rolls used for sale

Combined Cycle Gas Turbine Power Plant 75 MW/50 Hz – Zero Hours This equipment was delivered in 2017 by an EPC contractor who selected Rolls-Royce and Siemens as main equipment suppliers. This was a greenfield project and therefore delivery contained all equipment needed for 75 MW power plant operation, like fuel gas treatment plant, water treatment plant and complete switchyard with step-up transformers Manufacturing year: 2017 Gas turbine: Rolls-Royce Trent 60, Dry Low Nox Steam turbine: Siemens SST-300 Step up tranfomers: 2 pc Alstrom 11kV to 154 kW Complete switchyard: Siemens 154 kV Nominal output 100%: 60 MW + 15 MW Max efficiency: Single cycle 42 %, combi cycle 54% Heat recovery steam boiler: 30 bar / 300 C Water treatment: Sand and active coal filters + RO Documentation: Complete original in English Delivery: Complete plant equipment from water and gas t ...

Rolls-Royce Olympus SPEED SIGNAL GENERATOR from the stock of the Army Navy Unused or overhauled

Rolls-Royce Olympus SPEED SIGNAL GENERATOR from the stock of the Army Navy Unused or overhauled

Rolls Royce Bergen B32:40 L6P engines for sale in our stock in Istanbul Turkey Bergen B32:40 L6P complete engine with turbo charger In our stock in Istanbul 3 pieces available year: 2002 3000 kw 750 RPM in good condition please contact : info@fin-marine.com

Bergen Rolls Royce B35:40V20AG complete gas power plant Year of Make 2011 running hours: 16.380 Hours 8415 Kw 11kV 50 Hz at 750 RPM with AVK DIG 167 f/8 alternator 9100 kvA Complete power plant with all auxilaries: Control Air Compressor ,Self Demand Transformer, LT cooling water system, cooling tower, HT cooling water system, cooling tower, cooling fans, Start Air Compressors and Air tank, Natural Gas Regulator Unit, Emergency Diesel Generator 220 kVA, piping systems oil filter and heater exchangers, Neutral Earthing Resistor Unit, Generator Cooling Fans, Steam Boiler: Nooter/Eriksen Capacity: 5.5 T/h, Switchgear Units, engine tools, instruction manual and more... Please contact for more info and complete scope / offer

Key data: 3155

Make and Model: Rolls Royce KVSG 18 G4 The engine is from 1994. It had a full rebuild in 2004. Fuel: Natural Gas Capacity: 3155kW Hours: 63,000 HZ: 50 V: 10500 Scope of Supply: Engine, Alternator, Base frame, Acoustic Container, Exhaust Gas Heat Exchanger, Control panel and synchronisation panels. Please note: circuit breaker and transformers are not included. Price: €200,000

Cylinder head, Bergen BRM Lower OD 430 mm, upper OD 420 mm Draw. no. 528/15-1 Reconditioned Part no: 403690 Part no: 528/15-1

Bergen L 32:40 P cylinder head covers complete. 6 pieces available also available all other major parts like: connecting rods, pistons, crank shaft, turbo charger, camshaft piece , fuel pumps etc. In our stock in Istanbul Turkey Please contact us at: info@fin-marine

TO WHOM IT MAY CONCERN; WE VE NEW UNUSED GENUINE COMPLETE CYLINDER HEADS OF BERGEN B 32:40 A AT OUR STOCK PART NO IS 433549 WE VE 2 PCS AT OUR STOCK. EX STOCK IZMIR TURKEY ADDITIONALLY WE VE MANY MANY OTHER MAJOR PARTS OF THIS TYPE ENGINE BERGEN B 32:40 A AT OUR STOCK PLS REFER LIST ON ATACHE IF YOU VE ANY FURTHER QUESTIONS PLS DO NOT HESITATE TO CONTACT WITH US . Capt. Ayhan Ugurluba With Kind Regards ; Aliaga Marine Services E mail: info/aliagamarine.com Phn/Fax:+90 232 618 03 85 Mobile: +905556084850 aliagamarine.com TURKEY

