We use cookies to optimize our website for you and to be able to continuously improve it. By continuing to browse the site you are agreeing to our use of cookies.
Disagree
used
X - axis: 3000 mm Y - axis: 1500 mm CNC Brand: _Unknown / Other CNC Model: KAR CNC Make Koike Aronson Type MONOGRAPH - Millenium Year 2010 KAR - CNC X = 3.000 Y = 1.500 Hypertherm 100 AMP POWERMAX* Dust collector * DXF conversion * Cutting up to 16 mm
used
CNC Gantry Plasma Cutting Machine Manufacturer: Koike Type: Deltatec 3000 Year of construction: 2019 CNC Control: Katana 1 plasma torch with power source Kjellberg HiFocus 161i neo with automatic gas console 1 oxy-fuel torch Extraction table: size 2x6 m Track length: 9 m Laser Pointer for Plate Layer Detection Filtration system Cutting software SigmNest
used
Equipped with Kioke type Hybrid 200 control, Hypertherm type HT2000 refrigeration unit, Hypertherm torch height controller and guide beams L approximately 9mtr. Suitable for 6mtr plate. Required installation space lxw approximately 925x500cm. Please note! The buyer is responsible for loading.
used
CNC Plasma Auto Bevel machine KOIKE VERSAGRPH-6000 3DP (2014) Width 4500 mm x 43 M, thickness 6-40 mm; "Plasma""I""cutting: 6 to 40mm; ""V""cutting: 9to 30mm; Power supply 3-phase 440V; Fluid oxygen 7~9.9 kg/cm; Fuel gas 1~1.5kg/cm (LPG); Air 7~9.9 kg/cm"; Cutting speed: 0~6,000mm/min; Marking Soeed max. 18,000 mm/min; Rapid speed:24,000mm/min (2014) Cutting bed dim: 30M x 4.6M Rail Length: 30M; Span: 6M With Chiller, Power Supply, Panel box, Cable rail, compressed air dryer, dust collector and Transformer Rails and cutting bed Attached to rails and cutting bed of Lot 313 Make KOIKE Serial VG-A-0218 Model VG-6000DXI Year 2014
Amperage range maximum: 0 A Amperage range minimum: 0 A Table Length: 1.220mm Table Width: 1.220mm Table load on 50 mm: 5.000Kg Table load on 200 mm:4.545Kg Table load on 400 mm:3.500Kg Table load on 600 mm:2.900Kg Table load on 1000 mm:1.850Kg Rotation table: 360000° Length: 2.000 mm Width: 1.600 mm Height: 1.800 mm Weight: 2.000 kg
used
CNC Portal Cutting Machine Manufacturer: ESAB Type: Suprarex SXE-P1 4000 Built: 2009 CNC Control: Vision55 2 autogenous burners 1 plasma burner with power source Kjellberg HiFocus 160i Track width: 4,000 mm Working width: 2,500 mm Track length 18 m (shortenable) without table without filter
used
CNC-Portal Cutting Machine Manufacturer: Sato Type: Satronik D5765 Built: 2016 CNC control: Satocontrol CNC 3010 Track width: 5,750 mm 6 x oxyfuel torche without a career without table without filter
used
CNC portal flame cutting machine Manufacturer: MGM Type: Cortina DS3100 Retrofit 2022 CNC control: MS300 Track width: 3,100 mm 1 oxy-fuel burner gas type as desired Track length: 5 or 6 m without table
used
CNC Portal Flame Cutting Machine Manufacturer: Messer Type: Easytherm 4600 Year of construction: 2006 Control: Global Control Working area: 3 x 9 m No table!! Table can be offered on request! Running track: 12 m with HEB beam 1 oxy-fuel burner ALFA 1 plasma torch with power source Kjellberg 160i plus Incl. marking Filter system Torit
used
Flame separating machine Manufacturer: Kjellberg
used
CNC Portal Flame Cutting Machine Manufacturer: Zinser Type: 2115 Year of construction: 1999 CNC control: CNC500 2 oxy-fuel burners Working area: 2x4 m Filter system at call
used
CNC gantry flame cutting machine Manafacture: Zinser Type: 3825 Year of construction: 1998 CNC control: CNC2010 Working area: 3000 x 6000 mm 2 oxyacetylene burners no table
THIS LINE IS USING FOR ALUMINIUM PROFILES IN PRODUCTION OF WINDOWS, DOORS CURTAIN WALLS ETC. POWER: 60 KW, PLC MITSUBISHI, MAX. WORKING WIDTH: 6.5 M, ALU THICKNESS: 0.2-0.25 MM, STRIP WIDTH: 120 - 230 MM, COIL WEIGHT: 360 KG
used
Thermal store / buffertank with a nominal capacity of 40,000 litres on 2 steel bases. Contents: approx. 40 m³ / 40,000 litres Material: steel Diameter with insulation: 2.75 m Diameter without insulation: approx. 2,50 m Year built: approx 2007 Buffer in cylindrical shape. Insulated by mineral/glass fibres, 10cm thick. Panels are made of aluminium sheets. The container is in used state, and has been drained and cleaned professionally. The heat storage tank has a separate connection pair (forward / reverse) for the heat supply (E.g. from CHP, boiler) and heat extraction (e.g. from a heating network). Thus, a real buffering is possible, and a temporary extraction higher than the thermal power of the heat generator, eg. to deal with heat peaks. Optionally and at additional cost more pairs of connection can be installed to connect another heat generator to this buffer. Flanges ...
