ersa used for sale

ERSA HOTFLOW - 7 Soldering furnace / tunnel dryer / belt dryer / continuous dryer Type: HOTFLOW – 7 Convection oven as soldering oven / tunnel dryer / belt dryer / continuous dryer for drying sheet materials on top and bottom. 4 heating zones at the top, 4 heating zones at the bottom, for drying on both sides. Rolling bars at a distance of approx. 4.5 cm on 2 transport chains as a support for plates Temperature range from 20° to 300°C Rated power Pn = 72 KW Nominal current In = 106 A Voltage: 3 x 400 / 230V Back-up fuse: 3 x 125 A Frequency 50 Hz Power: 67 KW Year of construction: 2000 Dimensions: Length: 5250 mm Width: 1300 mm Height: 1750 mm (incl. warning light) Height: 1450 mm (without warning light) Dry section: Length of heating zones: 3300 mm Transport width: 500 mm Exhaust pipes and additional fan can be supplied. Circuit diagrams are ...

ERSA HOTFLOW - 7 Tunnel Dryer / Belt Dryer / Continuous Dryer Type: HOTFLOW – 7 Convection oven as a tunnel dryer / belt dryer / continuous dryer for drying plate materials on the top and bottom. 4 heating zones at the top, 4 heating zones at the bottom, for drying on both sides. Rolling rods at a distance of approx. 4.5 cm on 2 transport chains as a support for plates Temperature range from 20° to 300°C Nominal power Pn = 72 KW Nominal current In = 106 A Voltage: 3 x 400 / 230V Back-up fuse: 3 x 125 A Frequency 50 Hz Power 67 KW Year of construction 2000 Dimensions: Length: 5250 mm Width: 1300 mm Height: 1750 mm (incl. warning light) Height: 1450 mm (Without warning light) Dry section: Length of heating zones: 3300 mm Transport width: 500 mm For possible use as a soldering oven – soldering machine – reflow oven, a cooling zone must be set up.  ...

Data sheet / Offer spare Monitor Deckel Controls Dialog 11 Dialog 12 Overview: - 12,1 industrial monitors TFT substitute with 14CRT monitors. - Connection: compatible plug connectors to the very easy installation. - Chassis monitor from high-quality high-grade steel case with compatible connection. Description: The monitor is conceived so he at few minutes of the operator independently after the enclosed instructions it can be exchanged. The control timing is preset i.e. the monitor is ready for use immediately. Micro-adjustments can be changed about the self explicatory menu ON SCREEN arbitrarily by customer wish.The connections for the graphics signal are by a Sub-D conector 25pol. he can not wrong are put on is able marked. The monitor TFT is fastened to the same points like the original monitor and this guarantees easy installation

Data sheet / Offer spare Monitor Heidenhain Controls TNC 131, 135, 145, 150, 151 Overview: - 8,4 industrial monitors TFT substitute with 14CRT monitors. - Connection: compatible plug connectors to the very easy installation. - Chassis monitor from high-quality high-grade steel case with compatible connection. Description: The monitor is conceived so he at few minutes of the operator independently after the enclosed instructions it can be exchanged. The control timing is preset i.e. the monitor is ready for use immediately. Micro-adjustments can be changed about the self explicatory menu ON SCREEN arbitrarily by customer wish.The connections for the graphics signal are by 24pol. Centronics conector he can not wrong are put on is able marked. The monitor TFT is fastened to the same points like the original monitor and this guarantees easy installation

Data sheet / Offer spare Monitor Heidenhain Controls TNC 155,355 Overview: - 12,1 industrial monitors TFT substitute with 14CRT monitors. - Connection: compatible plug connectors to the very easy installation. - Chassis monitor from high-quality high-grade steel case with compatible connection. Description: The monitor is conceived so he at few minutes of the operator independently after the enclosed instructions it can be exchanged. The control timing is preset i.e. the monitor is ready for use immediately. Micro-adjustments can be changed about the self explicatory menu ON SCREEN arbitrarily by customer wish.The connections for the graphics signal are by 15 pol. SUB-D conector he can not wrong are put on is able marked. The monitor TFT is fastened to the same points like the original monitor and this guarantees easy installation

We offer mostly new Tetra Pak spare parts -> We will send you our list on request - New Tetra Pak ® spare parts for TBA 8, TBA 3, A3 flex, PT 8, TBA 21, PT 21, TCBP 70, TCAP 21, 75 ... In the list -> Sent on request you will usually find new spare parts for Tetra Pak ® machines such as TBA 8 A3 flex PT 8 TBA 21 PT 21 TBA 19 (mainly volume flaps for TPA330SQ) TCBP 70 TCAP 47 (little) TCAP 21 (little) TCAP 75 (little) TBA 3 Tetra Pak Homogenizer ... Intermediate sale reserved

Connected load: 41kW, an inspection is possible.

