Category: 107 sheet metal working / Decoilers
Latest update: 29.03.2024 add to watchlist
approved
dealer
item-No.: 163301240

used

Location: Land-de

add to watchlist

sheet width - max.: 750-900 mm coil weight: 3,50 - 4,00 t coil internal dia.: 400 - 500 mm coil outside - diam. ca.: 1500 mm total power requirement: kW weight of the machine ca.: 1,90 t dimensions of the machine ca.: 1,50 x 1,90 x 2,30 m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Category: 107 sheet metal working / Decoilers
Latest update: 29.03.2024 add to watchlist
approved
dealer
item-No.: 163560102
New in: 1991

used


add to watchlist

sheet width - max.: 0250 mm coil weight: 0,500 t coil internal dia.: 250 - 550 mm coil outside - diam. ca.: 1150 mm total power requirement: kW weight of the machine ca.: t dimensions of the machine ca.: m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Category: 107 sheet metal working
Latest update: 28.03.2024 add to watchlist
approved
dealer
item-No.: 163675660
New in: 1988

used

check Seller: Vögtle Service GmbH
Location: Lager Eislingen, Baden-Württemberg

add to watchlist

material width:550 mm material thickness:0,4 - 1,6 mm no. of straightening rolls:11 straightening roll diameter:60 mm number of draw-in rolls:4 diameter of draw-in rolls:60 mm band speed:4 - 50 m/min power capacity:3,0 kW weight:1,7 t Dimensions (WxDxH):2,5 x 2,0 x 1,7 m

Category: 107 sheet metal working / Straighteners
Latest update: 28.03.2024 add to watchlist
approved
dealer
item-No.: 163674360
New in: 2020

used

check Seller: Surplex GmbH
Location: Eschenburg-Wissenbach Land-de

add to watchlist

Description: .DIMECO R 693 J+ sheet metal straightening machine y.o.m 2020! - Number of straightening rollers 17 - Number of pull rollers 2 - Pull rollers diameter 180 mm - Number of support rollers 147 - Largest roller distance 200 mm The machine is equipped with: - Control cabinet with drive outlets for height adjustment on the inlet/outlet side of the straightening cassette as well as for the two main drives connected in parallel - Hydraulic unit for the hydr. Movements of the infeed table and the delivery of the infeed driver - Support rollers firmly installed at the top and bottom - Documentation, digital only! - Additional, unused straightening roll cassettes with 17 straightening rolls and intermediate rolls at the top and bottom. The machine was until lately integrated into a fully automatic punching line, therefore it is necessary to complete the control system. There is al ...

Category: 107 sheet metal working
Latest update: 28.03.2024 add to watchlist
approved
dealer
item-No.: 163675656

used

check Seller: Vögtle Service GmbH
Location: Lager Eislingen, Baden-Württemberg

add to watchlist

material width:500 mm material thickness:0,6 - 1,6 mm no. of straightening rolls:7 straightening roll diameter:60 mm number of draw-in rolls:2 + 2 inlet roll diameter:60 mm max. material thickness:2,0 mm material thickness at 150 mm material width:2,0 mm material thickness at 500 mm material width:1,6 mm weight:0,5 t dimensions (WxDxH):0,8 x 1,0 x 1,2 m

Category: 107 sheet metal working
Latest update: 28.03.2024 add to watchlist
approved
dealer
item-No.: 163675659

used

check Seller: Vögtle Service GmbH
Location: Lager Eislingen, Baden-Württemberg

add to watchlist

material width:300 mm material thickness:0,6 - 2,5 mm no. of straightening rolls:7 straightening roll diameter:60 mm number of draw-in rolls:2 + 2 diameter of draw-in rolls:60 mm max. material thickness:3,5 mm material thickness at 30 mm material width:3,0 mm material thickness with 300 mm material width:2,5 mm weight:0,3 t Dimensions (WxDxH):0,9 x 1,0 x 1,1 m

Category: 107 sheet metal working
Latest update: 28.03.2024 add to watchlist
approved
dealer
item-No.: 163675674

used

check Seller: Vögtle Service GmbH
Location: Lager Eislingen, Baden-Württemberg

add to watchlist

material width:400 mm material thickness:0,6 - 2,8 mm no. of straightening rolls:5 straightening roll diameter:40 mm no. of pulling rolls:2 + 2 material thickness at 400 mm material width:1,8 mm material thickness at 65 mm material width:2,8 mm power capacity:3,0 kW weight:0,45 t Dimensions (WxDxH):0,8 x 1,8 x 1,35 m

