We use cookies to optimize our website for you and to be able to continuously improve it. By continuing to browse the site you are agreeing to our use of cookies.
Disagree
Manufacturer:
(Category: 307)
used
Lab Mixer Tangential Chamber volume 2,8 l / 2 l netto Sliding door AC motor 22 kW Year 1971
used
cross-section width:: 800 mmcross-section heigth:: 15 mmfeed:: ab ca. 5 mmspeed of feed:: m/mincuts max.:: Schnitte/mcondition: used, overhauledSpecification: Panel cutting machine - overhauled with CE- Section width max.approx.: 800 mm- Section height max.: 15 mm, depending on the hardness of the rubber sheets- Cutting length from approx.: 5 mm (depending on material)- cutting force approx.: 10 tons - Connected load approx.: 1.8 kW- Painting: green- Operating voltage: 3 x 400V, 50Hz, N, PE- Dimensions approx.: 1,200 x 1,450 x 1,950 mm - Safety devices according to current standards,- New on-board system machine,- New control cabinet with PLC system Siemens S7-1200,- CE marking,- Instructions for use and maintenance in English or German language ...
used
Tangential nett volume 70 l drop door AC motor 320 kW / 380 V / 50 Hz, 1483 RPM Year 1987
used
machine measurements: -- mmmachine weight: -- kgpower capacity: -- kWCondition: used, Specification: drum-type blast deburring machine type: MEWO Rotor TS 60- batch volume approx.: 1-600 litres,- working temperature: - 150°C- drum speed: 5 - 30 rpm- Blast wheel speed: 1,000 - 9,500 rpm- Control: Siemens S7 SimaticThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
used
manual roll gap adjustment 2x7.5 kW motor Bearing Oil circulation lubrication adjustable roller speed 10-41 rpm BJ 1990
used
clamping force: 1100 kNinjection volume: 1000 cm³screw diameter: -- mmplaten size: 330 x 500 mmCondition: used,Specification: frame injection moulding machine - usedclamping unit:- clamping force: 1100 kN- heating platen size: 330 x 500 mm- mould size: 500 x 400 mm- Clear width upper- lower platen: 740 mm- Clamping direction: from belowInjection unit:- Injection volume max.: 1000 cm³- Injection: from above- Voltage: 3x 400 V, 50 Hz, N, PE- Control voltage: 24 VDC- Hydraulics Rexroth: 7,5 kW- Control: ECO II / System X20- Pump capacity: 63 l/minUnits are currently still in production and will be available from August.There are 11 identical units, built between 2008 and 2010, available.The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
used
Small blasting machine for cryogenic deburring - MEWO 42
used
roll diameter: 550 mmroll length: 1500 mmrolls drilled: Kernbohrung Nip adjustment: hydraulisch 0total power requirement: 90 kWThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
used
Complete production plant retreading plant for cold-retreaded truck tyres Output: 30,000 pieces/year Equipment: Rail System "Helm 500" Frame/Supports Manufacturer TRM Monorail system "Helm 500" frames/supports manufacturer TRM Rail length approx. 110m, rail height approx. 2m Monorail length approx. 110m, rail height approx. 2m 76 hooks with rollers 76 hooks with rollers various turnouts Various switches 3 processing stations incl. extraction connections 3 repair stations including extraction connections Spray tunnel for rubber solution incl. extraction cementing tunnel for rubber solution incl. suction Roughener Matteuzzi RAS 90 DC 4 Matteuzzi RAS 90 DC 4 buffing machine Roughening machine Bandag Bandag buffing machine Autoclave station for two 24 mm autoclaves with 139 hooks (long+short) Model TRM Autoclave station for two 24 autoclaves with 139 hooks (long+short) ...
new
machine measurements: 850 x 1.800 x 1.450 mmmachine weight: 360 kgpower capacity: 0,7 kWCondition: newSpecification: Powder coating machine, type: EPC-30/2EThe machine is designed for the powder coating of cables, hosesand profiles.- Product diameter max.: 30 mm- Product speed max.: 1,500 m/min- Powder throughput min.: 30 g/min with fine dosage- Powder throughput max.: 400 g/min per powder injector- Electrostatic: available as option- Connected load: 0.7 kW- Dimensions LxHxW: 850 x 1,800 x 1,450 mm- Weight approx.: 360 kgThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
used
ROLL DIAMETER 550 mm POLL WORKING LENGTH 1530 mm MOTOR POWER 110 KW DIMENSIONS: 630022301830 (L×W×H) SPEED RATIO OF ROLLS 1:1.27 Structure description 1 Base frame is welded and annealed . 2 The motor is 3- phase asynchronous motor, protection levels :IP54. 3 The driving type :Single out- shaft or double out- shaft. The speed reducer is hard gear reducer,which has long service life and low noise. 4 The roller bearing is rolling bearing with Low noise, save power almost 20%. the roller bearing use grease lubricating. 5 The nip adjusting Motor type 6 This machine is equipped with two pieces of moving blade. 7 Safety device : Pull the safety rod to achieve emergency stop. It can be installed with kick stop device and emergency stop device for safety. 8 The electrical design theory conform to the TWO ROLL MILL specifications strictly . It is equipp ...
