We use cookies to optimize our website for you and to be able to continuously improve it. By continuing to browse the site you are agreeing to our use of cookies.
Disagree
the machine with two motors each 5.5 kw and blades 40 mm 2 hooks machine complete with hopper and stood and as well as a new control panel
This machine with two motors each 11 kw was used for tire recycling complete with hopper and control panel.
used
Guillotine shears, FASTI type 506-10-2,5 Masch. Nr. 96-506-018 Year of manufacture 1996 Cutting length 1030 mm Cutting thickness 2.5 mm Working height 850 mm Drive power 4 kW Mains connection 400 volts, 50 Hz. - mechanical sheet metal hold-down - electric foot switch - simple backgauge 550 mm with handwheel adjustment - 2 support arms 550 mm - angle stop right 750 mm - protective housing SICK behind the machine - control cabinet fixed to the machine space requirement L x W x H 2150 x 1650 x 1400 mm weight 650 kg good condition; used
used
COMPACTOR ROTATIV PENTRU CARTON, PLASTIC SI LAZI SAU CUTII DE CARTON Valpak ROTARY COMPACTOR FOR CARDBOARD, PLASTIC AND BOXES OR CARDBOARDS Valpak Brand/Marca TECHVAL Type/Model// Tip/Model VALPAK Putere/Power 4 kW Year of manufacture/an fabricatie 2003 Acustic pressure/nivel de zgomot 59 db (A) Supply voltage/alimentare 380 V triple phase Protection/protectie 16A curve D Sizes/Dimensiuni in cm Coil Weight – Al fins 140x210x280 cm (LxWxH) 1200 kg Amount in stock/pe stoc 1 pc/buc 1 sac rotund de deseu maruntit = 36 baxuri de carton necompactat 1 round bag of shredded waste = 36 containers of uncompressed cardboard 1 sac rotund de carton va avea 300/400 kg, de ladite 300 kg, plastic 200/300 kg 1 round cardboard bag will have 300/400 kg, of said boxes300 kg, plastic 200/300 kg Echipamentul standard are: Celulă fotoelectrică, sistem de debavurare automat, senzor op ...
used
Untha RS 100 HD four-shaft shredder. Very good condition. Cutting unit new! With control cabinet and insertion troughs. Drive power 2 x 55 kW. With new 30 mm perforated screen!
used
Rotor shears with feed hopper and base frame Demonstration machine with only 10 operating hours 2 x 15 kW Cutting unit 600 x 850 mm Rotor shear with hopper and feet demo machine with only 10 working hours 2 x 15kW Cutting chamber 600 x 850 mm
used
TECHNICAL SPECIFICATIONS Manufacturer: BHS Sonthofen Designation: Pre-ripper Type: VSR 1215 Version: Twin-shaft shredder / rotor shear Year of construction: 2018 Rotor diameter x length: 530 x 1,500 mm Operating hours: approx. 500 h Drive power: 2 x 90 kW Rotor speed (max.): 16 - 37 RPM Nominal torque: 33,000 Nm Number of tearing tools: 8 pcs. Width of tearing tools: 80 mm Total weight: approx. 22,000 kg SPECIFIC COMMENT - Incl. control cabinet/control - Incl. hydraulic pressure unit - Incl. steel substructure - Warranty for approx. 500 Bh - Shredding of domestic, commercial, bulky waste, waste wood, e-waste, plastics,...
used
Description: This forward-looking rotor blade ensures a fast and clean implementation of compost and other bulk materials. The material is taken up like a conventional wheel loader shovel. At the dispensing point, the rotor is started by means of the automatic control. The hydraulic rear panel pushes the material evenly to the rotor in dependence on the rotor speed. The opposite rotor mills off the bucket contents, whereby it is well mixed and loosely dropped. Optimal conditions are thus created for the composting process. Clumps and compactions are reliably dissolved and a well-mixed bulk material is produced. Advantages of using the meetra rotor blade: 1. - Maximum area utilization 2. - Excellent material mixing and loosening allow shortest dwell times 3. - Maximum annual throughput, as regardless of plant length and width 4. - Composting allows for trouble-free rotting c ...
