We use cookies to optimize our website for you and to be able to continuously improve it. By continuing to browse the site you are agreeing to our use of cookies.
Disagree
Manufacturer:
(Category: 503)
used
Shredder Hammel NZS 700 E 250 kW in need of repair
used
machine measurements: -- mmmachine weight: 1.500 kgpower capacity: 30 kWCondition: used,Specification: shredder/Shredding plant with two shredders type: WLK 6 S / 30 V-rotor Weima low and slow speed rotor, and second shredder make: AMIScomplete plant ready for operation, incl. hopper with lidand platform.Special accessories:- automatic star-delta start-up- gear motor with transport screw- lid with limit switch- quick-change sieve- Hopper can be lifted manually- Equipment for underfloor installation consisting of hopper elevation, guard rail, external emergency stop WLK version with sound insulation, sound-insulated lid and front doorTechnical data:- Hopper volume: 0.9 m³- Operating voltage: 3x 400 V- Motor power main drive: 30 kW, 1,500 rpm- Motor power hydraulics: 1.5 / 2.0 kW, 1,500/3,000 rpm- Weig ...
used
- Drum Shredder/Shredder Pallmann - with inlet funnel - Serial number 0806.2006.0017
new
: 600 x 800 mmMotor output: 18,5 kW: 0,6 m³Diameter of the motor: 252 mmDimensions (L/W/H): 1800x1230x1640 mmWeight: 1300 kgThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
used
Einwellenschredder used in the tire recycling as a rubber mill. 2 motors with each 200 kW. Performance 4 t / h truck tyres.
used
recycling shredder: . Number of shafts: 2 : und Plastikmüll weight: 22 tThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
used
Secondary shredder with feed hopper with screw discharge Rotor 1000 mm diameter x 700 mm wide 10 rotor blades, 2 stator knives Motor 110 kW (other motor size available on request)
used
total power requirement: 3,0 kWweight of the machine ca.: 0,5 tdimensions of the machine ca.: 1,6 x 1,4 x 1,6 mSingle shaft shredder cutting system chip shredderPerformance values: Motor cutting unit 3.0 KWTemperature range 15-40 degrees CelsiusVoltage 400VPower consumption 3.0 KWLength x width x height with flat gear 1.50 mm x 575 mm x 315 mmMounted on a mobile base frameincluding mobile/tiltable bucket cartincluding documentationThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
used
Multi-knife mill with 16-blade rotor 6 stator knives Drive 90 kW With accessories
used
WAGNER SINGLE SHAFT SHREDDER WS 70, Only less than 7.000 worked hours, Length:4.680 mm, Width:3.100 mm, Height:2.410 mm, Work area:1.800 x 1.600 mm, Rotor length:1.800 mm (new 2024), Rotor diameter: 588 mm, Number of knives: 104 pc., Drive power: 90 kW, Screen size:40 mm, extraction screw (new 2024), Weight:approx. 12.000 kg, Very good conditions, [Watch Constructors video for this machine](https://www.youtube/watch?v=rDnrhGHvsBQ&ab_channel=WAGNERMasc hinenbauGmbH)
used
Inlet opening: approx. 300 x 600 mm Rotor width: approx. 600 mm Rotor diameter: approx. 300 mm Stator knives: 2 Rotor blades: 4 x 2 Propulsion: 30 kW We have identical machines available. Feed opening: approx. 300 x 600 mm Rotor width: approx. 600 mm Rotor diameter: approx. 300 mm Stator knives: 2 Rotor knives: 4 x 2 Drive: 30 kW We have identical machines in stock.
new
SINGLE SHAFT SHREDDER, 1.000 mm wide rotor, 370 mm diameter, adjustable counter-knife, off-set rotor bearings (low maintenance), V-Rotor with knife pockets, Welded knife holders with screwed knives and covered bold heads, Offset rotor bearings ( low-maintenance / closed ), Fast hydraulic backwards incl. different settings by PLC control and anti shock valve, Shredding room unpainted, Movable screen basket (electro-hydraulically), Screen thickness 10mm, Hydrodynamic starting clutch (energy saving system for machine start), Electromechanical drive with heavy duty gearbox, Control cabinet incl. 5m cable, Electrical control system Siemens S7 PLC control, Reverse counter and transmission limit switch (safety package), Star delta starter, Universal joints for piston with ram impulse and load-related ram function, Machine frame on anti - vibration foundation, Machine prepared for discharge by c ...
