000 b/h : 1,5 L 22000 b/h : 2 L

CUP LABELING / LABELER BLINK RM 50 (FOUR OR TWO CUP / SIDE AND GROUND) M. No.: 950136 Voltage: 380 V // 50 Hz // 6A

machine measurements: 3200x1700x2100 mm machine weight: -- kg power capacity: -- kW Condition: used Specification: Ultrasonic cleaning system type: Fisa 3VSD 150D - ultrasonic cleaning system consisting of: (see description) 1. tub 1 - cleaning agent 2. tub 2 - tap water 3. tub 3 - preservative 4. cleaning area 5. control - Cleaning cycle in tub 1 approx. 10-20 minutes - Operating temperature between 70-75°C - Extraction ON during cleaning process (Extraction fans are not are not included in the scope of delivery. - Cleaning with water in tub 2 - Cycle time in tub 2 approx. 10-20 minutes - Preservation in tub 3 - Preservation cycle time in tub 3 approx. 10 minutes - Blowing off the parts in the cleaning area under suction - incl. two cleaning baskets - The motors for the suction system in tub 1 and in the cleaning area are not included in the scope of delivery.  ...

100 W laser and filter for fume extraction, both the laser and the filter worked only for a few hours, purchased new in March 2023, the laser worktop is 110 × 70 CM, complete with PC and bench.

Sartore SRL turning device for pipes up to 9000m and 300t Roller block with stepless speed adjustment and manual spindle adjustment technical Total load capacity 300 tone Workpiece diameter 1000 - 9000 mm Turning speed 60 - 1200 mm / min

Unipac Silver 80 automatic plastic tube filling machine. The machine is well suited for packaging pharmaceutical, chemical, cosmetic, food, etc. products. Manufacturer: Unipac srl Italy Type: Silver 80 Year of production: 1988 Automatic cassette-type feeder for tubes Material: Stainless steel Funnel with stirrer Tube sealing (hot jaw) Various exchange format sizes Electricity: 380 years, 50 Hz Weather: 6 bar The machine is in good working order

The system is composed of a Hyundai HA006L anthropomorphic robot managed by a multiprocessor RISC three-station three-corner positioner, from multifunction inverter generator for welding, anti-collision sensor, torch cleaning group and protections. Year 2020.

Vacuum-vacuum autoclave for wood treatment up to risk III

Semi-new automatic cellophane wrapping machine with double sealing mass and 6 station feeder. Can be used for non-shrink cellophane wrapping.

Reepack Reeflex 150 Ecoline tray sealer Manufacturer: Reepack srl, Italy Type: ReeFlex 150 Ecoline Year: 2011 Stainless steel Mold: baguette format, 300 mm x 85 mm, 3 times Speed: 6 – 15 / min. Power: 400 v., 50/60Hz, 3-phase Weight: 1000 kg Dimensions: L 4060 mm x W 1300 mm x H 1820 mm

Capacity plate width up to 3000 mm thickness 22 mm plate prebend 18 mm dual prepinch technical data: -length of rolls 3100 mm -top roll dia. 350mm -lower roll dia. 330mm -Hydraulic power unit with 20Hp motor -Electric supply Vac 400/50 – 480/60 Configuration complete: -Hardened surface of the 4 rolls -Conical plate bend hydraulic attachment. -hydraulic power driven rolls rotation with gear unit axial each -Synchronized hydraulic power dragging . -front open drop-end to remove closed shells. -Calibration re-rolling feature for welded shells Safety configuration in compliance. Control console electric commands with digital readout Predisposed ready to connect nr. 1 central hydraulic support for large dia. nr. 1 side arm hydraulic to hold in place think plate sheet being formed

Max. circling length: 3100 mm Max. metal sheet thickness: without pre-bend - 6 mm Upper cylinder diameter: 200 mm Side cylinder diameter:: 190 mm engine tilt:: 4 kW Engine hours worked: : about 60-80

A fully equipped line for the production of polypropylene yarn type Technorope 1000/100/PP-300: Manufacturer: Sima Srl Useful width of the cutting head: 1000 mm Capacity: up to 300 kg/h, depending on the type of yarn Twister: 16 (with 16 batteries) Yarn types: from 5000 to 120 000 denies

Profile bending machine hydraulic heavy duty -output shafts 360 mm Equipped with traction tooling for H-beam HEB IPE INP rolling on the hard-side Configuration -pyramid dual pinch side rolls independent hydraulic -3 rolls driven hydraulic and gear unit -synchro. -set of rolls for HEB beam – INP beam - flat bar square bar. -Set of heads for traction the HEB – INP beam bending on the hard side -Set of rolls for pipe bending. Pipe 20 inches max capacity. -Lateral correctors left/right side hydraulic operated in 3 directions -Add-on rollers angle bending & T-section leg-in / leg-out -Control panel console electric joysticks manual use & program automatic -Digital readout screen display 8 axis position reading of the rolls - 8 axis automatic programmable bending works -Electric Vac 400/50 ( rewirable on request ) -weight total of the machine approx. 65 Ton ...