TO WHOM IT MAY CONCERN; WE VE NEW UNUSED GENUINE CYLINDER LINERS OF BERGEN B 32:40 A AT OUR STOCK PART NO IS 102001 WE VE 2 PCS AT OUR STOCK. EX STOCK IZMIR TURKEY ADDITIONALLY WE VE MANY MANY OTHER MAJOR PARTS OF THIS TYPE ENGINE BERGEN B 32:40 A AT OUR STOCK PLS REFER LIST ON ATACHE IF YOU VE ANY FURTHER QUESTIONS PLS DO NOT HESITATE TO CONTACT WITH US . Capt. Ayhan Ugurluba With Kind Regards ;

WARTSILA 32 FUEL OIL PART NO: 473200, BERGEN BRM LUBE OIL: 022899 BERGEN BRM, WARTSILA, DEUTZ KHD/MWM, MAN B&W, JENBACHER, ABC, PIELSTICK , GUASCOR, MAK, CATERPILLAR, VOLVO, WICHMANN, PUMPS, SACM, SEPERATOR, COMPRESSSOR, FILTER, PUMPS, VACUUM SAVAGE SYSTEM, HEAT EXCHANGER & COOLER. Spares are available and all kinds of spare parts can be given. Please contact us for your questions. EVE International AS E-Posta : info@eveinternational.com.tr Phone : +90 0216 519 2707 Fax : +90 0216 519 2720

BERGEN ENGINE TYYE B, PISTON RING SET PART NO: 413412 DRW 662/58. BERGEN BRM, WARTSILA, DEUTZ KHD/MWM, MAN B&W, JENBACHER, ABC, PIELSTICK , GUASCOR, MAK, CATERPILLAR, VOLVO, WICHMANN, PUMPS, SACM, SEPERATOR, COMPRESSSOR, FILTER, PUMPS, VACUUM SAVAGE SYSTEM, HEAT EXCHANGER & COOLER. Spares are available and all kinds of spare parts can be given. Please contact us for your questions. EVE International AS E-Posta : info@eveinternational.com.tr Phone : +90 0216 519 2707 Fax : +90 0216 519 2720

BERGEN BRM GASKET KIT, CYLINDER HEAD MAINTENANCE KIT, O-RING KIT AVAILABLE IN OUR STOCK. BERGEN BRM, WARTSILA, DEUTZ KHD/MWM, MAN B&W, JENBACHER, ABC, PIELSTICK , GUASCOR, MAK, CATERPILLAR, VOLVO, WICHMANN, PUMPS, SACM, SEPERATOR, COMPRESSSOR, FILTER, PUMPS, VACUUM SAVAGE SYSTEM, HEAT EXCHANGER & COOLER. Spares are available and all kinds of spare parts can be given. Please contact us for your questions. EVE International AS E-Posta : info@eveinternational.com.tr Phone : +90 0216 519 2707 Fax : +90 0216 519 2720

BERGEN INJECTION PUMP KITS. BERGEN BRM, WARTSILA, DEUTZ KHD/MWM, MAN B&W, JENBACHER, ABC, PIELSTICK , GUASCOR, MAK, CATERPILLAR, VOLVO, WICHMANN, PUMPS, SACM, SEPERATOR, COMPRESSSOR, FILTER, PUMPS, VACUUM SAVAGE SYSTEM, HEAT EXCHANGER & COOLER. Spares are available and all kinds of spare parts can be given. Please contact us for your questions. EVE International AS E-Posta : info@eveinternational.com.tr Phone : +90 0216 519 2707 Fax : +90 0216 519 2720

BERGEN NOZZLE PART NO: 700873, DRAW 662/22-11, DETAILS: VUO-U9019C/E MAN B&W ATOMIZER PART NO: 07793470 AND 07793254 BERGEN BRM, WARTSILA, DEUTZ KHD/MWM, MAN B&W, JENBACHER, ABC, PIELSTICK , GUASCOR, MAK, CATERPILLAR, VOLVO, WICHMANN, PUMPS, SACM, SEPERATOR, COMPRESSSOR, FILTER, PUMPS, VACUUM SAVAGE SYSTEM, HEAT EXCHANGER & COOLER. Spares are available and all kinds of spare parts can be given. Please contact us for your questions. EVE International AS E-Posta : info@eveinternational.com.tr Phone : +90 0216 519 2707 Fax : +90 0216 519 2720

The power plant, based on a 5 MW gas turbine CENTRAX 501 KB7 is complete with all needed equipment, allowing a steam output of 20 tons per hour at 20 bar. From ZERO hours until the last working day all maintenance was performed by Centrax under full maintenance contract.