used
Inlet: approx. 500 x 490 mm Rotor width: approx. 500 mm Rotor diameter: approx. 300 mm Stator knives: 2 Rotor blades: 3
new
SINGLE SHAFT SHREDDERS SPECIAL FOR PLASTIC SCRAPS, form 600 mm to 2.000 mm wide rotor., Adjustable counter-knives, off-set rotor bearings (low maintenance), V-Rotor with knife pockets, Welded knife holders with screwed knives and covered bold heads, Offset rotor bearings ( low-maintenance / closed ), Fast hydraulic backwards incl. different settings by PLC control and anti shock valve, Shredding room unpainted, Movable screen basket (electro-hydraulically), Screen thickness 10mm, Hydrodynamic starting clutch (energy saving system for machine start), Electromechanical drive with heavy duty gearbox, Reverse counter and transmission limit switch (safety package), Star delta starter, Universal joints for piston with ram impulse and load-related ram function, Machine frame on anti-vibration, Machine prepared for discharge by conveyor belt, Bolted and hardened rotor shaft on gear box side (ant ...
used
For sheets, plates, etc. With horizontal feeder Working width 1050 mm, max. inlet height 50 mm Open rotor 600 mm diameter with 4 blades 2 stator knives Main engine 75 kW
new
SINGLE SHAFT SHREDDER, V-rotor width 600 mm. diameter 260 mm, Rotor speed 80 - 125 rpm, Throughput rate 100-150 kg/h depending on material and screen, Drive power 22 kW, Max. number of knives 28 pcs 40 mm., screen size bespoke to project :15 to 40 mm, Hopper 600 x 800 mm, adjustable counter-knife, off-set rotor bearings (low maintenance), V-Rotor with knife pockets, Welded knife holders with screwed knives and covered bold heads, Offset rotor bearings ( low-maintenance / closed ), Fast hydraulic backwards incl. different settings by PLC control and anti shock valve, Shredding room unpainted, Movable screen basket (electro-hydraulically), Screen thickness 10mm, Hydrodynamic starting clutch (energy saving system for machine start), Electromechanical drive with heavy duty gearbox, Control cabinet incl. 5m cable, Electrical control system Siemens S7 PLC control, Reverse counter and transmiss ...
used
Inlet opening: approx. 600 x 580 mm Rotor width: approx. 580 mm Rotor diameter: approx. 450 mm Stator knife: 3 Rotor blades: 5 Drive: 45 kW Feed opening: approx. 600 x 580 mm Rotor width: approx. 580mm Rotor diameter: approx. 450mm Stator knives: 3 Rotor knives: 5 Drive: 45 kW
new
SINGLE SHAFT SHREDDER, V Rotor width 1.500 mm. Rotor diameter 500 mm 16.69″ Motor power 90 kW n.82 knives 60 x 60, adjustable counter-knife, off-set rotor bearings (low maintenance), V-Rotor with knife pockets, Welded knife holders with screwed knives and covered bold heads, Offset rotor bearings ( low-maintenance / closed ), Fast hydraulic backwards incl. different settings by PLC control and anti shock valve, Shredding room unpainted, Movable screen basket (electro-hydraulically), Screen thickness 10mm, Hydrodynamic starting clutch (energy saving system for machine start), Electromechanical drive with heavy duty gearbox, Control cabinet incl. 5m cable, Electrical control system Siemens S7 PLC control, Reverse counter and transmission limit switch (safety package), Star delta starter, Universal joints for piston with ram impulse and load-related ram function, Machine frame on anti - ...
used
With gebr. Switchboard
new
4-SHAFT SHREDDER 22 KW, sturdy carbon steel electrowelded structure, anti-wear side walls, loading hopper, shredding surface 600 x 800 mm., n.4 x 800 mm long shafts, n.30 anti-wear cutting knives 20 mm thick, n.30 routing disks, n.2 planetary gearboxes, n.2 x 11 kw motors, inversion on overload, n.18 rpm average, bespoke screen size, extraction prepared for connection with blowing system, SIEMENS LOGO PLC with simple panel for complete control, CE compliance, Users manuals.
