found in all categories
Weight approx.: 5 kg Dimensions (l x w x h) approx.: 500 x 500 x 1220 mm Description: With pipes for painting aspiration
Weight approx.: 5 kg Dimensions (l x w x h) approx.: 500 x 500x 500 mm Description: Used painting pump
Weight approx.: 5 kg Dimensions (l x w x h) approx.: 500 x 500x 500 mm Description: Used painting pump
Table surface: 600x300mm, max. grinding length: 610mm, max. grinding width: 400mm, max. table spindle distance: 620mm, connected load: 3.7kW, length: 2700mm, width: 1490mm, height: 1800mm, weight: 2.2t.
Weight approx.: 1450 kg Dimensions (l x w x h) approx.: 2300 x 800 x 1500 mm Description: Center Lathe with - Forkardt 3-jaw chuck F250 with reversible jaws - 4-fold steel holder - 2 pcs. Lynetten - Coolant system - Emergency stop switch Turning diameter over bed 400 mm Turning diameter over support 245 mm Turning length 1100 mm Spindle bore 46 mm Speed 12 - 1600 rpm Tailstock sleeve mount MK 4 MK Total power requirement 4 kW Machine weight approx. 1.45 t Space required approx. 2.3 x 0.8 x 1.5 m
Fe-separator, parent band magnet, permanent magnet with new rubber strap, drive, drive and idler pulleys. Overall dimensions with gear Lxwxh: 2125 x 1500 x 690 mm Rubber belt width: 1000 mm new Magnetic core dimensions Lxwxh: 1100 x 950 mm Transmission: North Power: 2.2 KW Check machine, ready to use Strong magnetic
Weight approx.: 1500 kg Dimensions (l x w x h) approx.: 3500 x 1100 x 1600 mm Description: max. capacity 3000 kg, fork length approx. 2200 mm, fork arm distance outside 1100 mm, with battery charger
-Non-ferrous metal separators with magnetic drum and control. Suitable for material from 5 mm to 20 mm. Belt speed: adjustable from 0.5 to 2 m/s Weight CA. 1035 kg Power supply: 400V/50 Hz Working width: 600 mm Rotor: 20 pin Rotor rpm: 3000 rpm. Engine power rotor: 4 kW Power: 1.5 kW Control Panel complete with r & d Original operating instructions Machine: ready to use and functional
-Non-ferrous metal separators with magnetic drum and control. Suitable for material from 10 mm. Belt speed: adjustable from 0.5 to 2 m/s Weight CA. 1035 kg Power supply: 400V/50 Hz Working width: 600 mm Rotor: 10 pin, Rotor rpm: 3000 rpm. Engine power rotor: 4 kW Power: 1.5 kW Control Panel complete with r & d Original operating instructions Machine: ready to use and functional
turning diameter over bed: 400 mm turning diameter over slide rest: 245 mm turning length: 1100 mm spindle bore: 46 mm turning speeds: 12 - 1600 U/min tailstock quill taper MT: 4 MK total power requirement: 4 kW weight of the machine ca.: 1,45 t dimensions of the machine ca.: 2,3 x 0,8 x 1,5 m Center lathe with - 3-jaw chuck 250mm - 4x steel holder - Rotating tailstock center The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
-Non-ferrous metal separators with magnetic drum and control. Suitable for material from 20 mm. Belt speed: adjustable from 0.5 to 2 m/s Weight CA. 1035 kg Power supply: 400V/50 Hz Working width: 600 mm Rotor: 6 pin Rotor rpm: 3000 rpm. Engine power rotor: 4 kW Power: 1.5 kW Control Panel complete with r & d Original operating instructions Machine: ready to use and functional
Weight approx.: 2500 kg Dimensions (l x w x h) approx.: 1800 x 900 x 1800 mm Description: Capacity 1250 kg, max lifting height 2100 mm, fork length 900 mm, with 1 extra battery, see photos
Type of machine: Center lathe. Manufacturer: WAGNER. Model: DCS 160. Year of construction: 1979. Condition: good,. Type of offer: used machine, ,. Technical data:. Tip height: 172/255 mm, Top width: 800 mm, Spindle bore: 40 mm, Spindle speed: 30-1400 rpm,. Drive: 4.8/5.2/5.3 kW. Weight: 1200 kg. ,. The machine is in a good shape and ready for operation. It can be visited and demonstrated at our location.,. ,. We will be pleased if you take an interest in our offer.,.
Machine type: external thread cutting machine. Manufacturer: Wagner. Model: VOWA Minimatic. Condition: very good,. Type of offer: unused machine, ,. Technical data:. Facilities: with 2 cutting heads,. for threads: from 1/4 "to 1 1/2". Drive: 230 V, Accessories: with 2 liters of cutting oil,. ,. The machine is in a very good shape and ready for operation. It can be visited and demonstrated at our location.,. ,. We would be pleased if our offer takes your interest.,.