Drive rolls, return rolls, conveyor belts, belt curves various dimensions RA2010 Various drive rollers and idlers for conveyor belts and belt curves in different lengths, angles and diameters Prices net plus VAT from central warehouse Dr. Sonntag GmbH & Co KG, 97076 Würzburg Features: For individual, professional advice, simply contact us. Simply contact us by phone or e-mail. We will be happy to help you with the planning and implementation of your projects. We look forward to hearing from you. With kind regards Your team at Dr. Sonntag GmbH & Co. KG Your specialist and contact for intralogistics

Sheet thickness: 25,00 mm Bending length: 3000 mm Number of rolls: 3   Hydraulic drop end Digital read out position side rolls Pendent control position side rolls Rolling width:                 3000mm Rolling thickness 3x toproll Ø:22mm Rolling thickness 5x toproll Ø:25mm Rolling thickness prebending:  16mm Top Roll Ø:                    420mm Side roll Ø:                   405mm Number of rolls:               3 Rolling speed:                 6,5 Length:                        5800mm Width:                        &nbs ...

Sheet thickness: 3,00 mm Bending length: 1500 mm Number of rolls: 3   MACH-id    5171 MAKE        Birlik TYPE         MSM YOP          2006 SPECIFICATIONS Control       Conventionel Hydraulic / Mechanical      Mechanical 3 or 4 roll       3 roll Maximum sheet thickness      3 mm Bending length       1500 mm Max. Rolling capacity Ø 2.500       3 mm Max. Prebending capacity Ø 2.500         2.5 mm Top Roll Ø     110 mm Bottom Roll Ø      110 mm Side Rolls Ø     110 mm DIMENSIONS Length        2400 mm Width       980 mm Height       1 ...

Sheet thickness: 2,00 mm Bending length: 1020 mm Number of rolls: 3   MACH-id   5016 MAKE        Huvema Holland TYPE          HU 1020 x 2 YOP             2011 SPECIFICATIONS Hydraulic / Mechanical         Mechanical 3 or 4 roll      3 roll Bending length        1020 mm Max. Rolling capacity Ø 2.500        2  mm Top Roll Ø75 mmBottom Roll Ø  75 mm Side Rolls Ø    75 mm Power      0,75 kW DIMENSIONS Length       1600 mm Width         1000 mm Height         1200 mm  

Sheet thickness: 4,5 mm Bending length: 1540 mm Number of rolls: 3   MACH-id    5011 MAKE         NOSSTEC LUNA Sweden TYPE           8266 15/45 YOP              1997 SPECIFICATIONS Hydraulic / Mechanical     Mechanical 3 or 4 roll        3 roll Bending length         1540 mm Max. Rolling capacity Ø 2.500     4.5 mm Max. Prebending capacity Ø 2.500      3.5 mm Top Roll Ø     120 mm Bottom Roll Ø      120 mm Side Rolls Ø        120 mm Power        1,1 kW DIMENSIONS Length       2100 mm Width         1000 mm Height        1200 mm  ...

Sheet thickness: 100,00 mm Bending length: 3000 mm Number of rolls: 4   Make Haeusler 100 mm Type VRM HY Year 1994 Heavy Duty 4 roll plate benderS heet thickness (mm)T = 100 mm Bending length (mm)Pre = 80 mm Number of rolls L = 3.000 mm Top roll = 780 mm        Side roll = 750 mm     Hydro 2 roll power 165 kW CNC Controlled Double side support Top support Conical bending attachment Weight 125 ton  

Sheet thickness: 8,00 mm Bending length: 1000 mm Number of rolls: 3   2 driven rolls Hydraulic tilting lateral roll Rolls on ball bearing Smallest bending diameter ca 165 mm Rolling width:                 1.000mm Rolling thickness 3x toproll Ø:7mm Rolling thickness 5x toproll Ø:8mm Rolling thickness prebending:  6mm Top Roll Ø:                    135mm Side roll Ø:                   135mm Number of rolls:               3 Rolling speed:                 5m/min Adjustment side rolls:         100mm Number of driven rolls:        2 Power:                ...

