We use cookies to optimize our website for you and to be able to continuously improve it. By continuing to browse the site you are agreeing to our use of cookies.
Disagree
Search Dornier Delta or Dornier Delta II Lithotripter / lithotripsy ...
Non-contact position measuring system Manufacturer: Dornier Type: I-W-A Anwendungsgebite are: Axial and radial shaft vibration measurements Monitoring of measuring tolerances Determination of deformation and displacement Measurement of wave and eccentricities Roundness measurement Valve position measurement Thickness measurement Accessories: various transducer and mounting plates Evaluation electronics Connection cable Operating instructions Calibration curves Condition: used More info: see also photos All information without guarantee
Dornier Opus with the following device components: generator Hofmann Selector D tube Comet DI 97 HS-33/81-150 0.6/1.2 Image amplifier 40cm complete and in good technical and cosmetic condition • The system was tested before dismantling of our employees on site. • It is located in our warehouse in Germany, packaged on pallets properly lashed down and wrapped in stretchfoil and can be picked up immediately. • You buy the equipments in "as in" condition from stock Freiberg (EXW), Saxony, Germany, and prepayment. • We are a used medical device dealer. We do not service or refurbish any of the items that we sell. All items are sold used and in as-is condition, unless otherwi ...
Very good device from 2005/2006 Relax Plus treatment table ...
Working width: 4000mm, with 3 warp beams, 6 sectional warp beams, 20 shafts 13 inch, dobby machine 2881/2 and batch winder Neuenhauser, operational hours counter: 10,613h. ...
Capacity: 40-60 t/h working width: 800 mm Last picture is only demo! ...
Qty. 1 Second-hand wire cage welding machine – very good condition Mfc.: Züblin Type: ASMS 30 200 Built: 1985 Machine for production of wire cages within the range of diameters between 300-2250 mm. Wire cage dia.: 300 – 2250 mm Dia. of longitudinal wire: 5 – 7 mm Number of longitudinal wires: 12 Diameter of ring wire: 5 – 9 mm Grade of ring wires: 35 – 165 mm Longitudinal wire – speed:0.3-3.0 m/min.
sheet width: 3100 mm plate thickness: 6 mm pre-bending: 5 mm upper roll diameter: 200 mm min. bending diameter: Ø 300 mm bending speed: 5 m/min total power requirement: 5,5 kW weight of the machine ca.: 4.000 kg dimensions of the machine ca.: 4800x1300x1270 mm The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
sheet width: 2050 mm plate thickness: 4,5 mm pre-bending: 4,0 mm min. dia.: 210 mm roll diameter: 140 mm weight of the machine ca.: 1530 kg dimensions of the machine ca.: 3220x1200x900 mm Standard features: - Central rollers via electric motor, planetary reduction gear and Gear drive driven - Swivel top roller - Main engine with brake device - Conical bending device - Mobile controller and foot pedal - CE mark / Declaration of Conformity Additional equipment: - motorized rear roller adjustment - Digital display for back roller - induction hardened rolls The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
sheet width: 1250 mm plate thickness: 5,5 mm pre-bending: 5,0 mm roll length: 1280 mm min. dia.: 210 mm roll diam. toproll: 140 mm weight: 1365 kg range L-W-H: 2.020 x 900 x 1.200 mm Standard features: - Central rollers via electric motor, planetary reduction gear and Gear drive driven - Swivel top roller - Main engine with brake device - Conical bending device - Mobile controller and foot pedal - CE mark / Declaration of Conformity Additional equipment: - motorized rear roller adjustment - Digital display for back roller - induction hardened rolls The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.