used
Inlet opening: approx. 100 x 1000 mmm Rotor width: approx. 1000 mm Rotor diameter: 350 mm Stator knife: 2 Rotor blade: 3 Drive: 30 kW Feed opening: approx. 100 x 1000 mm Rotor width: 1000 mm Rotor diameter: 350 mm Stator knives: 2 Rotor knives: 3 Drive: 30 kW
new
4-SHAFT SHREDDER 15 KW, sturdy carbon steel electrowelded structure, anti-wear side walls, loading hopper, shredding surface 600 x 800 mm., n.4 x 800 mm long shafts, n.30 anti-wear cutting knives 20 mm thick, n.30 routing disks, n.2 planetary gearboxes, n.2 x 7,5 kw motors, inversion on overload, n.18 rpm average, bespoke screen size, extraction prepared for connection with blowing system, SIEMENS LOGO PLC with simple panel for complete control, CE compliance, Users manuals.
used
Two-shaft shredder Drive 37.50 kW
new
TWIN-SHAFT HYDRAULIC SHREDDER, Hopper size: 2.5 x 1.8 x 1.2 m (or customised), construction in robust high thickness carbon steel, shredding surface 1.500 x 1.100 mm, 2 counter-rotating steel hexagonal shafts with differentiated speed 16-21 rpm, no. 30 blades, 50 mm, 2 teeth, very easy blade maintenance, welded profile connection frame 1.3 x 1.0 x 1.5 m approx., No. 2 gearboxes, No. 2 electric motors 37,5 kW ( 100 Hp) total power - 400 V/50 Hz, bearings strategically positioned so as not to be affected by the processed material, the bearings are connected to a centralised lubrication point that can be connected (as an option) either to an automatic lubrication system or to a manual greasing point where the operator can intervene regularly., hydraulic control unit,, electrical control panel with PLC and machine wiring, automatic overload reversal with programmable number of reverse cycles ...
used
Inlet: approx. 1600 x 1600 mm Rotor width: approx. 1600 mm Rotor diameter: approx. 560 mm
new
SINGLE SHAFT SHREDDER, V Rotor width 2.000 mm. 78,74 Rotor diameter 500 mm 16.69″ Motor power 90 kW n.112 knifes 60 x 60, adjustable counter-knife, off-set rotor bearings (low maintenance), V-Rotor with knife pockets, Welded knife holders with screwed knives and covered bold heads, Offset rotor bearings ( low-maintenance / closed ), Fast hydraulic backwards incl. different settings by PLC control and anti shock valve, Shredding room unpainted, Movable screen basket (electro-hydraulically), Screen thickness 10mm, Hydrodynamic starting clutch (energy saving system for machine start), Electromechanical drive with heavy duty gearbox, Control cabinet incl. 5m cable, Electrical control system Siemens S7 PLC control, Reverse counter and transmission limit switch (safety package), Star delta starter, Universal joints for piston with ram impulse and load-related ram function, Machine frame on ...
used
Rotor width: approx. 300 mm Rotor diameter: approx. 300 mm Stator knife: 6 Rotor blade: 9
used
VECOPLAN VAZ 220/200 KNF, single shaft shredder for plastics, constructed in 2000, imfeed width 2200 mm, working width: 2000 mm, Rotor Ø 495 mm, n.56 knives size 60 x 60 mm., Rotor speed 125 rpm, 132 kW drive, 400V 50 Hz, Machine weight : about 14 tons, Upper ram, feeding hopper, various screens available, Electrical panel, Users manual, drawings available, This machine is offered totally reconditioned, (last group of photos is of a twin machine just reconditioned), width: 2.000 mm. (78.74), Power: 132kw
used
Inlet opening: approx. 400 x 600 mm Rotor width: approx. 600 mm Rotor diameter: approx. 500 mm Stator knife: 3 Rotor blade: 5 x 2 Drive: 55 kW
used
WEIMA WLK 18 SJ SUPER JUMBO SINGLE SHAFT SHREDDER, Totally refurbished in 2020 with replacement of electric circuits + motor + rotor + board .., 219 worked hours after refurbIshing, loading hopper 1.800 x 1.880 mm., hopper capacity approx 5,4 m3, rotor width 1.800 mm, rotor diameter 482 mm, 100 rpm, 75 kw drive, weight : about 12.000 kg, installed power : 75