We use cookies to optimize our website for you and to be able to continuously improve it. By continuing to browse the site you are agreeing to our use of cookies.
Disagree
121,949 used machines on RESALE, but how to find them? Machine Search
used
Comments: 30k done by INNIO Item Code: 1112770u Scope: Genset manufacturer: Jenbacher Engine Type: JMS Engine Serie: 624 Gas Type: Natural Gas Design No: K706 Eng Ser No: 1038017 Unit Ser No: 1038011 Orig Po Output kWe: 4401 Orig PoOutput kWm: 4491 Orig Voltage(V): 6300 YoM: 2011 OH stop OP: 44493 powerup.at - Technology is our drive. Efficiency our focus.
used
Item Code: 1110657u Scope: Genset manufacturer: Jenbacher Engine Type: JGS Engine Serie: 620 Gas Type: Natural Gas Design No: E728 Eng Ser No: 5534301 Unit Ser No: unknown Orig Po Output kWe: 2731 Orig PoOutput kWm: 2807 Orig Voltage(V): 11000 YoM: 2008 OH stop OP: 52443 powerup.at - Technology is our drive. Efficiency our focus.
used
Comments: Gastrain has been used for different project at 60k Engine and Alternator was exchanged. At 120k oh Jenbacher performed a life time extension. At 130k Jenbacher did a 10k Serice intervall. Since last Service Intervall only 2k Service Steps done. Item Code: 1110609u Scope: Genset manufacturer: Jenbacher Engine Type: JMS Engine Serie: 312 Gas Type: Biogas Design No: B918 Eng Ser No: 1215850 Unit Ser No: 4201831 Orig Po Output kWe: 500 Orig PoOutput kWm: 657 Orig Voltage(V): 400 YoM: 2012 OH stop OP: 147000 powerup.at - Technology is our drive. Efficiency our focus.
used
Comments: Vers. S21, komplett überholt, Turbolader fehlt, kann auf Erdgas geändert werden. Ohne Steuerung Item Code: 1108737 Scope: Genset manufacturer: Jenbacher Engine Type: JGS Engine Serie: 320 Gas Type: Biogas Design No: 5803 Eng Ser No: 1200286 Unit Ser No: 2679581 Orig Po Output kWe: 1003 Orig PoOutput kWm: 1034 YoM: 1997 powerup.at - Technology is our drive. Efficiency our focus.
used
Servo motor, permanent magnet motor, water-cooled SIEMENS 1PH4138-4NF26 30 kW 1500 rpm 244 V IP65 Shaft: Ø 42 mm Wavelength: 110 mm flange: 250 x 250 mm, hole spacing: 212 mm, Holes: Ø 18 mm used, tested ! Dimensions: 730 x 265 x 340 mm
used
no tank included air delivery: 78 liter/sec max speed: 1500 r/min Max output: 10 bar Low press. (1) High press (2) Screw (3): Screw Power imput: 37 kWt
used
Bausch + Stroebel - fully automatic line for washing, drying/sterilising, filling & closing of cartridges comprising: B+S KWM 10000 washing machine with ultra sonic cleaning, container diameter from 7 up to 15 mm, max. container height 90 mm, capacity up to 30,000 cartridges per hour B+S DHT 2550 hot air sterilizing tunnel, conveyor width 500 mm, total length approx. 2770 mm, width approx. 1700 mm, height approx. 1900 mm, output up to 73 kg per hour B+S KFM 8024 filling & closing machine, continuous motion, insertion of plunger stoppers – insertion of mixing balls – gas-flushing before dosing – dosing using ceramic rotary piston pumps (6-head pre-dosing station + 6-head post-dosing station) – closing the cartridges with rubber lined crimp caps – magazine out feed, dosing range 0.1 – 500 ml, container diameter from 7 up to 14 mm, max. container height 90 mm, CIP/SIP-System, ...
used
General SKU354T1031 LocationBarneveld MakeVemag TypeHP Coex No.1720136 Year of construction2020 Main Features MaterialStainless steel Number of1 heads Specified Features - Piston filler MaterialStainless steel 1.4301 (304) Filling linecheck Dosingup to 280 kg/h Number of filling heads:1 (with: double screw and feed unit) With hoppercheck (105 Ltr.) Inletdia. 60mm Motor1,3 kW With switchcheck Mounted on wheelscheck Floorspace0,97x0,64 m Total height2,15 m Information Weight300 kg CEcheck Extra Specificationswith vacuum pump: motor: 0,55 kWPiston fillersVemagPackaging machines > Piston fillersBrand > Vemag What you can expect from Foeth: -- Machine is in working condition -- At a reduced price compared to new -- Ready for shipping to any destination worldwide -- You are welcome to inspect the machine in Barneveld, The Netherlands. Please visit us in Barneveld for ...