used
roll diameter: 150 mmroll length: 300 mmrolls drilled: Flaschenhals Nip adjustment: hydraulisch total power requirement: 4 kWcondition: used, overhauledSpecification: Laboratory Rolling Mill 150 x 300 mm - second-hand Motor under the rollers- Roller diameter approx.: 150 mm- roller length: 300 mm- Friction between the rollers- Rolls drilled with central chamber for water cooling- Rolls with new slewing rings, manufacturer MAIER, for water cooling,- Rollers mounted on bronze bushes with circulating oil lubrication via pump,- Gap adjustment: NEW, hydraulic and as emergency system- Hydraulic unit NEW- NUE Tilting guide plates- NEW safety cage- Safety brake for emergency stop- AC brake motor: 4 kW - 400 Volt - 50 Hz- new mixing tanks made of stainless steel for the mixture- Safety devices according to current EN 1417:3/2015- Painting: in RAL colours according to ...
used
5501500 TWIN SCREW 1. 1 PC 5501500 OPEN MILL RUBBER MIXER 2. 1 PC 5501500 OPEN MILL RUBBER MIXER 3. ELECTRIC CONTROL CABINET WITH DRIVER 4. DIRECT CONNECTION (COUPLED) 5. BRONZE BEARINGS 6. AUTOMATIC LUBRICATION 7. 160 KW 990r/min
new
cross-section width:: 100 mmcross-section heigth:: 40 mmfeed:: 2 - 999.999,9 mmCondition: new,Specification: Impact knife cutting machine CC-600/40 for hoses and profiles- contact length: 600 mm- product diameter: 40 mm- belt width: 100 mm- Tractive force: 400 N to 800 N- Drive: 2 drives upper and lower belt- Conveyor belt speed: 100 m/min- Drive feed, cutting motor: Servo drives- Cutting capacity with blade max.: 4,000 1/min- Connected load: 3.5 kW- Dimensions L/H/B: 1,900 x 1,650 x 960 mm- Weight approx.: 580 kgThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
used
L/D=20.7 External dimensions 2700×1000×1400(LxWxH) Screw stiffness HRC65-68 Screw diameter 90mm Engine power 30KW/1470rpm SCREW LENGTH 1860 mm Heating section number/power 6kw×2
used
cross-section width:: 100 mmcross-section heigth:: 50 mmfeed:: 10 - 999.999,9 mmspeed of feed:: 1 - 50 m/minThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
used
ROLL DIAMETER 400mm POLL WORKING LENGTH 1000mm MOTOR POWER 45 KW DIMENSIONS: 447118501760 (L×W×H) SPEED RATIO OF ROLLS 1:1,27 Structure description 1 Base frame is welded and annealed . 2 The motor is 3- phase asynchronous motor, protection levels :IP54. 3 The driving type :Single out- shaft or double out- shaft. The speed reducer is hard gear reducer,which has long service life and low noise. 4 The roller bearing is rolling bearing with Low noise, save power almost 20%. the roller bearing use grease lubricating. 5 The nip adjusting Motor type 6 This machine is equipped with two pieces of moving blade. 7 Safety device : Pull the safety rod to achieve emergency stop. It can be installed with kick stop device and emergency stop device for safety. 8 The electrical design theory conform to the TWO ROLL MILL specifications strictly . It is equipped ...
used
cross-section width:: 700 mmcross-section heigth:: 500 mmfeed:: -- mmCondition: used, overhauledSpecification: splitter for rubber bales - overhauled with CE- cross section width max.ca.: 700 mm- cross section height max. approx.: 500 mm- cutting force approx.: 10 tons - AC motor: 4 kW, 400 V, 50 Hz- Infeed roller conveyor for product transport- Machine stands on a raised pedestal- Two-hand safety control for driving the blade movement- Safety guard according to current standards- New control cabinet- New on-board system machine- Operating and maintenance manual in English- CE marking- Paintwork: according to customer requirements- Refurbished with 1 year warranty- CE marking,Option:- Output roller conveyor newThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
used
Iddon 75mm Cold Feed Rubber Extruder With roller feed With motor, gearbox and control panel
used
roll diameter: 550 mmroll length: 1500 mmrolls drilled: Kernbohrung Nip adjustment: Hydraulisch total power requirement: 150 kWCondition used, refurbished, Specification Roll mill 550 x 1500 mm - used- roll diameter: 550 mm- roll length: 1500 mm- Variable friction ratio between rolls - cored rolls with central chamber for water cooling- nip adjustment: NEW hydraulical- hydraulic unit: NEW- tipper guiding plates- cylinders: mounted on bronze bushings with forced oil lubrication by pump, new rotary joints for connections to water circuit- N.2 safety brake for emergency stop - N.2 AC engine 75 kW – 380 V – 50 Hz- mill tray to contain compound- bi-directional bars for safety system- visualization display to monitor gap between rolls an ...