new
FOR SALE... TAIKO TWO ROTOR SCREW PUMP TO WHOM IT MAY CONCERN WE VE NEW UNUSED TAIKO CSL-600 TWO ROTOR SCREW PUMP AT OUR STOCK THIS PUMP KEEPED AS SPARE PUMP AT TANKER VESSEL. PLS FIND SPEC AT BELOW. SERIAL NO.: NO. A1K6369 TYPPE: CSL-600 CAP: 560 m3/h REV: 1300MÄ°N POWER: 400PS DATE OF MANUFACTURE: NOV 2006 PUMP IS READY TO TRANSPORT AT WARE HOUSE. IF YOU INTEREST PLS DO NEED HESITATE TO CONTACT WITH US. Capt. Abu Ugurluba Best of regards; Aliaga marine services E mail: info/aliagamarine.com PHN/fax: 90 232 618 03 85 Mobile: 905556084850aliagamarine.com TURKEY
new
; New Diameter: 635mm Height: 590mm
used
Lobe rotor pump,stainless,acid proof steel,IBEX type NMOG/322,0,75 kW TEO Cap 2957 l/h.
new
TO WHOMIT MAY CONCERN ; WE VE NEW UNUSED COMPLETE ROTOR AND SHAFT ABB VTR 304 - P11 AT OUR STOCK ADDATIONALY WE VE RECON COMPLETE ROTOR AND SHAFT ABB VTR 304 - P11 COMPRESSOR SIDE AND TURBINE SIDE ARE NEW .. THIS ROTORS ARE FIT FOR BELOW EXHAUST TURBO CHARGER TYPE TYPE ABB VTR 304 P 11 HT 439312 n max 467 n bmax 443 t max 680 t bmax 650 HZTL 428765 P3 EX STOCK. IF YOU VE ANY FURTHER QUESTIONS PLS DO NOT HESITATE TO CONTACT WITH US Capt. Ayhan Ugurluba With Kind Regards ; Aliaga Marine Services E mail: info/aliagamarine.com Phn/Fax:+90 232 618 03 90 Mobile: +905556084850 aliagamarine.com TURKEY
used
Three-phase twin-rotor motor, three-phase electric motor, pole-changing motor VEM, ELECTRIC MOTOR PLANT GRÜNHAIN ADW938-A2 0,55 / 0,11 kW 2770 / 450 rpm 220 / 380 V 3AC IP 44 shaft diameter: Ø 12 / 15 mm, fan side: Ø 18 mm wavelength: 18 / 20 mm, fan side: 35 mm groove: 4 x 12 mm, fan side: 6 x 26 mm hole spacing (parallel to shaft): 30 / 88 / 30 mm hole spacing ( transverse to shaft ): 65 mm 8x threaded hole: M5 x 0.8, depth: 15 mm used, tested ! Dimensions: 390 x 205 x 160 mm
used
Linear motor with rotor LINMOT PS01-23x80-R Product no.: 0150-1233 stroke: max. 780 mm force: max. 44 N Nominal force : 8.6 / 16 N Max. Speed: max. 5.9 m/s stator diameter: Ø 23 mm stator length: 162 mm rotor diameter: Ø 12 mm Runner length: 130 mm (max. 850 mm possible) stator with IP67 connector M17/9(m) used, tested ! Dimensions ( packaging ): 195 x 35 x 75 mm
used
T-Rotor Pump, Gear Pump, Trochoid Pump, Feed Pump with Motor NIPPON GEROTOR CO. LTD. AMTP-216HA(VB) Q: 24.3 l/min p: 2.0 MPa ( 20 bar ) n: max. 1500 rpm Input: G3/4 Output: G3/4 Engine: ELQ-8T 1,5 kW 1430 rpm 200 V 3AC spare part for machining center MAZAK AJV25/405 ! used, tested ! Dimensions: 440 x 250 x 185 mm
used
Impeller with pump rotor for magnetic coupling centrifugal pump RICHTER CHEMIE-TECHNIK GmbH RMA 1,5 x 1 x 6 impeller, closed: D175 Material number: 9427-93-1006 diameter: 175 mm, width: 20 mm pump rotor: 50 Nm Material number: 9427-93-3002 Bearing bushing diameter: Ø 45 mm Shaft bushing: Ø 24.5 mm New ! Dimensions: 175 x 175 x 127 mm
used
Steam oven, built in 2006, in good condition, fully functional against bid from 76131 Karlsruhe
used
guillotine shears, sheet metal shears DIGEP type OL 3 Fabr. No. 1312 Year of construction 1977 Cutting length 1250 mm (nominal cutting length)Cutting length max. 1300 mm Cutting thickness at 450 N/mm² 3 mm single backgauge 500 mm Column projection 200 mm Cutting angle 2 Stroke rate at full cutting length max. 50 strokes/min. Working height 860 mm Motor power 2.2 kW Mains connection 380 volts, 50 Hz - LED cutting area lighting - simple backgauge with manual adjustment - Mechanical foot switch - Front angle stop left - 1 piece front sheet metal supports 300 mm Space requirement L x W x H 1660 x 1350 x 1200 mm Weight 1600 kg good condition; used
used