used
General SKU300U1009 LocationBarneveld MakeLauda TypeRK 20 No.9292 / 504 491 Main Features MaterialStainless steel Heating (medium)Electric Capacity2.3 KW Temp.20 °C Specified Features - Temperature control unit MaterialStainless steel Temperating machinecheck Electric heatingcheck With coolingcheck Capacity2.3 kW Temperature -40°C to 20°C With temperature controllercheck With controlcheck Temperature control units Capacity2,3 kW Information Year of construction1987 Total height0,70 m Weight50 kg With switchcheck Floorspace0,43x0,47 m Extra SpecificationsWith MGW temperature controller, type RKT20: temperature range: from -40°C to 20°C: capacity: 2.3 kWTemperature control unitsLaudaHeat exchangers > Temperature control unitsBrand > Lauda What you can expect from Foeth: -- Machine is in working condition -- At a reduced price compared to new -- Ready for s ...
used
General SKU345S531 LocationBarneveld MakeFima Verfahrenstechnik (DE) TypeTZT-1300 No.88789/2 Year of construction1999 Pressure Working pressure3 Bar Main Features MaterialStainless steel Motor55 KW Inlet diameter40 mm Specified Features - Basket centrifuge Basket centrifugeHorizontal Capacity800 Ltr. Basket sizesdia. 1300x600mm Wall thickness15 mm Max. loading weight380 kg Mechanical operatedcheck Motor55,0 KW, 400 Volt (Ex) With variable speed drivecheck Max. basket speed900 rpm MaterialStainless steel 1.4404 (316L) Information Mounted on framecheck Total height2,8 m Weight± 9000 kg Floorspace3,8 x 1,9 m Extra SpecificationsFilter area: 2,4 m² Max. temp.: 150 °C Product outlet: DN40 Product inlet: DN40 with: braking resistor: Frizlen, type: FA 3247002, 35 kWBasket centrifugesFima ProcessCentrifuges > Basket centrifugesBrand > Fima Process What you can e ...
used
General SKU031H069 LocationBarneveld MakeAPI Schmidt-Bretten TypeSigma X49 SCL No.PA-087714 Year of construction2005 Pressure Working pressure10 Bar Main Features MaterialStainless steel Surface146.8 m2 Size length1100 mm Sizes width400 mm Specified Features - Plate heat exchanger MaterialStainless steel 1.4301 (304) Plate heat exchangers(1x) Heating surface146,8 m2 Capacity142/143 Ltr Number of platens360 Plate sizes± 1100x400mm Connections4x dia. 100mm Max. temperature100 Degr. C. Capacity900 KW Information Floorspace2,5x0,8 M Total height1,6 M Weight1500 KG Extra Specificationssealing material NBR Technical specs Extra informationindicated size is platen size, capacity is 900 KWPlate heat exchangersApi SchmidtHeat exchangers > Plate heat exchangersBrand > Api Schmidt What you can expect from Foeth: -- Machine is in working condition -- At a reduced pric ...
used
General SKU261S250 LocationBarneveld Makeunknown, manufacturer plate is missing Main Features MaterialStainless steel Motor0.75 KW Inlet diameter245 mm Specified Features - Metering screw Metering screwcheck Screw diameter180mm (1x), 80mm (1x) Pitch120mm, 60mm Shaft diameter50mm, 20mm Screw length1300mm With hoppercheck Hopper sizes590x400x550mm Inletdia. 245mm Outletdia. 250mm With motor(screw 180) 0,75 kW, (screw 80mm) 0,37 kW220-240/380-420 volt Screw speed78 rpm (180mm screw), 80 rpm (80mm screw) With breaking/mixing shaftcheck Motor0,55 kW 220-240/380-420 volt Metering screws MaterialStainless steel Information Floorspace2,2x1,6 M Total height4,1 M Weight1050 KgMetering screws-Dosing units > Metering screwsBrand > - What you can expect from Foeth: -- Machine is in working condition -- At a reduced price compared to new -- Ready for shipping to any destina ...
