used RUBICON Rubber extruders

Troester.200mm H/F strainer M/C Number 7175-71 L/D 6.5/1 Roller Feed 350mm. Hinged strainer head with hydraulic clamp. 125KW AC v/s motor. On single bedplate. With controls.

Barwell C3 Preformer Extruder 2500 psi Output 600kg/hour Ram type Extruder Extruder size 250mm With Rotary Cutter 8 fixed speeds Year 1980

1 x Berstorff GmbH 250mm strainer extruder, Year of manufacture: 1988, L/D ratio 7:1, power roller feed (300mm wide), with 120kW, 1800rpm DC variable speed motor mounted on top of gearbox (belt drive), with tube head and knife at top for sheet extrusion. Complete with control panel etc and in very good condition.

Iddon HRX 4.5? (120mm) Cold Feed Rubber Extruder Year 1994 LD ratio 17:1 Bostock & Bramley Gearbox ABB Motor: 1994, 95kW, 1870 rpm, 419 amps, 360 volts With 1 x spare vacuum screw With Control Panel

8" Cold Feed Rubber Extruder

Single-screw rubber extruder with feed roller and degassing in screws of 70mm and a process length of 22.D - with two-speed temperature-controlled entagling screw - Degassing cylinder with device for static and/or vacuum degassing of the material - a vacuum block pump - two water temperature control units with 9kW heating capacity each, - a Siemens SPS S7 machine with Siemens KTP1200 HMI control panel - a directly driven feed roller feeder for rubber raw strips, a funnel-material stiffening system with Strip monitoring - temperable base body for tool holder and v.m

available Troester Triplex Extruder Top machine QSM 90x 16D Middle machine 200W x 6D Below machine QSM 150 x 16D Head MW500 Description attached!

Farrel Twin Screw / Rollerdie Extruder complete available with Motor and Inverter Description attached!

Refer to code 1042 in your request More information on our web page G3 Mixing Technologies - G3 STOCK or LinkedIn G3 STOCK Used machine, possibility to be purchased "as is" without warranty, or completely rebuilt and guaranteed as new machine.

Refer to code 1043 in your request More information on our web page G3 Mixing Technologies - G3 STOCK or LinkedIn G3 STOCK Used machine, possibility to be purchased "as is" without warranty, or completely rebuilt and guaranteed as new machine.

Refer to code 1044 in your request More information on our web page G3 Mixing Technologies - G3 STOCK or LinkedIn G3 STOCK Used machine, possibility to be purchased "as is" without warranty, or completely rebuilt and guaranteed as new machine.

Refer to code 1045 in your request More information on our web page G3 Mixing Technologies - G3 STOCK or LinkedIn G3 STOCK Used machine, possibility to be purchased "as is" without warranty, or completely rebuilt and guaranteed as new machine.

Refer to code 1046 in your request More information on our web page G3 Mixing Technologies - G3 STOCK or LinkedIn G3 STOCK Used machine, possibility to be purchased "as is" without warranty, or completely rebuilt and guaranteed as new machine.

Pin-Convert-Extruder, GE 120 SC, make Berstorff, cold lined

Profile extruder, GE 90 x 16 D vacuum, make Troester, cold lined

Berstorff Strainer Extrusion Line Consisting of: Extruder Supplier Berstorff Type GE 150KSx16D Year of construction 2007 Pins: 12 Pins per level: 8 Condition: good Weight approx. 10000 kg Screen change: hydraulic, bladder accumulator 20lt / 300Bar D = 200mm Gear pump Supplier: Maag Pump Systems Type: extrex® 110-5 RV Volume 716 cm³ / rev Year of construction 2013 Condition: good Heaters Supplier: Regloplas Type P140 Year of construction various Number 5 pcs. Cooling bath Cooling medium Water above, 2 rows below with 4 fans each Year of construction 2006 Condition: good Dimensions 9m Weight approx. 500 kg Especially 8 fans Installation tape Year of construction 2006 Condition: good Weight about 300 kg

Francis Shaw 30mm Extruder Roller Feed LD ratio 15:1 Year 1993

Berstorff 8inch (200mm) Cold Feed Pin Extruder Manufactured by: Krauss Maffei Berstorff Extruder Type: Vac GE 200 SC, Pin Type No of Pins: 2 X10 + 1X12 (Hydraulic adjustment) Screw Diameter: 8"/200 mm L/D ratio 18:1 Drive: 300 Kw, 1500 RPM Screw speed: 33pm Complete with Control Panel Roller Die Suitable for rubber compounds Year 2009

Berstorff 6inch (150mm) Strainer Extruder Manufactured by: Krauss Maffei Berstorff Model: GE 150 K Screw Diameter: 6"/150 mm L/D Ratio: 6 Speed: Variable, up to 45 rpm Motor: 90 KW, 1500 RPM Transmission: Direct Drive, 3 steps reduction Gear Reduction Ratio: 33:1 Year 2009

Key data: 200 mm, 18

available Berstotff Rollerhead - Extruder Cold Feed Extruder - 200mm x 218D 2 roll calendars 400mm x 1200mm see attached description!

Iddon 75mm Cold Feed Rubber Extruder With roller feed With motor, gearbox and control panel

L/D=20.7 External dimensions 2700×1000×1400(LxWxH) Screw stiffness HRC65-68 Screw diameter 90mm Engine power 30KW/1470rpm SCREW LENGTH 1860 mm Heating section number/power 6kw×2

Key data: 120 mm, 18 , 45 1/min

Screw with vacuum zone, output approx. 255 - 400 kg/h, straight head

Key data: 90 mm, 12

Extruding height 1010 mm, Mailefer screw,

Key data: 90 mm, 16

available Triplex Extruder- Cold Feed with head and feeder. Description attached!