We use cookies to optimize our website for you and to be able to continuously improve it. By continuing to browse the site you are agreeing to our use of cookies.
Disagree
used
Clamping angle, T-slot plate, clamping table, clamping cube, clamping plate, clamping tower, clamping box -Table comes from an injection molding machine -Make: Arburg -Type: Allrounder 320-210-750 KN -Dimensions table: Ø 320 mm -Bore center: Ø mm -Dimensions: 320/320/H163 mm -Weight: 20 kg
used
ARBURG ALLROUNDER Arburg Allrounder 720 S 3200-1300 - Plastic Injection Machine screw size:70 mm injection shot weight in Polysterol:984 g/PS closing pressure:3500 kN core drawing:2 control:Selogica daylight:720 x 720 mm opening stroke:700 mm mould height - Max./min.:300 -700 mm daylight between platens - max.:1000-1400 mm weight of the machine ca.:17,7 t - highly wear-resistant plastification unit - Technology step 3 - hydraulic plant with 3 regulating pumps - Technology step 2 - servo-controlled / two-circuit pump technology - Increased power for heating control circuits 1-6 to 3.6 kW each - clamping force increased to 350 Mp - mould blow unit 1 with pressure reducer - mould blow unit 2 with pressure reducer - Core pull 1 - Core pull 2 - Interface for robot system according to EUROMAP 12 - Host computer interface for ALS with communication node Ethernet
used
Injection molding machine Manufacturer: Arburg Type: 320 S 50-60 Year of construction: 1997 Screw: 18 mm Clamping force max.: 500 kN Max. opening distance: 350 mm Tool installation height min.: 225 mm Tool clamping plates (WxH): 498 x 498 mm Weight bew. Half weight max.: 400 kg Effective screw length L/D: 24 Worm travel max.: 110 mm Moulded part weight max. g/PS: 45 Spray pressure max.: 2500 bar Worm torque max.: 325 Nm Screw circumferential speed max.: 54 m/min. Capacity granule container: 50 litres Horizontal injection position max.: 120 mm As an accessory, a removal is included. A screw with a diameter of 18 mm is mounted in the machine. The machine is fully functional and has always been maintained by Arburg.
used
This Arburg Allrounder 320 KS 700-100 Injection moulding machine was manufactured in the year 2001 in Germany and has 3467 production hours. It is equipped with an Arburg Selogica control unit.
used
Manufacturer: Arburg Type: 320 C 600 - 250 Year of construction: 2003 Control: Selogica Closing type: Hydraulic Closing force: 600 kN Tie bar spacing: 320 mm x 320 mm Plate size: 446 mm x 446 mm Tool height: min 200 mm Opening distance: 350 mm Plate spacing max.: 550 mm Screw: 35 mm Stroke volume: 106 ccm / 89 gram PS Injection pressure: 2470 bar general Engine: 15 kW Heating: 5.5 kW Dimensions: 3.4 m x 1.5 m x 1.6 m Weight: 2080 kg Screen text: German Optional extras Core train x1 Robot interface Sorting flap Hot channel integrated
used
Manufacturer: Arburg Type: 320 C 500 - 170 Year of construction: 11/2006 Control: Selogica Closing type: Hydraulic Closing force: 500 kN Tie bar spacing: 320 mm x 320 mm Plate size: 446 mm x 446 mm Tool height: min 200 mm Opening distance: 350 mm Plate spacing max.: 550 mm Screw: 35 mm Lifting volume: 115 ccm / 105 gram PS Injection pressure: 1470 bar general Engine: 11 kW Heating: 9.4 kW Dimensions: 3.4 m x 1.4 m x 1.9 m Weight: 2430 kg Screen text: German Additional equipment Core train x1
used
Manufacturer: Arburg Type: 320 KS 700 - 250 Year of construction: 2001 Control: Selogica Locking type: Knee lever Closing force: 700 kN Tie bar spacing: 320 mm x 320 mm Plate size: 476 mm x 476 mm Tool height: min 200 mm max 400 mm Opening distance: 250 mm Plate spacing max.: 650 mm Screw: 35 mm Stroke volume: 144 ccm / 121 gram PS Injection pressure: 1820 bar general Engine: 15 kW Heating: 6.1 kW Dimensions: 3.3 m 1.45 m x 1.6 m Weight: 2190 kg Screen text: German Optional extras Robot interface funnel