Working width: 250mm, transport angle: 4-7°, transport speed: 0.3-2.5m/min, solder volume: 120kg, preheating length: 800mm, connected load: 8kW, length: 1980mm, width: 770mm, height: 1430mm, weight: 250kg, filled with lead-free solder, with documentation, on-site inspection is possible.

Used pliers gripper with segments A.S. and B.S - suitable for Heidelberg Era Speedmaster SM74 - for semi-automatic and fully automatic turn - Plier sgripper v.Bj.2017 - without damage and breakpoints - continuous run 100% accurate - Lagerboks have no game - Curve rollers and needle bearings v. segments kpl.renewed - 100% functional

Trackball with connection cable for Ultimax control Replacement for Hurco Ultimax 4 , Ultimax 3 Easy to change, ready to ship New

Spare parts for Nagema packaging machines PA1 / HM4 etc. Complete format sets for Nagema flow wrapping machines. Various stainless steel fittings ( 2 & 3 - waycock, arches, butterfly valves etc. )

Manufacturer: Schaltschrank Ersatz, Type: Inkl. aller Komponenten im Schrank,

Manufacturer: Ersatzrollen, Length mm: 505, roller diameter: 80, 1 Stückzahl : 495,

Manufacturer: Bürkle Ersatzlackwalze, Ersatzwalze für: Bürkle SLC, Bürkle: yes, Gummierte Länge cm: 1410 mm, shore Härte: 20-25, Stärke Gummierung ca. mm: 20, Gummierte Auftragswalze mm: 238,

Replacement base -Socket: IB ST ZF 24 DO 32/2 -Decentralized Interbus-S ORD. NO. - 2750170 without module electronics -Number: 41 pieces in stock -Price: 18 euros per piece

pneumatic piston pumps, airless high pressure pump, air motor AIR MOTOR -Spare part -Weight: 10 kg

Soldering station, soldering iron, chip soldering system, workshop soldering iron, hammer soldering iron -Power: 220 V 300 watts -Weight: 1 kg

Ersay Glass Filling Line Plastic lid Capacity : 22.000 bottles per hour Machine is in good condition

REXROTH: Pump combination SY3DFEE-2X / 140-140-71 Spare part number: 02004-0961 Manufacturer number: MNR: R901021899 + valve MNR: R900702586 MNR: R901021899 + valve MNR: R900702586 MNR: R910970517 Pump combination 3-way AKP140R / AKP140R / 71DR

REXROTH: Pump combination 140DFEE_140DFEE_71DR Spare part number: 02004-0972 Manufacturer number: MNR: R901021899 + valve MNR: R900702586 MNR: R901021899 + valve MNR: R900702586 MNR: R901021900 + valve MNR: R900702586 Pump combination 3-way AKP140R / AKP140R / 71DR

Demag Plastifiziereinheit SC Zylinder Ø50 zu Demag Ergotech - IU 1450 - Ø 50mm - Hubvolumen: 530 cm³ - Einspritzdruck: - Spritzteilgewicht - Schnecke: Einzug: 49,50mm Ausstoß: 49,30mm RSP: 49,93mm - Zylinder: Einzug: 50,00mm Ausstoß: 50,00mm - Voll funktionsfähig - Aus laufender Maschine ausgebaut

Ladies and gentlemen, we can offer you on request various aircraft spare parts new and used. With a friendly greeting Trade & Translations

We offer spare parts and accessories for hose pouring machines. Visit our homepage: www.protech-web.de

IPS: AOT-1; DI-1C; BA-1C; BA-2; MCU-5; CNT-2D; IBI-1; AIO-1; BA-3C; CNT-2; IBG-1; DO-1C; DIO-1C; DIO-3; PPS-BA1; IDS-2 measurement module Metronic Partly unopened original packaging and much more

Various spare parts for SOMOS dryers e.g.: gear wheels, electrical parts, desiccant Chambers, filter elements, blowers, heating elements, motros, sight glasses, turbines, magnetic valves or cylinders can be offered on demand.

Our product range includes not only new mixer 3-75,000 litre mixing volume, but also machine, which partially or completely be overhauled. In addition we offer transmissions, swing arms, Auger gladly at any time use and Generalüberholten different mixer types (including V-mix, NAUTA - and Vriecomischer) with a comprehensive range of services and spare parts available.