Category: 107 sheet metal working
Latest update: 28.03.2024 add to watchlist
approved
dealer
item-No.: 163675770
New in: 1990

used

check Seller: Vögtle Service GmbH
Location: Lager Eislingen, Baden-Württemberg

add to watchlist

material width coil line:600 mm coil weight:2 x 3,5 t coil internal diameter:460 - 530 mm coil external diameter:1500 mm material thickness coil line:0,5 - 3,0 mm no. of straightening rolls:7 no. of rolls at in- and outlet:4 roll diameter:80 mm feed length:0 - 500 mm power requirement:10,0 kW weight:10,0 t dimensions of the coil line:8,8 x 4,0 x 2,55 m straightening machine:Dimeco, 1676 EV double decoiler:2382 FFPS lag brake:pneumatic electronic roll feed:Microfeed

Category: 107 sheet metal working
Latest update: 29.03.2024 add to watchlist
approved
dealer
item-No.: 163120507
New in: 2023

new

check Seller: HESSE+CO GesmbH
Location: Land-at
Price: 17.050 € add to watchlist

: neu : 2023 : 9676 : prompt, Zwischenverkauf v : Deutschland : 17050 € : 349.53 € : 1 : 1250 mm : 1.25 mm : 1,25 mm bei 1 Messerpaar, : 2 Stk. : 0.37 kW : 36 m/min : 70 mm : 1900 mm : 1600 mm : 1000 mm : 350 kg 3 PAIRS OF BLADES Length measuring by wheel Digital preselection of one position Brake motor Rubber feeding rolls Manual crosscutting equipment in front and behind blade shaft with 1 cutting slide which alternaingly can be used on front and backside User manual in GERMAN Options: Additional pair of blades € 510,- Additional cutting unit € 1.120,- The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Category: 107 sheet metal working / Cutting-To-Length Lines
Latest update: 18.03.2024 add to watchlist
approved
dealer
ankerimg
item-No.: 147022390
New in: 2006

used

check Seller: MET-TECH GMBH
Location: 61381 FRIEDRICHSDORF Land-de

add to watchlist

Qty. 1 Second-hand cut-to-length line Mfc.: Stratega Built: 2006 Direction right to left Strip width: 400 - 2020 mm Thickness: 0.4 – 2.5 mm De-coiler ID 508, 610 mm Weight: 25 Ton Length of sheets: 300 – 2000 mm Speed: 60 m/min. Leveller Tilting shear Magnetic belts stacker Consist of: Load cradle De-coiler Award spire Introduction table Leveller Feeder Towing pinch roll Tilting shear Evaquation shear wasting material Conveyor Magnetic stacker Eletrical panels & Control Hydraulic station Note: The lien has the guillotine that can cut metal sheet with trapez format cause the guillotine Can rotate or can be used as a normal cut-to-length line.

Category: 107 sheet metal working / Cutting-To-Length Lines
Latest update: 18.03.2024 add to watchlist
approved
dealer
ankerimg
item-No.: 150846397
New in: 1966

used

check Seller: MET-TECH GMBH
Location: 61381 FRIEDRICHSDORF Land-de

add to watchlist

Qty. 1 Second-hand cut-to-length line Mfc.: Ungerer Built: 1966 Material: Stainless steel Strip Width: 300 mm- 1500 mm Thickness: 1.5 mm (stainless steel) Cut length: 750 mm- 6000 mm Length adjustment: mechanical Coil weight: 9.000 kg Coil min/max inner Ø: 500 & 600 mm Shear Type: Rotary Hydraulic system Stacker capacity: 2000 ton PLC: Allen Bradley Scope of supply: Decoiler Crop shear Edge trimmer Leveller PVC film applicator Stacker Camera system

Category: 107 sheet metal working / Cutting-To-Length Lines
Latest update: 15.01.2024 add to watchlist
approved
dealer
item-No.: 152748124
New in: 1975

used

check Seller: HEGO Blechverarbeitungsmaschinen GmbH
Location: 76467 Bietigheim Land-de

add to watchlist

Technical data : Bandwidth / strip width: 1,800 mm Strip thickness / strip thickness: 0.5 - 1.5/2.0 mm Coil weight: 30,000 kg Coil inner/ coil inner-a: 508 mm Coil outer / coil outer-a: 2,000 mm

