used MENZEL Inspection machines

Working width: 3200mm, with circumferential unwinding, fettling box, accumulator, inspection table, fettling box and circumferential rewinding.

Roll width: 2600mm, controls: SIEMENS SIMATIC HMI, machine was overhauled in 2015.

Working width: 2200mm, with spare parts.

Capacity: 50.000 bt. / h Currently equipped for 0.25l Vichy / 0.25l Gastro / 0.50l GdB / 0.70l GdB / 0.75l GdB / 0.75l Benelux / 0.75l Gastro Bottles. • Inspection of the mouth sealing surface • Inspection of the side wall (both sides) • Inspection of the thread • Detection of conductive residual liquids • Detection of residual liquids by IR • Diversion of faulty bottles • Diversion of bottles exceeding height and/or width as well as lying bottles Incl. module for detection of impact spots Incl. blower for removal of water drops

Used Heuft Empty Bottle Inspector InLine IXs reflexx Device No. 2ZG044698 Condition: very good, ready for use at short notice ·       Commissioning 6 May 2012 ·       Upgrade for later integration of additional ground control using X-ray technology ·       Tape control Heuft Synchronous TX ·       Network Heuft Hlan ·       Haylofts two ways discharge with div. Heuft container transport Convejor ·       Troubleshooting Software Wizard ·       Software assistant guided instructions for the different container changes ·       Power max. 46,000 fl./h ·       5 Variety licenses incl. scope of delivery: ·       Belt control Spectrum TX ·       Measuring bridges for inlet control and discharges incl. height connections ·       2 x Discharge Delta K  ...

Used Heuft Glass Empty Bottle Inspector InLine reflexx Device No. 2ZG042943 Condition: very good, ready for use at short notice ·       Original delivery date 12.2011 ·       Power max. 46,000 fl./h ·       Pass direction from left to right ·       Two triggers ·       Secomak blower instead of compressed air ·       Transponder detection for RFID test bottles ·       Discharge monitoring ·       Network Heuft Hlan (Upgrade Optional) ·       Hayt two ways discharge Delta K to the right ·       4 Variety Licenses ·       Tripartite Delta K for band height of 1130 ·       Two fluids for lye detection Not available! ·       inlet control, must be supplemented if necessary ·       Thread edging, must be supplemented if required ·       The documentation is complet ...

PET Empty Bottle Inspector HEUFT InLine TI 60 BFS2-r Device No. 2SG021663 Built: / year of construction: 2006 Output[B/h]: / performance [cont./h]: 36,000 Flow direction of: / moving direction from: Direction: / rejection direction: Installation location: / installation site: In front of the filler • Basic unit: Empty bottle inspector • Inspection: 1.Soil-IN-r • Inspection: Estuary IN-r • Inspection: 1st sidewall IN-r • Inspection: 2nd sidewall IN-r • Inspection: SW double resolution-r • Inspection: Carrying ring/PET-r • Inspection: RefPet abrasion-r • Inspection: RefPet Ventslot-r • Inspection: Stress crack detection-r • Accessories Transport belt: Height adjustable • Residual fluid detection: IR • Height adjustment: for discharge • Cross-adjustment: for discharge • Discharge ...

BOSCH Type KLD 1041 Leak Test Machine for Ampoules and Vials Leak test machine for glass containers. Linear automatic machine for the inspection of ampoules, injection cylinders/cartridges and injection bottles/vials, which checks each container at four inspection points by means of high-voltage technology. The testing principle is based on the detection of the changing impedance of a container filled with an electrically conducting liquid. The containers are examined for: hairline fissures and pinholes ; insufficient glass wall thickness/tip domes too thin ; capillary pores ; leaking fusion points, sealing points and ampoule neck tips ; absence of fill. MAIN FEATURES: It is recommended to carry out the container leaktightness test directly after sterilization or fusing. The unit is equipped with: conveyor system, infeed belt, 4 high-voltage inspection stations (1-2 check bodies and ...

Krones EBI empty bottle Inspector along with contour detection module and ejector tables Krones bottle inspector along with contour detection module: • Type: Krones Linatronic • Production year: 2012 • Capacity: 60 000 bottle/hours • Work direction: form left to right Possible detections: • Rest of the liquid (infrared) • Double control of residual soda (high frequency) • Neck damage control • Sidewall control modules • Damaged bottles discard • Separate rejection of dirty bottles • Detection of the contour of the bottle • Detection of the color of bottle • Separate rejection of a bottle with wrong contour or color The system includes: • KRONES Linatronic Inspector • Contour detection module • Ejection table behind the Inspctor • Ejection table behind the contour detection module

An inspection system for bottle label control is offered, Throughput 30,000 Fl/h With 3 Kamaras and control

Inspector, Fabr. Nail, Type: NAG, Type: Full inspection 5/8, up to 5,000 fl/h, furnished on 0.33 lt BV-Maurer + 1.0 lt bracket, KK 0.33 lt Gourmet, KK 0.5 lt NRW + EURO, running direction re->li for floor, muzzle, sidewall and lye control with new card for side control serviced annually

The detection is set up on 0.5l glass bottles in the 20 module box. The inspector is equipped with a multi-camera system. As soon as a foreign bottle is detected in the box, it is then discharged via a pusher. Currently is set to cross travel. The detection is adjusted for 0,5l glass bottles and twenty modul crates. The inspector comes with a multi camera system. If an external bottle is detected, the crate will be pushed out in an other line. Currently the set up is for a long side leeding crate.