used
General SKU247S159 LocationBarneveld MakeLipp Mischtechnik GmbH (D) TypeIMR-E 2000 No.4920 Year of construction2011 Pressure Working pressure10 Bar Vacuum possiblecheck Main Features MaterialStainless steel Volume2090 Ltr. Motor55 KW Specified Features - Powder turbo mixer Powder turbo mixercheck Capacity2090 ltr. Trough sizesdia. 1100x2200mm InletDN200 Inspection hatchdoor dia. 1100mm OutletDN200 Max. temperature-40/120°C Motor55 kW400/690 Volt (Ex) Speed mixing shaft50 rpm With lump breaker(3x) Motor15 kW 400/690 Volt (Ex) (3x) Speed lumpbreaker965 rpm MaterialStainless steel 1.4571 (316Ti) Information Mounted on framecheck Total height2,3 M Weight7500 Kg CEcheck Floorspace2,5x4,7 M ATEX compatiblecheck Extra Specificationsshaft seals by means of a flushed seal (Eagle Burgmann) including filter and product dosing vessel with agitator Powder turbo mi ...
used
General SKU345S530 LocationBarneveld MakeFima Verfahrenstechnik (DE) TypeTZT-1300 No.Z00033 Year of construction1994 Pressure Working pressure3 Bar Main Features MaterialStainless steel Motor55 KW Inlet diameter40 mm Specified Features - Basket centrifuge Basket centrifugeHorizontal Capacity800 Ltr. Basket sizesdia. 1300x600 mm Wall thickness15 mm Max. loading weight200 kg Mechanical operatedcheck Motor± 55 kW With variable speed drivecheck Max. basket speed900 rpm MaterialStainless steel 1.4571 (316Ti) Information Mounted on framecheck Total height2,55 m Weight± 9000 kg Floorspace3,4x2,5 m Extra SpecificationsFilter area: 2,4 m² Max. temp.: 100 °C Product outlet: DN40 Product inlet: DN40 with: braking resistor: Frizlen, type: FA 3247002, 37,7 kWBasket centrifugesFima ProcessCentrifuges > Basket centrifugesBrand > Fima Process What you can expect from F ...
used
General SKUR1397 LocationBarneveld MakeVakumix AG (DE) TypeHM2-008 with lid-lifting device No.1033070 Mach.No.1033070 Pressure Working pressure4 Bar Vacuum possiblecheck Working pressure jacket6 Bar Main Features MaterialStainless steel Volume3.1 Ltr. Motor5.5 KW Specified Features - Processing vessel MaterialStainless steel 1.4404 (316L) Processing vessels Capacity3.1 Ltr Closed stirring vesselcheck Capacity3,1 Ltr (Nett.2,5-2,0 Ltr ) Vessel sizesdia. 150x160mm Dished bottomcheck Dished top sidecheck With covercheck Outletdia. 25mm With jacket(0.44 Ltr) Max. temperature180 degr.C. With anchor stirrercheck Motor0.37 KW, 400 Volt Speed mixing shaft10-410 rpm With homogeniser(500 - 14000 rpm) Motor5.5 KW, 400 Volt Information Year of construction2004 Total height1,9 M Weight300 Kg CEcheck With switchcheck Floorspace1,0x1,0 M Extra Specificationsincl ...
used
Complete with Lns Quick Load Servo Iii bar loader Max Distance between Tips mm. 970 / Min. mm. 210 Max Turning Diameter mm. 190 Main Spindle: Spindle Nose (Asa Attachment) Asa A2-6 Spindle speed (Min./max.) Rpm/min. 4,500 Spindle Motor Power Kw Kw. 11/15 Bar passage mm. 65 Counter spindle Spindle Nose (Asa Attachment) Asa A2-5 Spindle speed (Min./max. )g./min. 5,000 Spindle Motor Power Kwkw. 11/7.5 Bar passage 51 mm Number of upper turrets 2 Number of Lower Turrets 1 X Axis Travel mm. 167.5 Z Axis Stroke mm. 250 Y Axis Travel mm. 102 X Axis Travel 2mm. 167.5 Z Axis travel 2mm. 250 Y Axis travel 2mm. 102 X Axis Travel 3mm. 167.5 Z Axis travel 3mm. 685 Fanuc 16i-tb control Dimensions W D Hmm.3.930 X 2.270 X 2.110 2 High Pressure Pumps Paper Filter Conveyor Finished Pieces External mat Weight 12,000 kg Year 2004
used