used
Manufacturer: Arburg Type: 320 C 500 - 150 Year of production: 2000 Control: Selogica Closing type: Hydraulic Closing force: 500 kN Tie bar spacing: 320 mm x 320 mm Plate size: 498 mm x 498 mm Tool height: min 225 mm Opening distance: 350 mm Plate spacing max.: 575 mm Screw: 35 mm Stroke volume: 106 ccm / 89 gram PS Injection pressure: 1610 bar General Motor: 15 kW Heating: 4,8 kW Dimensions: 3.4 m x 1.4 m x 1.7 m Weight: 2250 kg Screen text: German Additional equipment: Machine with handling Multilift Robotinterface Core pull hydraulic: x1 Air valve: Yes Tool heater x 6 Conveyor
used
Manufacturer: Arburg Type: 320 C 500 - 250 Year of production: 2002 Control: Selogica Closing type: Hydraulic Closing force: 500 kN Tie bar spacing: 320 mm x 320 mm Plate size: 446 mm x 446 mm Tool height: min 200 mm Opening distance: 350 mm Max distance between plates: 550 mm Screw: 35 mm Stroke volume: 144 ccm / 132 gram PS Injection pressure: 1820 bar General Motor: 15 kW Heating: 6,5 kW Dimensions: 3,4 m x 1,4 m x 1,7 m Weight: 2830 kg Screen text: German Additional equipment Robot interface Core pull hydraulic: x1
used
Arburg 320 S 500-150 selogica injection molding machine with a robot Year of production: 1999 Control: Selogica TECHNICAL DATA ⢠Closing force: 500 kN ⢠Clearance between columns: 320 mm x 320 mm ⢠Min form height 225 mm ⢠Max mold height 350 mm ⢠Board dimensions: 446 mm x 446 mm ⢠Opening distance: 425 mm ⢠Max distance. between plates 525 mm ⢠Snail: 30 mm ⢠Shot weight: 65 grams PS ⢠Injection pressure: 2210 bar GENERAL ⢠Engine: 15 kW ⢠Total installed power: 21.3 kW ⢠Dimensions: 3.2 x 1 x 1.8 ⢠Weight: 2250 kg ⢠German language control hours worked 45 970 h number of cycles 8 110 434 pcs Injection molding machine in production all the time As additional equipment, the injection molding machine has an original side manipulator for receiving ingots Regularly serviced, very good conditi ...
used
Arburg 320 C 500-270 injection moulding machine Year of production: 2007 Control type: Selogica Clamping System: Hydraulic TECHNICAL DATA Closing force: 500 kN Clearance between columns: 320 mm x 320 mm Plate dimensions: 446 mm x 446 mm Mould size: min. 200 mm Maximum opening distance: 350 mm Max distance between plates: 550 mm Screw diameter: 35 mm Injection Volume / Injection Weight: 115 ccm / 105 gram PS Injection pressure: 1470 bar GENERAL DATA Motor: 11KW Heaters: 9.5 kW Dimensions L x W x H: 3.9 m x 1.4 m x 1.9 m Weight: 2400 kg
used
ARBURG 70T 320 KS 700 - 100 INJECTION UNIT Screw diameter: 25 mm Calculated injection volume: 49 cm³ Length / diameter ratio: 20 L / D Maximum injection rate: 88 cm³ / s Pressure on the material: 2240 bars PS plasticization capacity: 41 Kg / h Screw Speed: 37 RPM CLOSING UNIT Closing force: 700 kN Opening stroke: 250 mm Mold thickness Mini / Max: 200/400 mm Max distance between tray: 650 mm Passage between columns: 320 x 320 mm Tray size: 476 x 476 mm GENERAL Heat output: 11 kW Total installed power: 17.9 kW Quantity of oil: 120 l. Weight: 2090 Kg
used
Arburg 320 C 500-270 Closing unit Clearance between columns (hxv) [mm] 320 x 320 Min./max. mold height [mm] min 200 Maximum opening width [mm] 550 Injection unit Screw diameter [mm] 35 Injection volume [cm3] 115 Injection weight [g] 105 Injection pressure [bar] 1470 Electrical and hydraulic equipment Rated power of the pump motor [kW] 11 Heater power [kW] 9.5 Dimensions and weight Net weight with control cabinet [t] 2.4 Dimensions (L x W x H) [m] 3.9 x 1.4 x 1.9 Closing unit Clamping force [kN] 500 Dimensions of mounting plates (hxv) [mm] 446 x 446
