We use cookies to optimize our website for you and to be able to continuously improve it. By continuing to browse the site you are agreeing to our use of cookies.
Disagree
Equipments: Size: B65xT70xH160 cm Power supply: 380 V wire sizes: round wire No. 30 to 21 Issue size: up to 25 mm Speed: max. 170 stitches/min Block-/Sattelheftung Weight: approx .: 250 kg stapling speed: up to 170 staples / min as is ...
AGG 600_SSK0 Achievement: PRP: 600.0 kVA / 480.0 kW / 866 A ESP: 660.0 kVA / 528.0 kW 50 Hz 400 volts Disposals: Terminal strip 3-pole, neutral conductor, grounding. Engine: Scania DC16 093A 02-54 Power: 545.0 kW Cylinders: 8 Cooling water capacity: 68.0 l Oil volume: 48.0 l incl. starter battery 24 volts Generator: Nidec TAL Series 600 kVA 1 Bearing Synchronous generator with AVR voltage regulation, directly with Steel disc clutch flanged to engine. Construction: NEA in soundproof hood with 990 l base frame tank. Control: Comap InteliLite AMF25 automatic emergency power incl. battery charger and cooling water heater, for automatic start in the event of a p ...
Agie Charmilles Form E 600 EDM Wire Cutting Machine C axis X, Y, Z axis: 600 x 400 x 400 mm Working table.: 800 x 600 mm Maximum workpiece weight:: 1000 Kg Machine is in like new condition ...
X-travel: 600mm, y-travel: 500mm, z-travel: 540mm, max. distance-table: 690mm, feed: 40m/min, table dimensions: 700x500mm, max. workpiece weight: 800kg, controls: Heidenhain TNC 620, connected load: 18kVA, length: 2240mm, width: 3338mm, height: 2803mm, weight: 5.6t, with documentation, has not run much.
Ref. -No.: 10339 Manufacturer: AGIE CHARMILLES Year of construction: 2008 Type of control: CNC Control: Heidenhain iTNC 530 (2P) Storage location: Halberstadt Country of origin: Schweiz serial number: 107.20.00.040 X-Travel: 650 mm Y-Travel: 600 mm Z-Travel: 500 mm Main spindle drive power: 30/39 kW Main spindle speed range: 20.000 RPM Table Dimensions (Lengthxwidth): 800 x 600 mm Table Load: 500 kg Max. Workpiece Weight: 6,5 kg Tool change time (chip-to-chip): 7 s Max. Tool Length: 300 mm Max. Tool Diameter: 130 mm Tool change time: 1,5 s Workpiece Diameter At Full Load: 80 mm Workpiece Diameter With 2 Vacant Positions: 130 mm T - groove width: 14 mm T - slot spacing: 63 mm Tool Taper: HSK- ...
x-travel: 650 mm y-travel: 650 mm z-travel: 550 mm Control: HEIDENHAIN iTNC 530 tool change unit: 60 pos. table diameter: 600 mm a-axis: +91/-120 ° c-axis: 360 ° number of spindle speeds: 20.000 U/min/rpm tool adaptor: HSK-A63 spindle drive: 39 kW Internal cooling system: 18 - 70 bar chip conveyor: kW total power requirement: kW weight of the machine ca.: t dimensions of the machine ca.: m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
EDM Drahterodiermaschine AGIE AGIECUT 250 with 15 PF THERE, generator and control. construction year: In 1992 state: Gebrauchtmaschine (in the very good state) technical data: Verfahrwege (X x Y x Z): 400 x 250 x 250 mms Max Werkstueckgroesse Werkstueckgroesse werkstueckgroesse X: 860 mms Max Werkstueckgroesse Werkstueckgroesse Werkstueckgroesse Y: 580 mms Max Werkstueckgroesse Werkstueckgroesse Werkstueckgroesse Z: 250 mms work piece weight: 400/800 kg. with automatic Drahteinfaedelung . record and without bain-marie possibly. Drahterodiermaschine Agiecut 250 dimensions: length 1920 mms x width 2,020 mms x height 2440 mms weight: approx. 3,000 kg DA15 PF di ...
lechrichter, used,      sheet leveller, used,  Type: UBR 10 x 2000 /1-16 Manufacturer / make: WMW Gotha max. sheet width: 2000 mm max. sheet thickness ( St 50): 10 mm   min. sheet thickness / min. sheethickness: 3 mm  Number of straightening rollers: 13 rollers / rollers Directionroller Diameter/diameter of    straihgtening rollers: 145 mm Directional speed / speed of straightening: 16 m / min Bale length / convexity length of rollers: 2330 mm Center distance of directional rollers/ distance b/n rollers ce ...
New laboratory extruder 25/25 LD Extruder Motor - AC Motor 2.2kW Water bath - 1000 mmm Granulator for a strand ...
AGIETRON HYPERSPARK 2 HS Sinker 2008 Design with lowerable working container Work table with 50 mm hole grid travel X/Y/Z 350x250x350 mm -Workpiece size: LxWxH=650x580x250 mm or 820x420x250 mm Integrated C axis, for rotation, indexing and erosion Electronic laser measurement of all axes Detection of the electrode and workpiece position 1 set of documentation (CD + manuals) AGIEVISION 5 Control with multitasking DNC interface with transmission protocolXon/Xoff and LSV2 2 serial interfaces RS 232C for DNC and master computer LAN connection for data exchange via in-house network RJ45 3 drives: hard drive, 3 1/2" floppy disks, CD-ROM Without tool changer