Operating Instructions FMB Machining Center / Version 9. June 2011. Machining centres Software from Schüco installed Software design Special machines Operating instructions 7. technical data 7.1Machine dimensions Total length mm 9,750 Total depth / with LS mm2.750 / 3.300 Total height max. mm4.100 7.2 Axle travel X-axis mm approx. 7,100 Y-axis mm approx. 1,480 Z-axle bucket 710 V-axis (optional)mmca 6,980 A axis (optional)degrees180 ° Gajs30zga C axis (optional)degree360 ° W-axis (optional)mm 7.3Working spindle Spindle drive kW7.5 Spindle speedmin-120.000 Spindle mounting HSK E40 7.4Tools Mounting HSK E40 Wkzg positions 6 (more optional) 12 Wkzg maximum diameter mm 35 Saw blade Ø for milling spindle mm 400
new
(3) 2011 Caterpillar C280-8 Offshore Gensets (Unused) - Serial No.: PKA00151, PKA00152, PKA00153 - Model: C280-8/I-8, 4-Stroke-Cycle-Diesel - Rated Speed: 900 RPM - Generator: KATO ENGINEERING INC. - Model: AA28661000 - Potency: 3.142.9 Kwa / 2.200 Kw - 60Hz, 346/600 Volts, 3 Phase - Emissions/Fuel Strategy: EPA Tier 2, IMO II
used
Additional title: Compact cooling unit with ice water reservoir, Cold storage: 184 kWh, Vessel volume: 3300 l, Max. operating pressure: 26 bar, Power: 21 kW (electrical), Current: 38,5 A, Voltage: 400 V / 3 phases, Frequency: 50 Hz, Length: 3650 mm, Width: 1510 mm, Height: 1900 mm, Weight: 2200 kg, Base construction: standing on frame, Periphery: evaporating condenser: manufacturer: Güntner, type: GBH 30 Liter
used
Description: Serial number 28830003092, operating hours read 47641, main drive: infinitely variable 0 to 8000 rpm, torque max. 191 Nm, spindle motor max. 20 kWh, feed range 1 to 40000 mm/min, rapid traverse 1 to 40000 mm/min, 2 pallets 400 x 500 mm, max. pallet load 600 kg, travel X 600 mm, Y 560 mm, Z 560 mm, B 360°, tool holders SK 40, tool magazine with 40 places, including accessories, SIEMENS SINUMERIK 840 D control unit weight approx.: 12,000 kg, Approx. Onsite Dimension. (l x w x h): 5,000 x 4,800 x 2,800 mm
used
Description: Year of construction: 05/2008 Volume flow: 1000 m3/h Supply voltage: 230 V Control voltage: 24 V Frequency: 50 Hz Motor power: 1.1 kWkg Approx. Onsite Dimension. (l x w x h): 1,570 x 800 x 550 mm, weight approx.: 100 kg
used
Comments: Important: orig. Alternator used for different project. PowerUp did a condition based 60k, Liner, Piston, Conrod, Bearings have not been changed. Engine overall in best condition, accord. OEM 60k overhaul should be performed. Item Code: 1111043 Scope: Genset manufacturer: Jenbacher Engine Type: JMS Engine Serie: 620 Gas Type: Natural Gas Design No: F040 Eng Ser No: 5650841 Unit Ser No: 5649823 Orig Po Output kWe: 3019 Orig PoOutput kWm: 3119 YoM: 2009 OH stop OP: 73058 powerup.at - Technology is our drive. Efficiency our focus.
used
Comments: Deposit Engine, LB only, 60koh, Item Code: 1113620u Scope: Longblock manufacturer: Jenbacher Engine Type: J Engine Serie: 312 Gas Type: Biogas Design No: I538 Eng Ser No: 1016062 Unit Ser No: 1016077 Orig PoOutput kWm: 657 YoM: 2011 OH stop OP: 60000 powerup.at - Technology is our drive. Efficiency our focus.
used
Comments: Serviced the entire life time by authorized Service Partner in France. Item Code: 1107931u Scope: Genset manufacturer: Jenbacher Engine Type: JMS Engine Serie: 612 Gas Type: Natural Gas Design No: A176 Eng Ser No: 3154901 Unit Ser No: 3154931 Orig Po Output kWe: 1464 Orig PoOutput kWm: 1500 Orig Voltage(V): 400 YoM: 2000 OH stop OP: 40000 powerup.at - Technology is our drive. Efficiency our focus.
used
Comments: PUP Genset Item Code: 1111827 Scope: Genset manufacturer: Jenbacher Engine Type: JGS Engine Serie: 320 Gas Type: Natural Gas Eng Ser No: 1003596 Orig Po Output kWe: 1006 Orig Voltage(V): 400 YoM: 2024 powerup.at - Technology is our drive. Efficiency our focus.