3-roll hydraulic with dual pre-pinch planetary configuration. new to complete, 45 days from order. -Plate width 3000 mm -Capacity rolling plate thickness 50 mm -Pre-pinch plate thickness 40 mm Machine configuration and accessories installed: -useful surface length on the rolls 3100 mm -upper roll size 480 mm -lower rolls size 440 mm -Digital position readouts. -Hardening treatment of the 3 rolls. -3 rolls driven hydraulic motorized with independent axial gear box on each roll. -Conical plate bending attachment with tiltable lower rolls hydraulic. -CE quality certification, Made in Italy manufacturing. -Service manuals and operation instruction manuals. -Hydraulic diagrams -Electric & electronic schematics with parts list. -Set of service tools for maintenance. -Electric power installed 50Hp. -3 phase voltage to be specified Warranty 12 months.  ...

Sheet thickness: 40,00 mm Bending length: 3050 mm Number of rolls: 3   Top support Variable geometry with three movebale rolls Linear slidews for roll movement Lubricatipon system Separate pendant control with optical position side rolls Rolling width:                 3050mm Rolling thickness 3x toproll Ø:30mm Rolling thickness 5x toproll Ø:40mm Rolling thickness prebending:  20mm Top Roll Ø:                    420mm Side roll Ø:                   380mm Number of rolls:               380 Rolling speed:                 0 - 5 Adjustiment lower roll:        200mm/min. Adjustment side rolls:        ...

Sheet thickness: 14,00 mm Bending length: 300000 mm Number of rolls: 3   3 roll plate benderSTOLTING - SRAH MACH-ID 7648 Make: STOLTING Type: SRAH Year: 2000 Hardned and grounded rolls Conical bending attachment Digital read out positioning side rolls CE-Mark  Fully hydraulic opperated Central lubrication Rolling width:                 3000mm Rolling thickness 3x toproll Ø:12mm Rolling thickness 5x toproll Ø:14mm Rolling thickness prebending:  8mm Top Roll Ø:                    300mm Side roll Ø:                   300mm Number of rolls:               3 Rolling speed:                 0 - 5 Adjustment side rolls:   ...

Key data: 188 , 3100 , 4

Sheet thickness: 188,00 mm Bending length: 3100 mm Number of rolls: 4   Without side support Conical bending attachment Oil cooler Separate hydraulic power unit Central lubrication Rolling width:                 3.000mm Rolling thickness 3x toproll Ø:34mm Rolling thickness 5x toproll Ø:38mm Rolling thickness prebending:  32mm Top Roll Ø:                    460mm Bottom Roll Ø:                 440mm Side roll Ø:                   330mm Number of rolls:               380 Rolling speed:                 2 + 4 m/min Adjustiment lower roll:        0 - 200 mm/min. Adjustm ...

Key data: 13 , 2000 , 4

Sheet thickness: 13,00 mm Bending length: 2000 mm Number of rolls: 4   Rolling width:                 2.000mm Rolling thickness 3x toproll Ø:10mm Rolling thickness 5x toproll Ø:13mm Rolling thickness prebending:  8mm Top Roll Ø:                    230mm Bottom Roll Ø:                 230mm Side roll Ø:                   195mm Number of rolls:               4 Rolling speed:                 5m/min Adjustiment lower roll:        100mm/min. Adjustment side rolls:         150mm/min. Number of driven rolls:        2 Power:    ...

Sheet thickness: 30,00 mm Bending length: 3000 mm Number of rolls: 4   Rolling width:                 3.000mm Rolling thickness 3x toproll Ø:22mm Rolling thickness 5x toproll Ø:30mm Rolling thickness prebending:  20mm Top Roll Ø:                    420mm Bottom Roll Ø:                 400mm Side roll Ø:                   300mm Number of rolls:               4 Rolling speed:                 0 - 4 m/min Adjustiment lower roll:        200mm/min. Adjustment side rolls:         200mm/min. Number of driven rolls:        2 Power:  & ...