guillotine shears, sheet metal shears DIGEP type OL 3 Fabr. No. 1312 Year of construction 1977 Cutting length 1250 mm (nominal cutting length)Cutting length max. 1300 mm Cutting thickness at 450 N/mm² 3 mm single backgauge 500 mm Column projection 200 mm Cutting angle 2 Stroke rate at full cutting length max. 50 strokes/min. Working height 860 mm Motor power 2.2 kW Mains connection 380 volts, 50 Hz - LED cutting area lighting - simple backgauge with manual adjustment - Mechanical foot switch - Front angle stop left - 1 piece front sheet metal supports 300 mm Space requirement L x W x H 1660 x 1350 x 1200 mm Weight 1600 kg good condition; used
used
guillotine shears, sheet metal shears DIGEP type OL 3 Fabr. No. 1312 Year of construction 1977 Cutting length 1250 mm (nominal cutting length)Cutting length max. 1300 mm Cutting thickness at 450 N/mm² 3 mm single backgauge 500 mm Column projection 200 mm Cutting angle 2 Stroke rate at full cutting length max. 50 strokes/min. Working height 860 mm Motor power 2.2 kW Mains connection 380 volts, 50 Hz - LED cutting area lighting - simple backgauge with manual adjustment - Mechanical foot switch - Front angle stop left - 1 piece front sheet metal supports 300 mm Space requirement L x W x H 1660 x 1350 x 1200 mm Weight 1600 kg good condition; used
new
McIntyre 407 Shear An affordable efficient 407mm (16") blade shear with enough power and speed to handle a wide variety of cutting tasks Robust, affordable, efficient Built originally for scrapyard use, the McIntyre 407 shear is robust enough to withstand the most difficult of working environments. It is now our most popular alligator shear with more than 2000 still in daily use worldwide. The McIntyre 407 is able to handle; automotive scrap, whole gear boxes, cylinder heads and blocks, oversized gate valves and of course all the usual non ferrous metal separations. The 407 can also be used to cut ferrous metals. Why
new
McIntyre 500HD Shear This new generation shear is faster and more powerful than any other machine of its size. Featuring an automatic hold down clamp and 20 inch blade, this model is available as electric or diesel Fast and strong This 508mm, 20 inch, blade shear has been built for speed and power, and will outperform every other machine in its field. The McIntyre 500HD has enough shear force to deal with a wide range of operations and materials including: the cleaning of automotive aluminium scrap, whole gearboxes, cylinder heads and blocks, oversized gate valves, and the handling of all non-ferrous separations. It can also be used for cropping ferrous metals.
new
McIntyre 500HD Shear This new generation shear is faster and more powerful than any other machine of its size. Featuring an automatic hold down clamp and 20 inch blade, this model is available as electric or diesel Fast and strong This 508mm, 20 inch, blade shear has been built for speed and power, and will outperform every other machine in its field. The McIntyre 500HD has enough shear force to deal with a wide range of operations and materials including: the cleaning of automotive aluminium scrap, whole gearboxes, cylinder heads and blocks, oversized gate valves, and the handling of all non-ferrous separations. It can also be used for cropping ferrous metals.
used
Working width: 1040 mm sheet thickness: 12 mm rear gauge: hand up to 500 mm power: 380 V, 11 kW space: 2500 x 2150 x 1900 mm weight: 4100 kg
new
McIntyre 600 GT Shear Another Shear in the McIntyre GT Range, the 600 gives a massive cutting area for its relatively diminutive size. Versatile The 600 GT features a blade guard system which gives good visibility to the operator and acts as a hold down to prevent material kick back. The machine is foot pedal operated and the jaws return to the open position once the foot pedal is released to increase safety. Wheels are fitted as standard, and forklift points have been included on the body of the machine to ensure that it can be safely lifted both within the yard and during transportation. Ideal for larger items such as car radiators which can be handled in just one pass, the 600 GT can also be adapted to process catalytic converters.