used
Comments: Important: orig. Alternator used for different project. PowerUp did a condition based 60k, Liner, Piston, Conrod, Bearings have not been changed. Engine overall in best condition, accord. OEM 60k overhaul should be performed. Item Code: 1111042 Scope: Genset manufacturer: Jenbacher Engine Type: JMS Engine Serie: 620 Gas Type: Natural Gas Design No: F040 Eng Ser No: 5649831 Unit Ser No: 5649821 Orig Po Output kWe: 3019 Orig PoOutput kWm: 3119 YoM: 2009 OH stop OP: 71813 powerup.at - Technology is our drive. Efficiency our focus.
used
Comments: with Control System but without Alternator. Previous owner had full CSA Contract with Inni Spain, 60k was not done Item Code: 1113332u Scope: Genset manufacturer: Jenbacher Engine Type: JMS Engine Serie: 620 Gas Type: Natural Gas Design No: E806 Eng Ser No: 1216621 Unit Ser No: 5578962 Orig PoOutput kWm: 3072 YoM: 2008 OH stop OP: 60000 powerup.at - Technology is our drive. Efficiency our focus.
used
Comments: PUP Genset Item Code: 1111826 Scope: Genset manufacturer: Jenbacher Engine Type: JGS Engine Serie: 320 Gas Type: Natural Gas Eng Ser No: 6628391 Orig Po Output kWe: 1006 Orig Voltage(V): 400 YoM: 2024 powerup.at - Technology is our drive. Efficiency our focus.
used
Comments: PUP Genset Item Code: 1111825 Scope: Genset manufacturer: Jenbacher Engine Type: JGS Engine Serie: 320 Gas Type: Natural Gas Eng Ser No: 1072886 Orig Po Output kWe: 1006 Orig Voltage(V): 400 YoM: 2024 powerup.at - Technology is our drive. Efficiency our focus.
used
Key data: 53 KW, 66 kVA, 400 V
SDMO Diesel Emergency Generator Set R66C3 IV Diesel emergency power from 2016 with 683 operating hours (last maintenance 2022), complete (closed module). 1 available 52.8 KWel x 1,500 rpm, 400/230 V / 50 Hz. AC generator: Leroy Somer LSA 42.3 L9, 66 KVA Manufacturer: SDMO Model: R66C316002688 Type: Diesel Emergency Power Motor: SDMO 4045HFS85 Engine power [KW]: 53 AC Generator: Leroy Somer LSA 42.3 L9 AC generator power [KVA]: 66 Voltage [V]: 400/230 Frequency [Hz]: 50 Electricity [A]: 87 Speed [1/min]: 1,500 Switchgear: SDMO R66C3 Year of construction: 2016 Hours: 683 Total weight [kg]: 2,040 / 1,654 net Dimensions LxWxH [cm]: 255x115x182
used
Comments: Deposit Engine, LB only, 60koh, Item Code: 1113007u Scope: Longblock manufacturer: Jenbacher Engine Type: J Engine Serie: 316 Gas Type: Natural Gas Design No: 6079 Eng Ser No: 1227920 Unit Ser No: 289561 Orig PoOutput kWm: 827 YoM: 2007 OH stop OP: 60000 powerup.at - Technology is our drive. Efficiency our focus.
used
Comments: 380V / 60 Hz no Control Cabinet, no Gas Train Item Code: 1112984u Scope: Genset manufacturer: Jenbacher Engine Type: JMS Engine Serie: 316 Gas Type: Natural Gas Design No: B149 Eng Ser No: 410898 Unit Ser No: 3775821 Orig Po Output kWe: 846 Orig PoOutput kWm: 876 Orig Voltage(V): 380 YoM: 2003 powerup.at - Technology is our drive. Efficiency our focus.