Year of construction: approx. 1965 maximum Rohrdurchm.: 40 mm Total power: 2 KW / 380 V Weight: 800 kg Equipment / Accessories: Thread-tapping head Wagner Coolant system Machine lamp Clamping JAWS for diameter. 16 / 20 / 25 / 32 / 40 mm All technical specifications have been created according to our best knowledge and existing documents; Expressly reserved by mistake. Any interested party can advance test the machine under power. One ord. Rchng. plus ges. VAT will be issued.
powder spray booth composed of: - booth LxWxH: 6200 x 2300 x 3250 mm - passage WxH: 800 x 1600 mm - 2x fire-extinguishing system - 2x cleaner + filter - 2x lift frame with 4 pistols - 2x Zyklon - 8x powder cart - electric cabinet
- Powder booth: PBS VarioColor - space powder booth B/T/H: 11 x 4 x 7 m - powder guns: 3 automatic mast - manual spray guns: 2 pieces - mast: 2 pcs. with size detection - workpiece size W x D x H: 1000 x (X) x 2500 mm - Cyclone: PBS B/T/H 7/2/2 m - cyclone : with recovery - fire-fighting system: STS - final filter: level under powder booth - space final filter W/D/H: 11 x 8 x 2.5 m Details: cabine, cyclone, powder centre, recovery, final filter (manufacturer PBS), application consisting of 6 automatic pistols and 2 hand pistols (manufacturer Wagner), fire-fighting system (manufacturer STS)
electrically operated air-less device -complete with cars, high pressure hose and gun
Weight approx.: 20 kg Dimensions (l x w x h) approx.: 450 x 300 x 600 mm Description: drive electric, 400 W, output 1.2 l/min., max. spray pressure 250 atmospheric excess pressure, 220 V, 50 Hz, 10 A
Radial drill Wagner PRC 60 Manufacturer: Wagner Year of construction: 1991 Weight: 7 t type: PRC 60 Cube table (L x W x H): 800 mm x 630 mm x 500 Spindle taper: MK5 Spindle stroke: 400 mm Throat depth min - max: 450 mm - 2000 mm Column diameter: 450 mm Senkrechtverst. Boom: 800 mm Hubgeschw. Boom: 1.02 m / min Number of speeds: 16 / 20-1600 Drilling depth adjustment scale: 151 mm Spindle drive: 5.5 kW Jacks: 2,2 kW Pillar clamp: 0.75 kW Machine dimensions (L x W x H): 3000 mm x 1250 mm x 3300 mm COMPLETE ENGINE PACKAGE CONSISTING OF: 1 band saw Amada HD 800 2. mechanical grinder Lima 400 L 3 Sadowski press brake HAP 200 x 3600KN 4. Darley table shears GS 3100 x 18 ...
Saw blade grinding machine, tool grinding machine, grinding machine, sharpening machine for circular saw blades -Sharness Automat for Cold Circular Saw Blades, -Saw blade sharpening machine with partial transmission -for grinding circular saw blades up to Ø 1200 mm -Automatic delivery and switching off -Dimensions 1250/1020 / H2250 mm -Weight 694 kg
Ratio of 28:1 Flow rate 14 cm3 Stroke rate max. 85 dH/min. Flow rate max 2,6 litres / min. Air inlet pressure of Max 8 bar Air consumption at 6 bar per IE 3 liter Max Ã?brdruck 224 bar Weight approx. 10 kg Width 430 mm, height 620 mm
Cycle lathe Wagner Model/type: W DE 400 x 1500 WRaumbedarf: 3000 x 1500 x 1600 mm Manufacturer: Wagner Year of construction: 2005 Power requirements (kW): spindle motor: 5,5KW control: Siemens 802 C. Machine weight (kg): 1550 ï?· Year: 2005 ï?· Control: Siemens 802C. ï?· Machine no 3 JAWS now has a new 4 jaw Chuck ï?· Workspace: o circulation specified = 400mm o circular Ã? over bed = 440mm o run around Ã? over cross slide = 210 mm o feed MK = 200mm o ï?· top wide = 1500mm â?¢ Spindle nose camlock = 6 ï?· Spindle hole diameter = 52mm ï?· Spindle speed = 0-2200 rpm ...