Category: 107 sheet metal working / Cutting-To-Length Lines
Latest update: 15.11.2023 add to watchlist
approved
dealer
item-No.: 158635300

used

check Seller: MAchine MW
Location: Land-es

add to watchlist

Cut to length line Bronx CTL 1-5mm 400-1500 15 MT Material: CR, HR, P&O GALVA Thick (mm): 1,0 – 5.0 Width (mm): 400 – 1500 Weight max: 20 MT Coil Int. Diam.: 508/610/700 Coil Ext. Diam max (mm): 2000 Length Produced (mm): 500 – 4000

Category: 107 sheet metal working / Cutting-To-Length Lines
Latest update: 15.11.2023 add to watchlist
approved
dealer
item-No.: 158635307

used

check Seller: MAchine MW
Location: Land-us

add to watchlist

60″ x .105″ x 20000Lb Strilich – Voss Cut to length line Make: Strilich – Voss Material Width: 12″ – 60″ Material Thickness: .020″ – .105″ Weight Capacity: 20,000Lb Coil ID: 20″ Coil OD: 72″ Direction: Left to Right Entry 3-Arm Turnstile Powered Rotation ID Protective Bars Entry L-Type Coil Car Powered Lift & Traverse Self Contained Hydraulics Push Botton Controls Mandrel Uncoiler Powered Mandrel Expansion Powered Hold-Down Roll Sliding Base Feed-Up Motor Water Cooled Brake

Category: 107 sheet metal working / Cutting-To-Length Lines
Latest update: 15.11.2023 add to watchlist
approved
dealer
item-No.: 158642032

used

check Seller: MAchine MW
Location: Land-us

add to watchlist

Cut to length line 72″ x .075″ x 40000Lb Rowe / Herr Voss Make: Rowe / Herr Voss Material Width: 12″ – 72” Material Thickness: .020″ – .075” Weight Capacity: 40,000Lb Coil ID: 20″ Coil OD: 72” Speed: 160 feet per minute Sheet Max Length :12′ Direction: R-L Entry Coil Car Floor Standing V-Type Design Powered Lift & Traverse Control Panel Mandrel Uncoiler 4-Leaf Mandrel Powered Hold-Down Roll Motorized Expansion Feed-Up Motor Sliding Base Coil Straightener Driven Pinch Rolls Six (6) Adjustable Work Rolls DC Motor Drive Herr–Voss 6-Hi Precision Leveler Model: RH/84-1.500-19-9-6Hi Work Roll Width: 84″ Work Roll Diameter :1.500″ Number of Work Rolls: 19 Number of Back Up Flights: 9 Powered Work Rolls Adjustment 75HP DC Motor Drive Electrical Controls Rotary Edge Trimmers Mechanical Scrap Chopper Scrap Conveyor Fee ...

Category: 107 sheet metal working / Cutting-To-Length Lines
Latest update: 15.11.2023 add to watchlist
approved
dealer
item-No.: 158757356

used

check Seller: MAchine MW
Location: Land-us

add to watchlist

48″ x .076″ x 20,000Lb Rowe – Voss Cut to length line Cut to length line 48″ x .076″ x 20,000Lb Rowe – Voss Make: Rowe – Voss Material Width: 12″ – 48″ Material Thickness: .017″ – .076″ Coil Weight: 20,000Lb Coil ID: 20″ Coil OD: 72″ Entry V-Type Coil Car Mandrel Uncoiler with Hold-Down Roll 9-Roll Coil Straightener with DC Motor Voss 4-Hi Precision Leveler with 19 Work Rolls 1.156″ Work Roll Diameter 40HP Moto High Speed Shear Drop Type Stacker with Driven Conveyors

Category: 107 sheet metal working / Cutting-To-Length Lines
Latest update: 15.11.2023 add to watchlist
approved
dealer
item-No.: 158757358

used

check Seller: MAchine MW
Location: Land-us

add to watchlist

60″ x .135″ x 20,000Lb Dahlstrom CTL Line Coil Width: 12″ – 60″ Material Thickness: .015″-.135″ Coil ID: 20″-24″ Speed: 180 fpm Direction: Left to Right Entry Floor Standing Coil Car Mandrel Uncoiler with Powered Expansion Motorized Hold-Down Roll Feed-Up Drive Hydraulic Peeler 9-Roll Coil Straightener with 4″ Work Rolls Driven Entry Pinch Rolls 40HP Motor Adjustable Hump Table Mechanical Shear Belt Conveyor with Positive Stop Device Air Gate Sheet Stacker, with Two Section of Gravity Rolls