Features: chain conveyor is monitored, fill level is monitored via pressure difference in both chambers, large maintenance hatch on the discharge side, honeycomb filter below the flue flange, higher gear ratio with more powerful motor on the chain conveyor, water overflow optimised, larger water slider for emptying, the fan has ATEX certification.

Wood shredders, plastic shredders, garbage shredders, two-shaft shredders, shredders, shredders used Manufacturer: I.S.V.E. Srl Type: 80-80 D Year of construction: 2003 Insertion approx. 1500 x 900 mm Insertion height approx. 1600 mm Drive 2x 9 kW 380 V Dimensions: approx. 2400 x 1800 x 2400 mm Changes and errors in the technical data, information and prices as well as prior sale reserved.

There are three identical machines available, connected load: 8.5kW.

Siate srl waste water control system, type: PL 750/1700, number: CO98843, 380/400 V, 50 Hz, 25 A, dimensions: 2500 mm x 950 mm x 1800 mm.

Description Heating platen Ce certificate

Plate bending roll Capacity 3000x75 mm MG model 4ROLL Hydraulic machine with double pre-pinch -plate width up to 3000 mm -plate rolling thickness 75 mm Prebend 55 mm Tightest bending dia ID 800 mm Rolls length 3100 mm Upper roll 680 mm Lower roll 620 mm hydraulic unit power 100 Hp Hardened surface of the 4 rolls Pre-pinching with adjustable load to perform best roundness on edges Driven rolls powered with gear units axial and hydro motors each Cone plates bending, hydraulic conical plate rolling Electric commands joysticks and position readout with 4 axis cnc Drop-end hydraulic front open to unload closed shells. Digital readout of the 4 bending rolls. Variable speed rolling control. Central support can be added to support large dia. Shell forming Side arm can be added to hold in place think plate sheet being formed Weight of the machine ...

Bending capacity: Plate width: 3000 mm Plate thickness 140 mm Thickness max 200 mm depending on plate width and yield strength Technical data: 3100 mm Surface useful length on rolls 940 mm size of Top roll 840 mm size of Lower rolls 210 mm max thickness opening between the rolls 400/50 Vac voltage - rewirable 480/60 220 Hp Power electric installed Configuration installed with the machine Hardened surface of the 3 rolls. Conical plate bending hydraulic attachment with hardened contrast pad. All the 3 rolls driven with axial gearbox and motor each roll independent Calibration system for the re-rolling of welded shells rounding unwanted flat spots. Console electric on wheels with centralized commands joysticks and digital readout. Opening front side hydraulic drop-end to unload closed shells. Variable speed working slow/fast. Emergency systems  ...

Profile bending roll used equipment hydraulic model AR200 year 2008 make MG Italy Capacity bending chart photo in enclosed -Technical data: Output shafts size 200 mm -Machine complete with set of rollers adjustable for the various shape of profiles. -Traction tool hydraulic operated for the HEB-beam - IPE - UNP bending the hard side. -Lateral correctors left and right side hydraulic operated in 3 direction. -Included additional set of rolls for pipe 6" inches -Machine with 3 rolls driven system with individual hydraulic motor and axial gear-unit on each shaft. -The 3 shafts working on bearings, heavy duty type with sealed lubrication. -Centralized control panel movable on wheels with all electric commands. -Dual rolling speed up to 5 mtr/min with automatic balancing system between the 3 rolls. -Safety devices in compliance with European regulation. CE mark. - ...

FREEZER CABINET, YORK SAMIFI FREEZERS SRL, MODEL: MIDI C/15 Technical features: Refrigerant: NH3/R717 Plates number: 16 plates Stations number: 15 stations Station size: 1835 x 1140 x 100 mm Dimensions: 2700 x 1620 x 2700 mm

3-roll hydraulic 3000x30 mm pre-pinch planetary MG model G3030 year 2021 -Plate width 3000 mm -Capacity thickness 30 mm -Pre-pinch 25 mm -width on the rolls 3100 mm -upper roll size 400 mm -lower rolls size 380 mm -Hardened rolls surface. -All driven 3rolls gear box motorized each synchronized rotation -Conical plate bending attachment , rolls tilting & contrast roller. -Operator console with directional joysticks and digital readouts -Front drop-end open hydraulic -Emergency and safety installation -User manuals and instruction books. -Electric power 25 HP on the hydraulic unit. -V400/50

Pellet heating, pellet stove, biomass stove used. Manufacturer: ELMEC Group Srl Type: B-MAX 300 EBBR020300-P01 Year of construction: 2018 Burner power max. 300 kW Nominal power 250.2 kW Max water temp. 90°C Boiler dimensions: approx. 1700 x 1100 x 1650 mm Additional burner approx. 1000 x 500 x 900 mm Pellet hopper approx. 800 x 800 x 1200 mm + auger Subject to changes and errors in the technical data, specifications and prices as well as prior sale.