Multifunction - X-rays Built in 2002, in good condition

V-mix, Nautamix, Vrieco-, NAUTA mixer, cone mixer N.M. Holiness B.V.. spare parts Second-hand machine You are looking for replacement parts for your cone mixer? We have the most common spare parts for various products such as E.g. Nautamix, v mix, Vrieco-mixer etc. in stock, or they can customize quickly and cost-effectively in our workshop. -Mixing augers -Spare or replacement transmission -Spare or replacement swing arms - gears, shafts, seals -Top bearings -Universal joints -Radial storage -Outlets -Etc. In addition, we have a repair and maintenance service. We like to submit a non-binding offer. E-mail: t.roechter@heiligbv

Are you looking for spare parts for your cone mixer? We have the most common spare parts suitable for various brands such as Nautamix, V-Mix, Vrieco mixeretc. in stock, or can produce them quickly and cost-effectively in our workshop. - Mixed screws - Replacement or replacement gearbox - Replacement or replacement of swivel arms - Gears, shafts, seals - Top bearings - Cross joints - Radial bearing - Outlets - Usw. We also have a repair and maintenance service. We would be happy to make you a non-binding offer. E-mail: t.roechter@heiligbv

You are looking for replacement parts for your cone mixer? We have the most common spare parts for various products such as E.g. Nautamix, v mix, Vrieco-mixer etc. in stock, or they can customize quickly and cost-effectively in our workshop. -Mixing augers -Spare or replacement transmission -Spare or replacement swing arms - gears, shafts, seals -Top bearings -Universal joints -Radial storage -Outlets -Etc. In addition, we have a repair and maintenance service. We like to submit a non-binding offer. E-mail: t.roechter@heiligbv

Spare parts suitable for sacred V-mix, Nautamix, NAUTA -, Foeth mixer, Vrieco - cone mixer second-hand machine You are looking for replacement parts for your cone mixer? We have the most common spare parts for various products such as E.g. Nautamix, v mix, Vrieco-mixer etc. in stock, or they can customize quickly and cost-effectively in our workshop. -Mixing augers -Spare or replacement transmission -Spare or replacement swing arms - gears, shafts, seals -Top bearings -Universal joints -Radial storage -Outlets -Etc. In addition, we have a repair and maintenance service. We like to submit a non-binding offer. Email: t.roechter@heiligbv

Used - parts, etc. Front axle - rear axle - steering cylindrical - Lenkorbitrol - diesel engine - seat - fittings - steering column cover - hood - gears - lights - hydraulic - cutting spindles - steering wheel - cooler - fuel pump - tank - snake - switch -. Bonnet etc.

Different parts of the B & Z - sorting carriage are for sale.

Mesh belt for AUMA / Rotocure new and unused Length: 14100mm Width: 2250mm

HB QUICKMASTER 46-2 FOR SPARE PARTS M. No.: 964301 Format (cm): 34x46 Condition: Not in operation (central electronic board) // All other machine parts are in good working condition

Manufacturer: Bürkle, Type: Wellenträge Ersatzbürste, Year: ca.1998, FREETEXT1: Träger für Beizvertreiber Maschine, FREETEXT2: mit Schnellspan möglichkeit, Year :ca.1998

Manufacturer: Josting, Type: Ersatzmesser Fuznierschere, FREETEXT1: Messer länge 2950 mm, FREETEXT2: Rückenhöhe 80 mm, FREETEXT3: Bohrabstand mitte 15, FREETEXT4: Bohrabstand 110,

tool cabinet -with: spare parts for toolmaking, fixture construction -div. Drill bushings: different sizes -div. Clamping elements -Dimensions: 670/300/H2000 mm -Weight: 200 kg

Electric clutch, electromagnetic clutch for guillotine shears, tin snips, tin guillotine shears, crank guillotine shears, eccentric press -for: guillotine scissors crank guillotine scissors -Equipment: clutch, transformer, control -Manufacturer: LABOD electronic -Type: GN 6 DZ.4Q.80 -Total net weight: 160 kg

4-application chucks, wedge bar chucks, three-jaw chucks, three-jaw lathe chucks, power chucks, hydraulic chucks -Spare parts: for hydraulic power chucks different types -Chuck size: Ø 210 mm -Weight: 124.2 kg

Three-roll round, three-roll sheet metal bending machine, bending machine, sheet metal bending machine, 3-roll round bending machine, profile bending machine, three-roll sheet metal rolling machine -Spare part top roller -Drawing with the pictures -Max. Sheet width: 2060 mm -Max. Sheet thickness: mm -Roller diameter: 141 mm -Bearing diameter: 75 mm -Transport dimensions: 2690/141/H141 mm -Weight: 290 kg

Directional control valve, solenoid valve, hydraulic valve, pressure valve, valve block, control block -comes from a Krauss Maffei 1000 t injection molding machine -Machine type: KM 1000/5000A -Valve manufacturer: Bosch -Type: 081WV10P1N126WS024/00AO -Type: 0811 104 124 -Max. Pressure: 315 bar -Tension -Dimensions: 850/600/H550 mm -Weight: 634 kg