Lathe, lathe, master and center lathe -Turning length 900 mm -Turning Ø over bed 280 mm -Turning Ø over support 180 mm - Speeds 45 - 1980 rpm -Screw hole 30 mm -Chuck Ø 250 mm -Stick stock MK4 -Motor power 4 kW Quick change tool holder Multifix -Dimensions 2290/700 / H1380 mm -Weight 1600 kg
WAGNER DORTMUND HEAVY DUTY PLATE BENDING ROLLS FOR COLD/HOT ROLLING ------------------------------------------------------------------- 1. Top roll diameter: 900 mm 2 Bottom rolls diameter: 700 mm 3. Length of rolls: 6000 mm 4. The bottom rolls move up and down vertically 5. Total power requirement is 1000 kW 6. Rolls are suitable for cold and hot rolling Capacity: 75-100 mm x 6000 mm (cold) Weight of machine: 380,000 kg
Movable mounting table Fabr.WAGNER type: FE4000 BJ. 1980 Travel: X4000mm Clamping surface: 4000mmX1400mm Workpiece weight max: 12, 5T Screw drive, Hydraulischeklemmung Continuously feeds: 8-2500mm / min Creep: 8 mm / min Rapid traverse rate: 4000 mm / min Weight approx.: 15 t
cutting diameter: 340 mm saw band length: 5270 mm cutting width: mm cutting speed: 18-114 m/min cutting range: 340x340 mm multi station feed: 2080 mm chip conveyor: total power requirement: kW weight of the machine ca.: t dimensions of the machine ca.: m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Table size: 1370 x 355 mm Workspace in X: 745 mm Workspace in Y: 500 mm Workspace in Z: 500 mm Tool holder: SK 40 Speed range: 70-3600 RPM Total power consumption: 3.7 KW / 400 V Machine weight: approx. 2500 kg Equipment / Accessories: CNC control proto Trak A.G.E. 3 - version 2 swivelling vertical milling head automatic tool clamping Handwheel for manual editing Coolant system Documentation Other: can be used as: a) CNC milling machine b) NC milling machine (c) milling with active digital display (d) manual milling via handwheels with digital display All technical data are created according to our best knowledge and existing documents. Anyone can test the ma ...
turning diameter over bed: 3050 mm turning diameter over slide rest: 2500 mm turning length: 21200 mm Control: Siemens type: 840D turning speeds: 0,236-60 U/min faceplate: 3000 mm main drive motor: 200 kW tailstock quill diameter: 900 mm roll stand: steady: 1200 mm steady: 1200 mm steady: 750 mm steady: 750 mm with live steady: 2000 mm faceplate: 2000 mm Thickness: 330 mm workpiece weight: 200 t total power requirement: kW weight of the machine ca.: t dimensions of the machine ca.: m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Machine type: Cycles CNC Milling Machine (Multipurpose Bed-Type Milling Machine), Manufacturer: Wagner, Type/Model: DPM, Control: Proto Trak A.G.E.3, Year of construction: 1998, Machine condition: very good, Offer type: used machine, Technical data, Possible applications as:, - full-fledged CNC, - semi-automatic, - conventional, - active-digital, - easy to operate manual machine with digital display, , Table: 1372 x 355 mm, Table load max.: 450 kg, Paths:, x = 745 mm, y = 500 mm, z = 500 mm, Spindle speed: 70 - 3600 rpm, Spindle retainer: SK 40 with automatic tool clamping, Spindle drive: 3.7 kW, Remarks:, swiveling milling head, coolant system, Weight: 2500 k ...
thread dia.: 4 - 22 / 22 - 30 mm threading length: 4-22 beliebig 22-30 bis17 mm thread pitch: mm total power requirement: kW weight of the machine ca.: t dimensions of the machine ca.: m This is a self-opening thread cutting head for cutting outer threads, chasers and chaser holders are changeable in a few simple steps. This allows the heads a large cutting area for many types of threads. This makes it possible to quickly change from one type of threat cutting to the next. The heads generally remain on the machine. With left holders and chasers also suitable for left-hand threads. Suitable for use on revolver machines. The data for this ad was created with ModulMWS - the software solution ...
Workspace in x 650 mm Workspace in Y: 480 mm Workspace in Z: 510 mm Table size: 800 x 450 mm Speed range: 0 - 8000 RPM - infinitely variable Toolholder: BT 40 Total power consumption: 7.0 / 9,25 KW / 400 V Machine weight: 3500 kg Equipment / Accessories: CNC railway control Siemens 802 D 16 x tool changer Electr. Handwheel Coolant system Pole-reversible motor All technical data are created according to our best knowledge and existing documents; Expressly reserved by mistake. Each party has the opportunity to test the BAZ before making a purchase in our factory under power.
turning diameter over bed: 3600 mm turning diameter over slide rest: 3150 mm turning length: 22000 mm centre height: 1800 mm centre distance: 22000 mm bed width: 3470 mm workpiece weight: 200 t faceplate diameter: 3600 mm spindle turning speed range: 0,1 - 40 (4 Stufen) U/min feeds X-axis: 0,05 - 100 mm/U feeds Z-axis: 0,025 - 30 mm/U diameter of quill: 830 mm stroke: 440 mm electrics - voltage/frequency: 400 / 50 V/Hz main gear-box motor: 150 kW rebuild in 2004 - Tailstock and toolposts have been overhauled - clutches were replaced or rewind - most of the bearings have been replaced - seals and hydraulic jacks are replaced - smaller works have been done machine is equipped with: - 3 tool p ...