Category: 107 sheet metal working / Cutting-To-Length Lines
Latest update: 15.11.2023 add to watchlist
approved
dealer
item-No.: 158765970

used

check Seller: MAchine MW
Location: Land-us

add to watchlist

60″ x .625″ x 100,000Lb McKay Slitting Line Make: McKay Material Thickness: .065″ – .625″ Maximum Material Width: 66″ Weight Capacity: 100,000Lb Coil ID: 24″ – 30″ Exit ID: 30″ Coil OD: 90″ Maximum Speed: 450 fpm Direction: L-R Pit Type Entry Coil Car Double Mandrel Uncoiler with Hold-Down Roll Hydraulic Peeler Driven Pinch Rolls Coil Flattener with 200HP Drive Slitting Head with 16″ Arbor Diameter 250HP Drive Knives & Tooling Two (2) Scrap Choppers Recoiler with Over-Arm Separator 250HP DC Drive Exit Pit Type Coil Car Electrics, Hydraulics Controls, Tooling

Category: 107 sheet metal working / Cutting-To-Length Lines
Latest update: 15.11.2023 add to watchlist
approved
dealer
item-No.: 159022448

used

check Seller: MAchine MW
Location: Land-us

add to watchlist

60″ x .080″ x 30,000Lb Iowa Precision / Herr Voss Multi Blanking Line Make: Iowa Precision Material Width: 12″ – 60″ Material Thickness: .010″ – .080″ Coil Weight: 30,000Lb Coil ID: 20″ Coil OD: 72″ Direction: Left to Right Entry Coil Car V-shape Floor Standing Design Powered Lift & Traverse Mandrel Uncoiler 3-Leaf Mandrel Design Powered Expansion Powered Hold – Down Roll Electrical Drive Panel Hydraulic Peeling Table Adjustable Edge Guides Driven Pinch Rolls Adjustable Coil Braking Rolls Herr – Voss 4-Hi Precision Leveler Work Roll Diameter: 1.50″ Work Roll Width: 74″ Number of Work Rolls: 19 Adjustable Work Rolls Up & Down Back Up Flights Variable Speed Motor and Gear Box Electrical Drive / Control Panel Slitter / Shear Make: Iowa Precision Model: Slear 3 Entry and Exit Pinch Rolls Slitting Head with Knives Hydraulic Flying ...

Category: 107 sheet metal working / Cutting-To-Length Lines
Latest update: 15.11.2023 add to watchlist
approved
dealer
item-No.: 159113602

used

check Seller: MAchine MW
Location: Land-it

add to watchlist

Cut to length line Redman 2000mm x 13mm x 20 ton Make: Redman (UK) Material Width: 600mm – 2000mm Material Thickness: 6mm – 13mm Coil Weight: 20 ton Coil ID: 460mm – 760mm Coil OD: 1800mm Max Speed: 20 meters per minute Production Mode: Stop / Start Direction: R-L Entry V-Type Coil Car Double Mandrel Uncoiler Hold-Down Roll Hydraulic Peeling Table Driven Pinch Rolls Pinch Rolls Diameter: 330mm Corrective 4-Hi Leveler Nine (9) Working Rolls Work Rolls Diameter: 140mm Hydraulic Work Rolls Adjustment Up and Down Back Up Flights 120HP DC Motor Drive Mechanical Shear with Motor Belt Conveyor with Measuring Head Drop Type Stacker with End Conveyors Electrics, Hydraulics, Controls

Category: 107 sheet metal working / Cutting-To-Length Lines
Latest update: 15.11.2023 add to watchlist
approved
dealer
item-No.: 159131738

used

check Seller: MAchine MW
Location: Land-it

add to watchlist

Multi Blanking Line Iowa Precision 72″ x 14g x 20,000Lb Make: Iowa – Precision Model: Slear – 2 Condition: Very Good Material Width: 12″ – 72″ Material Thickness: .008″ – .080″ Coil Weight: 20,000Lb Coil ID: 20″ Coil OD: 72″ Speed: 150 feet per minute Entry V-Type Coil Car Mandrel Uncoiler Powered Over-Arm Separator Entry Table Driven Pinch Rolls Adjustable Edge Guides Slitting Head with Tooling Blade Position Indicator 6-Roll Coil Straightener Adjustable Work Rolls Flying Shear Controls with Operator Panel Electrics, Hydraulics, Controls, No Stacker