Sheet thickness: 12,00 mm Bending length: 1200 mm Number of rolls: 4   CNC Brand: Siemens CNC Model: OP7 Davi Promau - MCB 1222 CNC 4 roll plate bender 1200 x 12 mm MACH - ID 6411 Make: Davi Promau Type: MCB 1222 Control: Siemens OP7 YOP: 2004 Rolling width:                 1.200mm Rolling thickness 3x toproll Ø:10mm Rolling thickness 5x toproll Ø:12mm Rolling thickness prebending:  8mm Top Roll Ø:                    220mm Bottom Roll Ø:                 200mm Side roll Ø:                   180mm Number of rolls:               4 Rolling speed:                 0 - 5 m/min Adjustiment lower  ...

Sheet thickness: 150,00 mm Bending length: 3000 mm Number of rolls: 4   MACH-id     5563 MAKE          Haeusler TYPE           VRM-HY YOP             1990 / 2000 SPECIFICATIONS Rolling width         3000 mm Rolling thickness 3x toproll Ø     120 mm Rolling thickness 5x toproll Ø      150 mm Rolling thickness prebending       100 mm Top Roll Ø          910 + 820 + 740 mm Bottom Roll  Ø    940 mm Side roll Ø           780 mm Number of rolls    4 Rolling speed        2 + 4 m/min Adjustiment lower roll        200 mm/min. Adjustment side rolls    &nbs ...

Sheet thickness: 20,00 mm Bending length: 3000 mm Number of rolls: 4   incl. hydraulic top support incl. side support incl. spare roll 300 mm ( small cones) Rolling width:                 3.000mm Rolling thickness 3x toproll Ø:20mm Rolling thickness 5x toproll Ø:25mm Rolling thickness prebending:  18mm Top Roll Ø:                    430 + 300 mm Bottom Roll Ø:                 430mm Side roll Ø:                   300mm Number of rolls:               4 Rolling speed:                 2 + 4 m/min Adjustiment lower roll:        200mm/min. Adjustment side rolls:    & ...

Sheet thickness: 14,0 mm Bending length: 2100 mm Number of rolls: 4   CNC Brand: _Unknown / Other CNC Model: Bend iT 7 Axis Touchscreen Bend iT Cone bending device Hardned rolls (Hrc 58) Force lower roll to upper roll 70 Ton New over EUR 100.000 Rolling width:                 2.100mm Rolling thickness 3x toproll Ø:10mm Rolling thickness 5x toproll Ø:14mm Rolling thickness prebending:  10mm Top Roll Ø:                    260mm Bottom Roll Ø:                 250mm Side roll Ø:                   180mm Number of rolls:               4 Rolling speed:                 0 - 8 m/min Number of dri ...

Sheet thickness: 50,00 mm Bending length: 3100 mm Number of rolls: 4   CNC Brand: _Unknown / Other CNC Model: DAVI EASY Rolling width:                 3100mm Rolling thickness 3x toproll Ø:40mm Rolling thickness 5x toproll Ø:50mm Rolling thickness prebending:  40mm Top Roll Ø:                    530mm Bottom Roll Ø:                 470mm Side roll Ø:                   400mm Number of rolls:               4 Rolling speed:                 0 - 5 Adjustiment lower roll:        0 - 200mm/min. Adjustment side rolls:         0 - 200mm/min. Top support:  ...

Sheet thickness: 7,00 mm Bending length: 1000 mm Number of rolls: 1   Max plate thickness : 7 mm Min. rolling diameter : 760 Max. rolling diameter : 600 Top Shaft diameter : 110 Lower rolls diameter : 120 Max. bending power : 350.000 N Rolling width        1,000 mm Rolling thickness prebending       7 mm Number of rolls     1 Number of driven rolls       1 Power     2.4 kW

Sheet thickness: 6,00 mm Bending length: 1000 mm Number of rolls: 1   MACH - ID 6112 Make:ROUNDO Type:PM 22 YOP:2007 Max plate thickness : 6 mm Min. rolling diameter : 160 Max. rolling diameter : 600 Top Shaft diameter : 110 Lower rolls diameter : 120 Max. bending power : 350.000 N Rolling width   1,250 mm Rolling thickness prebending      6 mm Number of rolls      1 Number of driven rolls    1 Power       5.4 kW