Blower for water droplet removal in front of inspection machines

1 CALATOR inspection machine for open width knitted fabrics type BSM 2500, roller width 270 cm, working width 250 cm, entry small roll, exit small roll, with LABELTEX 86 type LBTX defect registration unit, with illuminated table

Seidenader T&T Single Unit Track & Trace System for marking and verification of folding boxes/cartons for serialisation and aggregation (Track&Trace), the product codes and variable data (serial no., batch no., expiry date, datamatrix codes, French codes, etc.) printed on the folding cartons are verified via a camera for accuracy and quality, including Wolke m600 advanced Ink jet printer using HP ink cartridges (height of printing max. 12.7 mm), 1 (one) printing station with 2 (two) printing heads located on the back side, infeed conveyor with a length of approx. 300 mm and a width of approx. 185 mm, transfer unit with lower belt and adjustable upper belt for precise and reliable product transfer, carton length (in the direction of travel) max. 220 mm, carton width max. 200 mm, direction of travel from left to right, handheld scanner, electrics 230V + N + PE /50 Hz/1,0 kW, machine floor  ...

Brevetti ATM 15 duplex (2 x modules) automatic inspection machine for syringes, currently set for 10.85mm diameter syringes (long and short needle), output up to 133/minute per module (266 per minute total). Each module is fitted with 6 control stations for presence of bung, reflective particles, fill height and bung position, needle cover, non-reflective particles, plus turbidity meter. Each module has 3 reject channels plus pass. One module is ATM15 SX year 2008, the second is ATM15 DX year 2007. Both units operate from one control panel.

Fully automatic inspection machine for dry sterile products in vials. Capacity: up to 300 units / min. Format parts: vial diameter: 16.25 and 22 mm. PLC: Alan Bradley. incl. separate control cabinet (dim: 2400 x 600 x 2000 mm, weight ca. 500 kg) and further accessories.

RAIL LENGTH: 5 - 60 M, CONTINUOUS MEASURING, 6 LASER MEASURING HEADS, SPEED: 1 M/SEC., MODERNISED IN 1992

ULTRASONIC INSPECTION - TESTQMATIC - TYPE: SPA-2N, L=5-60 M, 1 M/SEC., 1988 EDDY CURRENT INSPECTION - MPA - 1989 RAIL PROFIL MEASURING DEVICE - SCHMITZ & SÖHNE AND BSB - 1989 PRODUCT HEIGHT: 95-165 MM, HARDWARE & SOFTWARE

Stratec / Bull fill level inspection. Suitable for liquids wihout foam. User manual incluted Pusher incluted.

Full automatic video inspection and packaging system for plastic caps. Different sizes. Include elevators, hopper ZALKIN, two camera video inspection COGNEX, packaging system.

Capacity: 1,500 K/h Types of boxes: Boxes of 6, 0.7 VdF, 200 x 300 x 320 mm, transverse Boxes of 6, 1.0 VdF, 200 x 300 x 320 mm, transverse Boxes of 12, 0.7 VdF, 355 x 270 x 310 mm, longitudinal running Boxes of 24, 0.2 goiter neck KK, 300 x 400 x 210 mm, longitudinal run Boxes of 24, 0.2 goiter neck SV, 300 x 400 x 210 mm, longitudinal run The following evaluations are integrated: crate geometry, foreign bodies, crate color, bottle height, bottle color + Box pusher VT-1201 Year of construction: 2016 Capacity: 1,500 K/h Box types: Boxes of 6, 0.7 VdF, 200 x 300 x 320 mm, cross run 6-boxes, 1.0 VdF, 200 x 300 x 320 mm, cross run Boxes of 12, 0.7 VdF, 355 x 270 x 310 mm, lengthwise run 24-boxes, 0.2 Kropfhals KK, 300 x 400 x 210 mm, longitudinal barrel 24-boxes, 0.2 goitre neck SV, 300 x 400 x 210 mm, longitudinal run The following evaluations are integrated: crate geo ...

This Qualicaps inspection machine combines computer image processing technique and CCD line sensor camera to capsule rectification-transfer mechanism. The appearance of the capsule is inspected by direct image capture with the camera, controlling its orientation and rotating the capsule during intermittent transfer. The machine controls filled hard capsules directly on the line by meticulous examination of pharmaceutical or nutraceutical products. It allows accurate inspection of capsule appearance performed by color line sensor cameras with the possible immediate expulsion from the production line through an appropriate rejection system, when the machine detect itself anomalies on the product. Technical data: Dimensions mm 2000 x 700 x 2450 Total weight Kg 1000 Voltage Volt 400 Frequency Hz 50 Production characteristics: Capacity 50,000 capsules/hour Compatible capsules: ...

Ultrasonic measuring and testing unit suitable for pipes up to 200 mm in diameter Manufacturer: ConPro Type: DMCON 200 Built: 2008

Ampoule Inspection Machine 2006 EISAI AIM 288. Format parts: 1,2,5 and 10 ml. ampoules;