We use cookies to optimize our website for you and to be able to continuously improve it. By continuing to browse the site you are agreeing to our use of cookies.
Disagree
Clamping force: 100 t Year of construction: 2001 Injection weight in PS: 149 g Control Type: NC4 Injection unit: .../310 Screw diameter: 35 mm Spec. Injection pressure: 2020 bar Spray volume: 168.3 cc Injection weight in PS: 149 g Hydr. Drive power: 18.5 kW Cylinder heating capacity: 9.4 kW L/D screw ratio: 20 Clamping unit: 100/... Clamping force:: 100 t Size of clamping plates: 600 x 600 mm Lights spar spacing: 420 x 420 mm Ejector force: 41.2 kN Tool installation height: 250 mm Aperture travel: 500 mm Max. plate spacing: 750 mm Ejector travel: 150 mm General information: Fuel tank capacity OIL: 220 l Weight: 4800 kg Dimensions(m) LxWxH: 4.3 x 1.4 x 2.0 m Equipme ...
Molding machine of Mag Type: Ergotech 420/800-3300 system control: NC 4 year: 2000 Clamping unit Clamping force t 420 gap mm: 710 Holm dimension mm: 810 x 710 min/max height mm: 820 / 940 Plate size: 1200 x 1100 injection unit Screw diameter mm: Gr 80 injection weight: 1600 Injection volume cm 3: 1779 spray pressure bar: 1855 Dimensions and weights Dimensions Lxwxh m: 7.8 x 2.2 x 2.4 machine weight kg: 21000 Miscellaneous 4 core EUROMAP 12
Screw diameter: 35mm, operating hours: 73,500h, on-site inspection is possible. ...
Demag Ergotech System 80/420-430 Year of construction: 2006 Injection unit: Screw diameter: 40 mm Injection weight: 205 g Injection pressure: 2020 bar Dosing volume: 231 ccm Clamping unit: Clamping force: 80 t Tie bar spacing: 420x420 mm Size of clamping plates: 580x590 mm Ejector: hydraulic Clamping unit: hydraulic Control: NC4 Additional equipment: Euromap 67 Robot Interface Air valve x 2 Hydraulic Core Pull x 3 Control with hot runners Injection unit hardened - Bimetal Built-in printer It is possible to change the screw diameter Metrics: Weight: 4100 kg Length/Width/Height: 4.10x1.40x1.90 m All offered machines are started by our service technicians b ...
Clamping force: 420t, screw diameter: 70/ 15mm, injection volume: 1212/ 292cm³, length: 7900mm, width: 2200mm, height: 5000mm, weight: 25t, with robot. ...
Demag Ergotech Compact 800/420-200 Year of construction: 2000 Injection unit: Screw diameter: 30 mm Spray weight: 94 g Injection pressure: 1990 bar Dosing volume: 106 ccm Clamping unit: Clamping force: 80 t Tie bar spacing: 400x400 mm Size of clamping plates: 580x590 mm Ejector: hydraulic Clamping unit: hydraulic Control: NC4 Additional equipment: Machine in very good technical condition Euromap 12 Robot Interface Air valve x 1 Hydraulic core pull x 1 Injection unit hardened - Bimetal Machine was not in use in an ongoing production. This was only used to test the tools It is possible to change the screw diameter Metrics: Weight: 4000 kg Length/Width/Height: ...
Molding machine of Mag Type: Ergotech 100-430 system control: NC 4 year of construction: 1999 Clamping unit Clamping force t 100 gap mm: 500 Holm dimension mm: 400 x 400 min/max height mm: 250 / 750 Plate size: 590 x 590 injection unit Screw diameter mm: Gr 40 injection weight: 205 Injection volume cm 3: 231 spray pressure bar: 2020 Dimensions and weights Dimensions Lxwxh m: 4.4 x 1.4 x 1.8 machine weight kg: 4400 Miscellaneous EUROMAP pull 12, 1 core
Operational pressure: 210bar, weight: 4t, with documentation, without accessories. ...
Molding machine of Mag Type: Ergotech 250-1450 system control: NC 4 year of construction: 1996 Clamping unit Clamping force t Gap between 250 mm: 575 Holm dimension mm: 560 x 560 min/max height mm: 660 / 760 Plate size: 830 x 830 injection unit Screw diameter mm: Gr 70 injection weight: 940 Injection volume cm 3: 1039 spray pressure bar: 1400 Dimensions and weights Dimensions Lxwxh m: 5.7 x 1.7 x 2.2 machine weight kg: 11200 Miscellaneous 2 core EUROMAP 12
There are two Injection Moulding Machines Demag Ergotech System 250/630-1450 available, clamping force 250t, clear tie bar width: 630mm, operating pressure: 190bar, weight: 13.1t, year of construction machine 1/ 2: 2001/ 2006, with documentation, an inspection is possible. ...