used
Yizumi Injection Press Model: YL2-V280L Clamping force 2800 kN Volume: 2000cc Mold open stroke 500mm Min. mold height 100mm Heated platen size 670mm x 780mm Heating plate daylight 600mm Injection pressure 1970 bar Theoretical Injection volume 2000cm3 Oil pump power 11kW System pressure 230 bar Total power 37kW Power supply: 415V, 50Hz, 3P+N+PE Rexroth variable pump + Inovance servo motor: Year 2021 CE marked
used
clamping force: 1.300 kNinjection volume: 230 cm³screw diameter: 45 mmplaten size: 685 x 685 mmCondition: used,Specification: injection moulding machine for TPE - usedincluding Koch dosing unitclamping unit:- clamping force: 1.300 kN- heating platen size: 685 x 685 mm- Clear distance between tie bars: 470 x 470 mm- Mould installation height min.: 250 mm- Distance between platens max.: 900 mm- Opening stroke max.: 650 mm- Ejector stroke: 225 mmInjection unit:- Screw diameter: 45 mm x 18D- Injection volume max.: 230 cm³- Injection part weight: 210 g/hp- Max. injection pressure: 1,670 bar- Screw circumferential speed: 75 m/min- Cylinder heating: 4x 2,200 W- Nozzle heating: 600 W- Connection value: 3x 400 V, 50 Hz- Electrica ...
used
Oven Make: Gallenkamp Model OMT150 XX1.C
used
cross-section width:: Schläuche max. 11 mmcross-section heigth:: 11 mmfeed:: 0,5 - 100.000 mmCondition: used, very good conditionSpecification: universal cutting machine with roller drive for hoses - small cutting machine for hoses- feed unit: roller drive- microcontroller control: 80537- cutting unit: pneumatic- Type of cut: Blade cut- Industrial blade: for PVC hoses- Max. hose diameter: 11 mm- Maintenance unit: yes- Max. feed speed: 1 - 50 m/min - Cutting capacity max.: 450 cuts/min depending on the cutting length- Cutting force approx.: 500 N at 6 bar- Cutting length: 0.5 - 100,000 mm- Resolution/step change: 0.5 mm- Operating voltage: 230V, 50-60 Hz- Compressed air: 5 - 6 bar- Air consumption per stroke approx.: 0. ...
used
Oven Make: Carbolite Model AX60 395mm high x 400mm wide x 420mm deep 220/240 volts Single phase
used
machine measurements: 1500 x 2400 x 1150 mmmachine weight: -- kgpower capacity: 12 kWThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
used
MTS High Frequency Servo Test Rig Load cell Up to 250 kN With hydraulic pump
used
0: 200 °CTorque: - 0Dimensions (HxWxD): 680 x 1320 x 760 mmweight: 177 kgThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
used
Berstorff Three Roll Calender Manufacturer: Krauss Maffei Berstorff 2650mm wide x 650mm (26”) diam. Effective working width 2600mm (Roller Head Die Width) Rolls Configuration: ‘I’ shape Rolls Type: Peripherally Drilled Drive: Right Hand Transmission: Direct Drive by Cardan Shafts Motors: 3X 75 KW, 2600 RPM, 50 Hz Nip Adjustment: Hydraulic (Berstorff patented) Fixed roll: Roll 2 (middle roll) Adjustable roll: Roll 1 and 3 (upper and lower roll), Max Roll gap is 80 mn Cross axis: Roll 1, 2 and 3, Hydraulic operated, max. 25 mm Pre-loading & Roll Bending: Available Rolls Speed: Variable, 0.5-10 m/ min Bearings: Antifriction Roller Bearings Electricals/ Controls: PLC Complete with motor and controls Year 2009
new
screw ø:: 90 mmscrew length:: 20D screw speedl:: 0 - 60 U/minCondition: NEW,Specification: Rubber vacuum extruder - with warranty- Screw diameter: 90 mm- Screw length: L = 20 D (approx. 1,800 mm conveying length)- Screw speed: 0 - 60 rpm- Centre height of extruder: approx. 1,125 mm incl. base frame- Max. permissible injection pressure: 500 bar- with feed roller- Extruder water-tempered- Extruder base frame as welded construction, to accommodate the extruder with drive motor, the temperature control, the vacuum pump- Funnel piece with intermediate flange: two tempering zones approx. 4D = 480 mm- Vacuum cylinder: three tempering zones BL = 1,057 mm- End cylinder: one temperature control zone ...