Category: 107 sheet metal working / Cutting-To-Length Lines
Latest update: 15.11.2023 add to watchlist
approved
dealer
item-No.: 159373183

used

check Seller: MAchine MW
Location: Land-es

add to watchlist

Cut to length line LDM Spotti 1500x6x25t (two levelers, flying shear) LDM CUT TO LENGTH LINE 1500X6 YEAR OF CONSTRUCTION 2000 TYPE 1500X6 THICKNESS 0.5 mm – 6.0 mm WIDTH 390 mm – 1500 mm SPEED 30 m/min UNCOILER CAPACITY 25 ton SHEET’S LENGTH 490 mm – 8400 mm DIMENSIONS 44 m X 9 m (LXW) UNCOILER: 1. DOUBLE CONE WITH EXPATION 2. I.D. = • Φ508 & Φ610 & Φ760 • Φ680 & Φ700 & Φ780 WITH O RINGS 3. O.D.= • MAX = 2000 mm • MIN = 1100 mm COIL CAR: MAX LIFTING CAPACITY = 25 Mton COIL OPENER & PRE-LEVELER: 1. 2.00 mm – 6.0 mm 2. MAX WIDTH = 1500 mm 3. 5+1 LEVELING ROLLERS Φ130 4. 52 KW DC MOTOR 1 ST LEVELER: 7. 0.50 mm – 2.5 mm 8. 390 mm – 1500 mm 9. 280 N/mm2 – 480 N/mm2 10. 19 ROLLS Φ43 mm 11. 7 + 7 BACK UP ROLLS 12.44.3 KW DC MOTOR FLYING SHEAR: 1. 0.50 mm – 6.0 mm 2. 1500 mm CONVEYOR BELT: 1. LENGTH 6000 mm 2. WIDTH 1600 MM STA ...

Category: 107 sheet metal working / Cutting-To-Length Lines
Latest update: 04.10.2023 add to watchlist
approved
dealer
ankerimg
item-No.: 159728908
New in: 1995

used

check Seller: HEGO Blechverarbeitungsmaschinen GmbH
Location: 76467 Bietigheim Land-de

add to watchlist

Bandwidth.......................... 1,500 mm Band thickness..................... 0.7 - 4.0 mm Coil weight................... 20 to. Velocity................ 14 m/min. Working direction right/left

Category: 107 sheet metal working / Cutting-To-Length Lines
Latest update: 22.02.2024 add to watchlist
approved
dealer
item-No.: 160003812

used

check Seller: TechModus LT
Location: 09133 Vilniaus Land-de

add to watchlist

Pivatic perforating and bendingline Line is manufactured 1999 and it has worked very well for us 20 years. Line is bending line with perforation unit and single press unit 35 tn. In line is separate punching unit so you can perforate material and cut it to separate ballet. Also you can use separate press toll in line. This press unit we have not used, because we other presses. FORSTNER coil cradle Weingarten Decoiler Dimeco Coil feeding line decoiler - straightener feeder Automatic Flexible punching and rollforming line for C and sigma profiles with centralized adjustment”, from Dimeco (Spain), installed/commissioned in 2019 Dimeco Coil feeding line PIVATIC coil punching line FIMI Slit Coil Decoiler and reel winder tunçman Extrusion - Single screw extruder LEMO INTERMAT Thermoforming - Automatic Roll-Fed Machine Uhlmann Blister machine Accela-Cota 170 l Tablet c ...

Category: 107 sheet metal working / Cutting-To-Length Lines
Latest update: 15.11.2023 add to watchlist
approved
dealer
item-No.: 160209199

used

check Seller: MAchine MW
Location: Land-us

add to watchlist

Fagor cut-to-length high speed line 72'' x 0.135'' x 60,000Lb is machine for cut to length coil metal cutting into metal sheets of required sizes. This machine can be used by coil metal working companies to make preparatory works before main operation. Machine is equipped with feeding unit and acceptance table to make all the process maximum automatic. It allows to make high speed cutting about 200-250 meters per minute. Cutting speed depends on metal thickness you work with, kind of metal, maximum metal cutting width. This machine helps to make preparatory works maximum fast and automatic, saving your time and labor, reduce expenses costs. Machine is equipped with flying shear so help you to save factory space avoiding loop system installation. 72″ x .135″ x 60,000Lb Fagor CTL Line Make: Fagor Year: 2003 Material Width: 12″ – 72″ Material Thickness: .020″ – .13 ...

You didn't find your wanted machine? send wanted inquiry to all dealers (no registration necessary)
Banner ad information  
RESALE used machinery 25 years online