used
Description: Lot composed of 5 pallets of 70 bags of pellets each Weight 15 kg per bag Diameter 6 +/- 1 mm Length 3.15 - 40 mm Heating power >, 4.6 kWh/kg EN plus - A1 certificates ATTENTION! PICKUP POSSIBLE ONLY ON APRIL 29-30 Approx. Onsite Dimension. (l x w x h): 2,400 x 3,600 x 1,600 mm, weight approx.: 6,600 kg
used
Description: Lot composed of 5 pallets of 70 bags of pellets each Weight 15 kg per bag Diameter 6 +/- 1 mm Length 3.15 - 40 mm Heating power >, 4.6 kWh/kg EN plus - A1 certificates ATTENTION! PICKUP POSSIBLE ONLY ON APRIL 29-30 Approx. Onsite Dimension. (l x w x h): 2,400 x 3,600 x 1,600 mm, weight approx.: 5,500 kg
used
Description: Lot composed of 5 pallets of 70 bags of pellets each Weight 15 kg per bag Diameter 6 +/- 1 mm Length 3.15 - 40 mm Heating power >, 4.6 kWh/kg EN plus - A1 certificates ATTENTION! PICKUP POSSIBLE ONLY ON APRIL 29-30 Approx. Onsite Dimension. (l x w x h): 2,400 x 3,600 x 1,600 mm, weight approx.: 6,600 kg
used
Description: Lot composed of 5 pallets of 70 bags of pellets each Weight 15 kg per bag Diameter 6 +/- 1 mm Length 3.15 - 40 mm Heating power >, 4.6 kWh/kg EN plus - A1 certificates ATTENTION! PICKUP POSSIBLE ONLY ON APRIL 29-30 Approx. Onsite Dimension. (l x w x h): 2,400 x 3,600 x 1,600 mm, weight approx.: 5,500 kg
used
Description: Lot composed of 5 pallets of 70 bags of pellets each Weight 15 kg per bag Diameter 6 +/- 1 mm Length 3.15 - 40 mm Heating power >, 4.6 kWh/kg EN plus - A1 certificates ATTENTION! PICKUP POSSIBLE ONLY ON APRIL 29-30 Approx. Onsite Dimension. (l x w x h): 2,400 x 3,600 x 1,600 mm, weight approx.: 5,500 kg
used
Description: Complete REMKO heat pump heating system with 120 kW output for heating and cooling for warehouses up to 2,000 m², incl. all accessories such as control unit, heat exchanger, small items etc. Scope of delivery: RK WP SQW 400 WB Triple Alu, Cologne heating/cooling package RK multifunctional buffer cylinder, MPS 2000 K heating/cooling 270440 RK WP SQW 400 WB Triple Alu, L/W Monobloc heat pump 300020 3 pieces RK Smart-Start units, 2 built-in, SQW 400 WB 301020 3 pieces RK Smart-Start,2 built-in, SQW 400 WB 301030 3 pieces RK Low-Noise, built-in, additional sound insulation SQW 400 301040 3 pieces RK frost protection heater SQW/LWM, hydraulic module, built-in 301050 3 pieces RK SQW vibration dampers, for decoupling the system 301060 3 pieces RK pipe connection set, installed RK pipe connection set HZ SQW 400, connection for triple cascade 301003 Flange surface-mo ...
used
Description: Control: ,Easy Control Speed-controlled track control with optical start-stop indication sensors Control screen LCD Ergonomically integrated on the input side on the hood YouTube Configuration Chain conveyor transport Central lubrication Above pressure/guidance Via central adjustment with 2 rows of rollers positioned in offset to each other Loading unit A3 labeling unit for hot melt and possibility of PU lubrication Lubricating roll under workpiece in travel or counterflow machete in weighted version Pressure zone Pneumatically rotated 1st pressure roller 2nd roller free-running ensures good compaction Capacities:2 0.18 KWW 12,000 rpm Radial free Chamfer/radius2 0 27 KW in backlash 200Hz 12,000 rpm equal 3 positions, manual adjustment siko counters max 3 mm edge banding Profile scrapers Quick-change system max 3 mm edge banding Chain width: 80 ...
