used LESCUYER Extruders

Nakata Zoki Kobe, Japan (Troester design) Duplex Extruder Unit Dual 150mm dia PIN Type Extruders, Year of manufacture: 1990, with Roller Feed, and duplex Die. L/D ratio 16:1 Number of Pins: 10 Rows x 8 Pieces, Spare Pins included. Screw Speed 45 r.p.m. Motors 185kw D.C. variable speed, 415 volt, 3ph, 50hz. Full Books and Drawings available. Thyristor Drives included. Starter and Control Panel for Lower Extruder only. Die usable Width 18\\, In good condition.

Troester.200mm H/F strainer M/C Number 7175-71 L/D 6.5/1 Roller Feed 350mm. Hinged strainer head with hydraulic clamp. 125KW AC v/s motor. On single bedplate. With controls.

Barwell C3 Preformer Extruder 2500 psi Output 600kg/hour Ram type Extruder Extruder size 250mm With Rotary Cutter 8 fixed speeds Year 1980

Manufacturer: Paul Troester Maschinenfabrik/Hannover Year of construction: 1978, machine was in operation until the end of 2015 Screw diameter: 150 mm Length: 16 D (approx. 2,400 mm) Screw speed: 2.5-25 / 4 - 40 U/Min. Centre height of the extruder: 1,100 mm Type of gearbox 3 TH 990 K / 2s, 2 speeds. Gear ratio: = i1 16.5: 1 i2 = 26.4: 1 Maximum gearbox output torque: 45,000 nm Maximum permissible injection pressure: 350 bar without limitation through the extrusion head. The extruder will be overhauled and designed/changed according to customer's specification. Below pictures 1-4 show an extruder overhauled by us.

1 x Buss PR200? Ko-Kneader, supplied fully refurbished by Buss in 1995, G130 gearbox, 11 L/D ratio, with 340kW dc motor and controls. Including oil heater and TCU 2t/hr output. Spare screw and barrel segments.

According to the description below

8" Cold Feed Rubber Extruder

We´re offereing successfully since many years twin-screw compounding extruders >> NEW segmented screws and cylinders, LD ratio due to your request Side-feeders, vacuum ports and accessories Please contact us for further information

1 x Berstorff GmbH 250mm strainer extruder, Year of manufacture: 1988, L/D ratio 7:1, power roller feed (300mm wide), with 120kW, 1800rpm DC variable speed motor mounted on top of gearbox (belt drive), with tube head and knife at top for sheet extrusion. Complete with control panel etc and in very good condition.

Key data: 100 , 140

Stock No.2452 1 used, partially overhauled and functionally tested pelletizing line Throughput up to 500 kg/h depending on the material, consisting of: Tamping unit Kreyenborg SW 100, drive 7.5 kW Extruder BKG single screw Ø 100 mm – 35 LD, Drive 132 kW – AC frequency controlled Screw speed up to 143 rpm.-1 screw depth 14 mm Heating capacity approx. 35 kW installed 1x athm. Degassing zone Screen-pack-changer Double piston Kreyenborg K-SWE 160 RS back-flush self-cleaning with screen surface 244 cm² BKG underwater pelletizer AH 300, complete with: Start-up valve incl. Hydraulic station Granulator with drive 4 kW Water pump 2.2 kW By-pass system, water tank with heating 9 kW installed and heat exchanger BKG granulate centrifuge TWE 300 with drive 3 kW pellet classifier table Control board and Siemens material feed conveying, big-bag filling station � ...

Iddon HRX 4.5? (120mm) Cold Feed Rubber Extruder Year 1994 LD ratio 17:1 Bostock & Bramley Gearbox ABB Motor: 1994, 95kW, 1870 rpm, 419 amps, 360 volts With 1 x spare vacuum screw With Control Panel

Material: PE, PP, PS, ABS / Details: DC motor 220 kW, degassing, dcrunner, screw diameter 70 mm, LD: 32, Throughput: approx. 400 - 600 KG/hr.

PE 300 plastic recycling and regranulation line was built in China in 2011 by Zhangjiagang Wuhe Machinery Co. LTD. The extruder for plastics used in the processing and manufacturing of various types of materials can produce up to 300 kg of parts in one hour of operation. The complete PE and PP plastic extrusion line includes a compactor, screw, cylinder, conveying system, heating system and temperature control panel. Material production begins by heating the plastic to a maximum temperature of 300°C in the 11 heating zones of the PE 300 granulating line, controlled by thermoregulators. The extruder then presses the material further through a 100 mm diameter screw located in a cylinder with abrasion and rust protection. At the end of the process, the machine head moulds the plastic to give it the right properties and shape. The PE 300 extruder is equipped with thermoregulators with ...

Used twin-screw, parallel, counter-rotating extruder by Amut model BA92 NOMAX. New 2011. Output: 270 - 370 kg/h Hours of operation: 53638 h Other details: - Diameter of augers 92 mm - L/D ratio 28:1 - Drive power 60 kW (400V, 50 Hz, 3 ph) AC - Two sets of screws -for ABS processing -for PVC processing - Number of cylinder heating zones 7 - Number of cylinder cooling zones (air) 4 - Number of heating zones for head and adaptor 5 + 1 - Built-in pressure and temperature measurement system for plastic mass - Thermal oil unit for thermostating the worms for PVC - Drive power of vacuum degassing pump 11 kW - Drive power of screw feeder 1.5 kW - Without control (subassemblies available according to the list)

New and unused machine Berstorff twin screw extruder ZE 130A Extruder screws: 2x140 mm L/D 30:1 Built: 1988 (unused) Drive: DC motor - 250 kW Screw rotations: 300 rpm Extruder heating: 70 kW 2x Degassing complete screw in original packaging 2 machines available Location Germany, Wuppertal Visit possible, appointment by appointment

Strainer Bandera 150mm with 75kW motor. This machine has been overhauled by Deguma and little used after that. More info as attachment.

available Troester Triplex Extruder Top machine QSM 90x 16D Middle machine 200W x 6D Below machine QSM 150 x 16D Head MW500 Description attached!

Description Single Screw Extruder Screw diamter 60 L/D 25 Motor power 27,5 k

Description Conical Twin Screw Extruder Screws Diameter 45 - 97 Screws Length 390 Barrel zones 3 Nr.1 vent Thermoregulated screws Motor power 15,4 kW Forced feed

Description Conical Twin Screw Extruder Conical screw diamter 50 - 104,6 Screw length 1000 Motor power 29,6 kW nr. 4 Cylinder zones nr.1 vent Forced feed Working hours 54910

Description Conical Twin Screw Extruder screw diameter 80 Thermoregulated screws 1 vent Motor power 68 kW

Single-screw rubber extruder with feed roller and degassing in screws of 70mm and a process length of 22.D - with two-speed temperature-controlled entagling screw - Degassing cylinder with device for static and/or vacuum degassing of the material - a vacuum block pump - two water temperature control units with 9kW heating capacity each, - a Siemens SPS S7 machine with Siemens KTP1200 HMI control panel - a directly driven feed roller feeder for rubber raw strips, a funnel-material stiffening system with Strip monitoring - temperable base body for tool holder and v.m

Farrel Twin Screw / Rollerdie Extruder complete available with Motor and Inverter Description attached!

Barwell MR400 Top Load Ram Extruder

Multiple extruders