Cutting sieve, shredder sieve, sieve basket, sieve for chopper, shredder system, single-shaft shredder, shredder, granulator, shredding machine -Perforation: 65 x 65 mm -Recording holes: Ø 75/30 mm -with supporting ribs -Drawing with the pictures -Dimensions: 1600/1844/H620 mm -Weight: 696 kg

electric soldering iron, soldering device, for soldering machines ERSA Type 601 Power: 0.08 kW ( 80 watts ) Connection voltage: 24 V DC temperature: max. 350 °C approx. 0.35 m Connection cable Soldering tip: 52 mm ( 30 / 10 / 12 mm ), cone-shaped used, tested ! dimensions ( without cable ): 195 x 100 x 55 mm,

Ersatzwelle(Paddel), (drive shaft) for the STT 5000 + STT 2000. Mint condition, never used.

Ueberholungsjahr 2016 Baujahr 2010 Saegeblatt Hartmetall 500 mm Antriebsleistung Saegemotor 7,5 KW Drehzahl Saegemotor 2000-38000 min-1 Schnittgeschwindigkeit Saegeblatt 3100-6000 mm/min Saegeblattvorschub stufenlos Einstellbar 0-40 mm/ s Arbeitsbereich 90° max.:460 x 50 mm Nachschublaenge Pneumatisch: Einzelhub:max. 300 mm Servogesteuert: Einzelhub:max. 300 mm Mehrfachhub:max. 9999mm Nachschubgeschw. Servogesteuerte Nachschubeinheit 300 mm/s Druckluftanschluss bauseits 6 bar Gewicht(Saege)ca.: 1000 Kg Abmessungen LxBxH(Saege)ca.: 2100mm x2000mm x1600mm Hydraulikagregat) ca.: 900mm x600mm x800mm Technische Beschreibung Pressta Eisele Profilma 540 Retrofit Pressta Eisele Profilma 540 Retrofit Vollautomatischer Hochleistungs-Saegeautomat fuer NE-Metall und Kunstoffe Die Maschine befindet sich nach abgeschlossenem Retrofit sowohl technisch als auch op ...

Operator Panel, Terminal, PCD7.D850, SAIA, mint condition Manufacturer: SAIA Type: PCD7.D850 Attention! We have set the lowest price for the new part on the market. We still have several identical and other such devices, but the amount is ending. Buy more than 1 piece, there is still a great discount. Neuwertig in Originalverpackung! Der Teil wurde aus einem Ersatzteillager einer Firma gekauft und war noch nie im Betrieb, ist völlig neuwertig und in der Originalverpackung. Function guarantee! For second hand parts, we can not accept any conventional guarantee and warranty. Since we know that the device works, we give you a functional guarantee when you buy it. If the device does not work within 6 months after purchase you can return the goods and we will refund the purchase price.

oven 650 1.0x1.0x5m bogie 6 zones PLC data monitoring Öfen für die Wärmebehandlung Metalle einfache Härtesysteme Härterei-Zubehör gienanth Glühöfen Umluftöfen zum Glühen, Anlassen Salzbadöfen Schutzgasöfen Nitrieröfen und Plasmanitrieröfen Mehrzweckkammer-ofenanlagen kontinuierliche Ofenanlagen Vakuumprozesse Vakuumhärten Vakuumglühen, -anlassen, Nitrieren Vakuumlöten Metal Injection Moulding Induktionserwärmung Öfen für die Kunststofftechnik zum Trocken, Tempern, Polymerisieren, Einbrennen usw.; Ausführung als Kammeröfen, Haubenöfen, Herdwagenöfen, Schachtöfen; Herdwagen-Schmiedeöfen Umluftöfen Kammerofenlinien Nitrieröfen Plasmanitrieröfen Vakuumprozesse Schmelzöfen Trocknen Tempern Laboröfen Ersatzteile Öfen Kammeröfen Herd wagenöfen schoenheider Herdwagenöfen zirlguss Glühen Härten Tempern Umformen Vorwärmen Schmieden Thermi ...

Fugenreiigungsmaschine for stone floors Working width 50 cm Powered electric 2.2 kW L x W x H: 120 x 60 x 80 cm Weight 130 kg Built approx. 2001 The machine is little used, in good condition, ready to use. Subject to changes, errors, prior sale! Service/Ersatzteile durch MATEC CH-4900 Langenthal/DE-79618 Rheinfelden MATEC system+technik GmbH Maschinenbau Eisenbahnstrasse 25 CH-4900 Langenthal/Switzerland Tel. 0041 62 966 18 32 Fax 0041 62 966 21 12