used
Description: Heavy load trailer with - Double turntable steering - small turning circle - Tilt-safe as steering angle limit - robust, low maintenance - Reversible drawbar - 50mm impregnated wood overlay. Pick up only from KW10/11 possible Capacity 10000 kg Length 6000 mm Width 2500 mm Height 595 mm Rear axle: steerable Front axle: steerable Machine weight approx. 1,3 t Space required approx. 6.7 x 2.5 x 0.725 Approx. Onsite Dimension. (l x w x h): 6,700 x 2,500 x 600 mm, weight approx.: 1,330 kg
used
Description: 11.63 KWp solar panels 150 x used thin-film solar modules with a nominal output of 72.5 Wp-77.5 Wp per solar module. Total power : 10,875 Wp / 10.88 KWp - 11,625 Wp / 11.63 KWp Packed on 3 pallets of 50 pieces. Technical data solar panel: Nominal output per pallet: approx. 3,625 Wp / 3.63 KWp - 3,875 Wp / 3.88 KWp Dimensions solar module: approx. 1,200 mm x 600 mm x 6.8 mm Pallet dimensions: approx. 1,400 mm x 1,100 mm x 860 mm Weight per module: approx. 12 kg Weight per pallet: approx. 635 kg Total weight: approx. 1,905 kg Packages: 3 pieces Illustration similar. Due to the weather, the modules can become soiled, but these are easy to clean. German EEG has expired. Approx. Onsite Dimension. (l x w x h): 1,400 x 3,300 x 900 mm, weight approx.: 1,900 kg
used
Description: Fabrication number: S6AY1201 Operating voltage: 3 x 400 V Frequency: 50/60 Hz Rated current: 80 A Control system: SIEMENS SINUMERIK 840 D Turning length: approx. 550 mm Center distance: approx. 680 mm Rotation diameter: approx. 500 mm max Turning diameter over bed: approx. 610 mm Travel paths: X: approx. 300 mm Z: approx. 600 mm The machine is equipped with a 12-position tool turret including driven tool stations as well as a C-axis, a tailstock and a three-jaw chuck (diameter: 230 mm) from the manufacturer SMW-AUTOBLOK Also incl. filter extraction system from the manufacturer LTA and a cooling system from the manufacturer KELVIN Type: KW570.00.CA 0187 Year of manufacture: 2008 And a chip conveyor from the manufacturer KNOLL Year of construction: 2010 weight approx.: 7,000 kg, Approx. Onsite Dimension. (l x w x h): 4,500 x 1,800 x 2,200 mm
used
Everun ER06 farm loader NEW! without minimum priceOperating hours may change minimally as a short test drive is possible during inspection.Year of construction 2023Operating hours 1 hourSerial number 221362Technical data:Engine model Kubota D1105 EPA4/Euro5 engineShovel capacity 0.26 m³Floating position of the lifting armLoad capacity 600kg according to the manufacturing information -> but also lifts a 1.25m round silage bale with the pallet forkNet weight 2000kgLifting time ? 8.0 sMaximum speed 12 km/hMinimum. Turning radius 2466 mmRated power 18.2 kWIdle speed 850-900 (rpm)Rated speed 3000 rpm (rpm)Max. rotation angle ±35°Total length (bucket on floor) 3676 mmTotal height 2220 mmTotal width 1150 mmDumping height 1764 mmDumping reach 829 mmWheelbase 1378 mmTires 2612-12 agricultural tires
used
Manitou 120AETJC electric stage from 2017 with 386 hours.Test drive possible during the inspection, the operating hours will change a little.Technical data:Working height 11.95 mLoading area length 1.2 mLoading area width 0.92 mTransport length 3.74 mTransport width 1.2 mTransport height 2.16 mOwn weight 6550 kgPayload 200kgRange 7 mPeople 2max. climbing ability 25%Driving speed 6 km/hTurning radius outside 3.25 mAETJ seriesRated power of the electric motor2 x 4.50 kWElectric emergency pump3.70kWbattery48VRated battery voltage / battery capacity48Vx240AhBattery energy11 kWhIntegrated charger48V/30AThe machine can be purchased via Buy It Now or via Price Suggestion!Machine is functional so far..
used
Description: Vertical travelling column machining centre Machine number: F 44 088 Drive power: 23 kW (three-phase current) Rapid traverse: 0-30 m/min (Z-axis 20 m/min, C-axis 6 m/min) Milling head position: Vertical / horizontal Chip conveyor: Tecnimetal Tool changer: Kekeisen KWVA 48 Throughfeed recooling unit: BKW Edge splitting filter: Mahle Pi 72 NC rotary table Radio measuring station: M&,H 20.00 Internal coolant supply z-motion: 800 mm, x-motion: 1,200 mm, y-motion: 650 mm, control: Heidenhain TNC 430 M, taper: SK 50, toolchanger positions: 48, turning speed range: 20-7300 rpm, feed range: 0-5000 mm/min, total power requirement: 50 kW, weight approx.: 17,000 kg, Approx. Onsite Dimension. (l x w x h): 5,300 x 5,300 x 3,300 mm
used
Wartsila 3.9 MW/50Hz Gas Generating Set 12V34SG with CHP Auxiliaries This power plant was built by Wartsila in end of year 2010 and it was commissioned in 2011 as a turn-key project with heat recovery system for 10 bar steam production. Fuel used in this plant was normal natural gas fed from a local pipeline. The plant was operated till 2021 having total operating hours 43’767 till shutting down. Complete plant with step up transformer, lube oil system, control panels, and synchronizer panel, USP systems, operating monitors, MCC, start system and air compressors, HRCS for 10 bar steam, exhaust system, 6 kV Vacuum breaker with synchronisation, manuals and drawings. Plant is still installed, and electric power is still connected to all devices. Wartsila Service has made all scheduled services for this engine, last 40’000-hour service just 3000-hour prior operation closing in 2021. ...