Sheet thickness: 45,00 mm Bending length: 2500 mm Number of rolls: 4   Make Stolting 45 mm Type VB 2500 / 45 Year 1954 roll hydraulic plate rolls rundwalze blechbiege Sheet thickness (mm) Bend = 45 mm Bending length (mm) Pre = 35 mm Number of rolls Length = 2500 Top rol 480/480/390 sideTop & side support Digital readout pos. rolls  

Sheet thickness: 10,00 mm Bending length: 2050 mm Number of rolls: 4   Make MG 10 mm Type MH 2010 B Year 2009 4 walzen rundbiege plate roll blechrundbiege mg Sheet thickness (mm) T = 10 mm Bending length (mm) L = 2.050 Number of rolls Pre = 6 mm Top roll = 210 2 rolls driven Digital read out Hardened rolls 55 Hrc Fully hydraulic CE Saftety  

Used plastic rollers for flow rack - Roller strip - Picking rack - 100 pieces - white Properties: - Rolls compatible with many manufacturers of flow racks - Spare rolls in practical bag - Rollers are mounted in the click system - Manufacturer: SSI Schaefer - Color: white - Used, in very good condition - Rolls made of robust polypropylene (PP) - Rollers with stable plastic axle / partly also steel axles Metrics: - Roller width: 25 mm - Roller diameter: 26 mm - Axle width: 34 mm - Axle diameter: 4 mm Scope of delivery: - 100 pieces of rolls (without mounting profile) All information without guarantee. The shipment takes place within Germany (except islands) free unloading point, without unloading, without contracting, without assembly. Island shipping excluded.

Used plastic rollers for flow rack - Roller strip - Picking rack - 100 pieces - yellow Properties: - Rolls compatible with many manufacturers of flow racks - Spare rolls in practical bag - Rollers are mounted in the click system - Manufacturer: SSI Schaefer - Color: yellow - Used, in very good condition - Rolls made of robust polypropylene (PP) - Rollers with stable plastic axle / partly also steel axles Metrics: - Roller width: 25 mm - Roller diameter: 26 mm - Axle width: 34 mm - Axle diameter: 4 mm Scope of delivery: - 100 pieces of rolls (without mounting profile) All information without guarantee. The shipment takes place within Germany (except islands) free unloading point, without unloading, without contracting, without assembly. Island shipping excluded.

Sheet thickness: 60,00 mm Bending length: 3000 mm Number of rolls: 4   Rolling width:                 3000mm Rolling thickness 3x toproll Ø:60mm Rolling thickness 5x toproll Ø:70mm Rolling thickness prebending:  55mm Top Roll Ø:                    660mm Bottom Roll Ø:                 650mm Side roll Ø:                   550mm Number of rolls:               4 Rolling speed:                 0 - 3 M/Min Adjustiment lower roll:        0 - 300mm/min. Adjustment side rolls:         0 - 300mm/min. Number of driven rolls:        2 Power:& ...

Sheet thickness: 12,00 mm Bending length: 2500 mm Number of rolls: 4   CNC Brand: _Unknown / Other CNC Model: PASS 270 Rolling width:                 2500mm Rolling thickness 3x toproll Ø:10mm Rolling thickness 5x toproll Ø:12mm Rolling thickness prebending:  8mm Top Roll Ø:                    270mm Bottom Roll Ø:                 270mm Side roll Ø:                   215mm Number of rolls:               4 Rolling speed:                 0 - 6 Adjustiment lower roll:        200mm/min. Adjustment side rolls:         200mm/min. Control:      ...

Sheet thickness: 110,00 mm Bending length: 3500 mm Number of rolls: 4   CNC Brand: Siemens CNC Model: Siemens TOUCH Rolling width:                 3500mm Rolling thickness 3x toproll Ø:80mm Rolling thickness 5x toproll Ø:110mm Rolling thickness prebending:  90mm Top Roll Ø:                    900mm Top Roll Ø:                    900mm Bottom Roll Ø:                 800mm Side roll Ø:                   600mm Number of rolls:               4 Rolling speed:                 0-6 Adjustiment lower roll:        0-200mm/min. Adjustme ...

