Year of construction 1989, front payload 4520 kg, rear payload 14960 kg, total weight 19480 kg, permissible up to 30 km/h, see appendix for data ...

• more information

- Exhibition device - ; new exhibition machine ...

• more information

Collman Buffing / Building / Peeling Machine Ref: RB007 Year 1980’s 50 volts 50 cycles 20kw Manual peeling, buffing, building Good for PCR truck and Light OTR tyres Latest standards  ...

• more information

Collman Building Machine Ref: RB008 Quick building due to double rollers Manual With full rack of plates  ...

• more information

Collman Building Machine Ref: RB003 For tyres up to 2.5m and 1m wide With hydraulic cutting unit Can use for smooth and groove Buffing arm can be supplied but will need to be rebuilt with spare motor before being able to use as a Buffer Fully operational Peel, Buff (with arm), Build, Cut Hydraulic motor you can use to cut through cured tyres (very strong arm) Modern Panel

Lawn building machine Sembdner RS 60 R, working width 60 cm, drive F&S 2-stroke petrol engine. Reversing gearbox for forward and reverse travel. Equipment: smooth roller with scrapers at the front, hedgehog with cleaning cage in the middle, smooth roller with scrapers (water-fillable) at the rear, seed container with brush shaft and dosing slide. Technically good condition, but with flash rust and engine without ignition sparks - does not start. Branded product from Munich (Germany). Shipping optionally possible.

sheet width: siehe TD mm plate thickness: siehe TD mm pre-bending: 8mm total power requirement: 15 kW weight of the machine ca.: 9,7 t dimensions of the machine ca.: 5310 x 1660 x 1590 mm m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.  ...

• more information

sheet width: 3000 mm plate thickness: 10 mm distance between columns: mm total power requirement: kW weight of the machine ca.: 9,8 t dimensions of the machine ca.: 4,15 x 3,55 x 2 m Brand: Durma Type: DHGM 3010 Year of make: 2002 Knife length: 3.000 mm Plate thickness: 10 mm Electric backstop Machine dimensions (lxwxh): 4.150 x 3.550 x 2.000 mm Machine weight: 9.800 kg The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

offer 21001 Specifications: - working width 3050 mm - cutting capacity St 40 10 mm - Cutting angle 2 ° - Cutting gap adjustment by manual hand - Number of hydraulic hold-downs 17 pcs - Motor - Backgauge 20 - 1000 mm - front angle stop + support arms - Hydraulic drive 400 V / 22 kW - Table height approx. 900 mm - Space requirements incl. backgauge, without front support arms -ca. W 3900 x H 1950 x D 2250 mm - Weight approx. 7800 kg - with: - E-foot switch - Cutting line illumination - - Cutting length preselection

sheet width: 3100 mm plate thickness: 10,0 mm thickness at Niro-steel: 6,0 mm distance between columns: 3120 mm down holder: 16 Stück oil volume: 200 ltr. cutting angle: 1°50 no. of strokes: 13 Hub/min control: ENC 100M table width: 580 mm throat: 50,0 mm total power requirement: 22,0 KW weight: 9300 kg range L-W-H: 4200 x 2250 x 2100 mm from a maintenance workshop New price ~ 55.000 euros -------------------------------------------------- robust electro-hydraulic oscillating shears with DURMA ENC 100M NC control Manual cutting gap adjustment, via eccentric -------------------------------------------------- Furnishing: - electro-hydraulic oscillating shears - with DURMA ENC 100M contr ...