used
Used MITECO 30,000 l/h Soft Drink Blending Plant Manufacturer: Miteco Model: Soft Drink Blending Plant Available Immediately The plant is designed for the continuous blending of soft drinks made of different fluid-streams. Original documentation available. Consists of units as listed below. Also c/w various pumps, pipework and control panels. Consisting Parts: CIP Skid Unit x2 Type: CIP 40 Serial: 36.1806.1.0 Year of Manufacture: 1999 Order: B99.11.2180/1 Cleaning Liquid Output Max: 30,000 l/h Cleaning Liquid Backflow Max: 30,000 l/h Water Temp: 20-30 C Heating Power: 700kW Cleaning Temp Max: 85 C Continew Skid Unit x2 Type: CN 5-30FB Serial: 38.1602.0.0 Year: 1999 Order: B98.10.1950/1 Output Max (Coca Cola): 30,000 l/h Concentration Range: 0 - 13 Brix Accuracy: 0.05 Brix Temperature Range: 9 - 18 C Sugar Solution Temp: 20 - 25 C Cleaning Temp: 85 C CO2 Pressure Max: 1 ba ...
used
Baujahr 2018Kubota KX080-4a aus 2018 mit 6483,5 Stunden mit englischen Schnellwechsler wird verkauft wie auf den Bildern zu sehen ist ohne Schaufeln. Betankungspumpe vorhanden!Fast nicht ausgeschlagen, nur beim Hauptzylinder unten die Buchse und eventuell der Bolzen.Klimaanlage vorhanden und funktionstüchtig sowie die Heizung.Hydrauliköl mit Filter wurde gewechselt bei knapp 6000 Std sowie der Luftfilter bei 6266 Stunden wie auf den Bildern zu erkennen ist. Bagger läuft ansonsten wie auf dem Video zu sehen ist.Eigengewicht8.19 tTransportlänge6.45 mTransportbreite2.2 mTransporthöhe2.54 mTieflöffel-Inhalt0.25 m³Kettenbreite450 mmAuslegerMBReichweite7.33 mGrabtiefe4.6 mAusbrechkraft65.2 kNTieflöffelbreite0.8 mSerienKXMotorherst.KubotaMotortypeV3307CR-TE4Motorleistung46.5 kWHubraum3.331 lDrehzahl bei max. Drehmoment2000 rpmZylinderanzahl4Zylinder Bohrung x Hub94x120 mmGerne anfragen ...
used
Year of production / SO / GO: 1987 / - / 1997 Technical parameters of the machine: Maximum torque on the spindle - 1000 NMMaximum feed force in the X, Y, Z axes - 25,000 NMMaximum workpiece weight - 2,000 kgTotal table area (with grooves) - 630 x 2200 mmNumber of table T-slots - 5Width and T-pitch Table grooves - 22 x 100 mmTable height from base - 900 mmLongitudinal table stroke X - 1,500 mmTransverse table stroke Y - 630 mmVertical headstock stroke Z - 630 mmSpindle taper - ISO 50Spindle diameter in front bearing 110 mmSpindle face distance from table clamping surface - 150 -780 mmSpindle motor - regulatingMotor power S119.3 kW, S327.4 kWSpindle speed range - 20-3 500 n.min-1Reed range 1-5 000 mm.min-1Speed feed in X, Y axes - 15 m.min-1Speed feed in Z axes - 10 m.min-1Total length - 5 900 mmTotal width - 3 400 + 3 600 mmTotal height - 3 400 mm.
used
Contour edge banding & trimming machine Make: VITAP Type: SMART-3 New machine - With swivable trimming station - For straight and formed workpieces (convex and concave) - 1 glue spreading roller for 10-60 mm panel thickness - Guillotine to cut bands up to 3 mm thickness - edge 0,5-3mm 2 tape feeding speed (3 m/min or 7 m/min) -Glue pot 1kg capacity - Tape plate Ø=520mm Solid Phenolic table - Easy to clean - With no heat transmission - Electronic temperature control - Foot pedal command for the guillotine Tilting trimming unit - with 1 high frequency motor HP 0.75 (kw0,55) - 1 cutter Head with 2 knives r1mm/r2mm/r3mm - Support tape plate Ø 600 mm - Semi-automatic end-cutter with motor 0,5 kw and blade Ø=125 mm - Working table 400 x 300 mm. - CE standards. Optional available for an extra charge: - Cutter (without knives) - Set ...