used
1998 Arburg Allrounder 320 M 500 - 210, 50 t Clamping force 50 t Screw 30 mm Mold height min 250 mm Distance between tie bars 320 mm Mould weight max 0,6 t Shot capacity 101 ccm Control Multronica Core pullers - no Hotrunner zones - no Weight 2610 kg, L x W: 4100 mm x 1200 mm year of made 1998 accessories - no (in price of machine is not hopper loader on photo, but is possible to buy it)
used
1996 Arburg Allrounder 320 M 500 - 90, 50 t Clamping force 50 t Screw 30 mm Mold height min 250 mm Distance between tie bars 320 mm Mould weight max 0,6 t Shot capacity 71 cmm Control Multronica Core pullers - no Hotrunner zones - no Weight 2360 kg, L x W: 4100 mm x 1200 mm year of made 1996 stock number 00660 accessories - no (in price of machine is not hopper loader on photo, but is possible to buy it)
used
This ARBURG 320 S 350-150 Injection moulding machine was manufactured in 2001 in Germany. It has a clamping force of 350 kN and a screw diameter of 30 mm. The min. mold installation height is 172 mm and the platen size is 472 x 472 mm. In total it operated 73384 pump hours. See original tech specs sheet (DE) as PDF attached below.
used
This ARBURG 320 C 500-100 + Multilift H with B-Axis Injection moulding machine was manufactured in 2003 in Germany. It has a clamping force of 500 kN and a screw diameter of 30 mm. The distance between platens is 550 mm and the opening stroke is 350 mm. In total it operated 64000 pump hours. The injection moulding machine comes with a Multilift H with B-Axis, featuring a handling weight gripper plus part weight of max. 5 kg and a swivel range B-axis of 90 degrees. See original tech specs (DE) attached as PDF below.
used
Manufacturer/Manufacturer: Arburg Typ/Type: 320S 500-350 Bau-year year: 1998 Control/Controller: Selogica Clothing Power/Clamping Force: 500 kN Schliessart/Clamping Type: Hydraulisch/Hydraulic Holmabstand/Dist.Betw.Tiebars: 320 mm x 320 mm Plate Groesse/Platen Size: 446 mm x 446 mm WZ Einbauhoehe/Mould hight: min 225 mm Oeffning weg/opening stroke: 350 mm Plate distance max/Max. Open Daylight: 575 mm Snail/Screw size: 40 mm Lifting volume/shot volume: 182 cm/153 gram hp Spez. Spray./injection pressure: 2050 bar General General Motor/Motor Power: 18.5 kW Heating/heating power: 6.3 kW Dimensions: 3.7 m x 1.2 m x 2.1 m Weicht/Weight: 2600 kg Screen text/Language: Deutsch/German Additional equipment/Additional equipment Euromap Rdzenie x1
used
Machine comes with robot Power : 50 Ton Distance between columns: 320x320 Screw diameter: 30 Calculated injection volume: 70 Min / Max mold thickness: 200 Euromap: 500-100 Moving platen stroke: 350 Working hours: 78.000
used
Closing force: 500kN, heating output: 4.9kW, connected load: 19.9kW, operational hours counter: 57,024h, with handling and conveyor belts, without dosing device.
used
Screw diameter: 30mm, max. opening path: 350mm, tool clamping plate dimensions: 446x446mm, weight: 2.25t, operational hours counter: 81.353h, with machine hopper, hydraulic core pull, air valve DS, pneumatic valve gate and documentation.
used
Heating output: 5.5kW, connected load: 16.5kW, weight: 2.61t.
used
Connected load: 40kVA.
used
Clamping force: 85t, heating output: 5.56kW, connected load: 24.1kW, weight: 2.4t.
used
Screw diameter: 35mm, clamping force: 50t, including Handling Walldorf, documentation and software.