For sale is a used plate screen changer from the manufacturer BD Plast SRL. The screen changer is in a used but well maintained condition. Specifications: - Screen diameter: 250mm - Filter area: 491 cm² - Sealing ring PTFE/ Teflon - Heating capacity approx. 22kW - Number of control zones: 4 - Operating pressure max. 400 to 500 bar - Hydraulic unit designed for quick change - Throughput capability from 800 to 2,000 kg/h - Weight approx. 950 kg incl. documentation, documents, drawings, etc... Screen change can be visited by prior appointment.

Manufacturer : Aximatic srl Model: Optima 900 Matic Year : 1998 Type : Plastic tube filler Max capacity : 70 units / min Dosing range : 2 ml - 300 ml Max tube length : 280 mm with cap Tube diameter: 10 mm - 60 mm Power : 7 KW Current: 18 A

Control unit, control panel, control panel, control unit, keyboard, screen, controller, hand terminal, control unit -Manufacturer: Bierrebi LEA SRL. Control module from automatic cutting machine Bierrebi TA 103 -Circuit board: LEA SRL. Type LEA 1016 2.028.01.061.02 -Dimensions: 360/130/H60 mm -Weight: 0.4 kg

Control unit, control panel, control panel, control unit, keyboard, screen, controller, hand terminal, control unit -Manufacturer: Bierrebi LEA SRL. Control module from automatic cutting machine Bierrebi TA 103 -Circuit board: LEA SRL. Type LEA 1011 2.028.01.067.01 -Dimensions: 360/130/H60 mm -Weight: 1,3 kg

Control unit, control panel, control panel, control unit, keyboard, screen, controller, hand terminal, control unit -Manufacturer: Bierrebi LEA SRL. Control module from automatic cutting machine Bierrebi TA 103 -Circuit board: LEA SRL. Type LEA 1000 LEA 1002 2.028.01.057.02 -Dimensions: 265/125/H100 mm -Weight: 2.0 kg

Control unit, control panel, control panel, control unit, keyboard, screen, controller, hand terminal, control unit -Manufacturer: Bierrebi LEA SRL. Control module from automatic cutting machine Bierrebi TA 103 -Circuit board: LEA SRL. Type LEA 1000 LEA 1002 -Dimensions: 265/125/H100 mm -Weight: 2.0 kg

Control unit, control panel, control panel, control unit, keyboard, screen, controller, hand terminal, control unit -Manufacturer: Bierrebi LEA SRL. Control module from automatic cutting machine Bierrebi TA 103 -Circuit board: LEA SRL. Type LEA 1011 2.028.01.067.01 -Dimensions: 330/125/H50 mm -Weight: 0.9 kg

Control unit, control panel, control panel, control unit, keyboard, screen, controller, hand terminal, control unit -Manufacturer: Bierrebi LEA SRL. Control module from automatic cutting machine Bierrebi TA 103 -Circuit board: LEA SRL. Type LEA 1004 2.028.01.063.02 -Dimensions: 400/100/H50 mm -Weight: 0.4 kg

Control unit, control panel, control panel, control unit, keyboard, screen, controller, hand terminal, control unit -Manufacturer: Bierrebi LEA SRL. Control module from automatic cutting machine Bierrebi TA 103 -Circuit board: LEA SRL. Type LEA 1032 2.028.01.065.01 -Dimensions: 370/90/H28 mm -Weight: 0.4 kg

Control unit, control panel, control panel, control unit, keyboard, screen, controller, hand terminal, control unit -Manufacturer: Bierrebi LEA SRL. Control module from automatic cutting machine Bierrebi TA 103 -Circuit board: LEA SRL. Type LEA 1020 -Dimensions: 300/280/H80 mm -Weight: 3 kg

Control unit, control panel, control panel, control unit, keyboard, screen, controller, hand terminal, control unit -Manufacturer: Bierrebi LEA SRL. Control module from automatic cutting machine Bierrebi TA 103 -Circuit board: LEA SRL. Type LEA 1020 -Dimensions: 380/300/H130 mm -Weight: 4.3 kg

- Distance between columns: 2800 mm - Longitudinal travel – X axis: 6000 mm - Cross travel – Y axis: 3000 mm - Vertical travel – Z axis: 1500 mm - Spindle taper: ISO-50 (DIN69871) - Power of main motor: 37 / 45 kW - Spindle speed: 3000 rpm - Working feed: 0-10000 mm/min - Rapid feed X/Y/Z: 15000 mm/min - Centralized hydraulic and lubrication unit - Electrical devices: 380V, 3 phases, 50 Hz - AC servomotors (brushless) - Control of the machine Fanuc CNC - External/Internal tool cooling unit - Heidenhain linear scales for axes - Chain type chip conveyor - Levelling devices for foundation, 1 set. OPTION (not included in the price of standard machine) - TU-37 universal automatic milling head (37 kW, 3000 rpm, 1500 Nm, ISO-50, internal-external tool cooling, 2.5° indexing in 2 planes). - Automatic Tool Changer with 40 posts for milling tools. - Floor p ...