Sheet thickness: 14,00 mm Bending length: 2050 mm Number of rolls: 4   CNC Brand: _Unknown / Other CNC Model: CNC DAVI TOUCH Motorised Top support 1200 kg Hardned rolls 48-62 HR Rockwell C Conical bending attachment Minimum rolling diameter 270 mm   Rolling width:                 2050mm Rolling thickness 3x toproll Ø:12mm Rolling thickness 5x toproll Ø:14mm Rolling thickness prebending:  10mm Top Roll Ø:                    240mm Bottom Roll Ø:                 230mm Side roll Ø:                   180mm Number of rolls:               4 Rolling speed:                 6 Adjustiment  ...

Sheet thickness: 70,00 mm Bending length: 3050 mm Number of rolls: 4   Rolling width:                 3050mm Rolling thickness 3x toproll Ø:60mm Rolling thickness 5x toproll Ø:70mm Rolling thickness prebending:  50mm Top Roll Ø:                    630mm Bottom Roll Ø:                 600mm Side roll Ø:                   500mm Number of rolls:               4 Rolling speed:                 0 - 5 Adjustiment lower roll:        200mm/min. Adjustment side rolls:         200mm/min. Number of driven rolls:        2 Power:    & ...

: neu : ca. 12 Wochen ab Auftrags : Türkei : 21600 € : 442.8 € : 1 : 1 : 2030 mm : 6 mm : 6 mm : 5 mm : 170 mm : 4 kW : 3600 mm : 1020 mm : 1120 mm : 2400 kg 3 rolls Asymmetrical rolls arrangement - with pre-bending 2 driven rolls Motorized adjustment of lateral and clamping roll Digital read-out for lateral and clamping roll Swiveling top roll to the front Forward/reverse run Hardened rolls Moveable control panel User manual in GERMAN and ENGLISH (sample photo) The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

: neu : 2023 : 9659 : prompt, Zwischenverkauf v : Türkei : 18000 € : 369 € : 1 : 2050 mm : 3 mm : 130 mm : 3,5 m/min : 2.2 kW : 3200 mm : 750 mm : 1000 mm : 1500 kg 3 rolls asymmetric rolls - prebending 2 rolls driven by brakemotor HARDENED ROLLS manual Back Roll forward tiltable upper roll forward and reverse revs conical bending by tilt of backroll movable control panel users manual in GERMAN OPTIONS: Motorised Back Roll (Power Rear Roll)€ 1.200,- Digital Read-Out€ 1.200,- The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

: neu : ca. 12 Wochen ab Auftrags : Türkei : 19600 € : 401.8 € : 1530 mm : 6 mm : 6 mm : 4 mm : 150 mm : 4 kW : 3100 mm : 1120 mm : 1020 mm : 2100 kg 3 rolls Asymmetrical rolls arrangement - with pre-bending 2 driven rolls Motorized adjustment of lateral and clamping roll Digital read-out for lateral and clamping roll Swiveling top roll to the front Forward/reverse run Hardened rolls Moveable control panel User manual in GERMAN and ENGLISH (sample photo) The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Sheet thickness: 10,00 mm Bending length: 3000 mm Number of rolls: 4   Rolling width:                 3.000mm Rolling thickness 3x toproll Ø:7mm Rolling thickness 5x toproll Ø:10mm Rolling thickness prebending:  5mm Top Roll Ø:                    220mm Bottom Roll Ø:                 210mm Side roll Ø:                   165mm Number of rolls:               4 Rolling speed:                 0 - 5 m/min Adjustiment lower roll:        200mm/min. Number of driven rolls:        2 Power:                      & ...

Sheet thickness: 8,00 mm Bending length: 1050 mm Number of rolls: 4   Rolling width:                 1.050mm Rolling thickness 3x toproll Ø:8mm Rolling thickness 5x toproll Ø:10mm Rolling thickness prebending:  8mm Top Roll Ø:                    170mm Bottom Roll Ø:                 170mm Side roll Ø:                   145mm Number of rolls:               4 Number of driven rolls:        2 Power:                         2,2 kW Length:                        2.550 mm  Width:      ...