used
Wire rod: 0.1 - 1.3 mm section area: 5 - 70 mm power: max. 400 rpm complete with cooling unit and driven wire reel; good
new
THERMISCHE REINIGUNG PYROLYSE-OFEN Zykluszeit : 2 - 4 Stunden Beschickung : Wagen, manuelle Beschickung Isolierung : Keramikwolle + Steinwolle Dicke der Isolierung : 175 mm Höchsttemperatur : 1.260˚C Heizungsart : Direkt beheizt Heizquelle: Erdgas, Flüssiggas oder Diesel Brennkammern : 2 Sätze Überhitzungskontrolle : Wassersprühdüsen - 2 Stück Sicherheitskontrolle : Wassersprühdüsen - 2 Stück Backofen-Sicherheitstür : 1 Satz Schaltschrank : PLC-gesteuert, Schaltgeräte der Marke Schneider Electric Steuerungssystem : Bedienfeld mit Touchscreen und Softwaresystem MATERIAL Ofengehäuse : Stahlkonstruktion und Blech, spritzlackiert 1. Brennkammer: Schamottestein und feuerfester Zement, 1.400˚C 2. Brennkammer: Schamottestein und feuerfester Zement, 1.260˚C BETRIEBSTEMPERATUR 1. Brennkammer: 250 - 600˚C 2. Brennkammer: 800 - 1.100˚C Durchmesser ...
used
used
Thermal CTP Manufacturer: Heidelberg Model: Suprasetter A 52 Year: 2008 max. platesize: 670 x 525 mm with RIP Further details on request Price: on request
used
Fully automatic Thermal CTP exposure Heidelberg Suprasetter A 52; good condition; suitable for thermal printing plates; Meter reading 107.00 plates; Workflow Meta RIP and ZIP 3 output; integrated Auto Top Loader; Punch 425mm Autoplate; Suction for ablative printing plates; Transfer bridge; Washout G+J C 85; Printing plate forklift Grafoteam PST 26. Full automatic thermal plate setter Heidelberg Suprasetter A 52; good condition; used for thermal printing plates; counter only 107,000 plates; workflow Meta RIP with ZIP 3; auto plate loading system; punch 425mm autoplate; debris removal system; bridge; washing unit G+J C 85; plate stacker Grafoteam PST 26.
used
4 up Thermal CTP Manufacturer: Agfa Model: Avalon N4 10S Year: 2012 Platesetter Architecture: external drum Laser technology: 830mm infrared thermal Light source: 32-channel infrared laser diodes Image area: Maximum 830mm x 633mm (front margin 15mm, rear margin 12mm) Resolutions: 1200-2400dpi Plate Sizes: Maximum plate: 830mm x 660mm Minimum plate: 324mm x 370mm (standard) 304mm x 370mm (optional) Thickness: 0.15mm to 0.3mm AGFA ELANTRIX 95SX Processor Plate width min-max: 200x950mm Plate length min: 300mm Plate thickness min-max: 0.15-0.4mm Procesing speed: 10-160cm/min Throughput: 58pl/hr(portrait 745x605mm) 44pl/hr(portrait 1030x790mm) Tank content, developer: 57l Tank content, wash: 40l AGFA ELANTRIX ST95EX PLATE STACKER Price: on request
used
Floor dimensions: 3,000 mm x 22,000 mm ; complete mesh tape; Baking area: 132 m²; Temperature regulation: separate for upper and lower level; Temperature zones: 2; incl. jacks front and rear; incl. loading conveyor: 4 x 3 m (LxW); Boiler: KO 500; Power: 465kW; permissible operating overpressure: 10 bar; permissible operating temperature: 300°C; incl. 2 thermal oil boilers; Dismantled
used
8 up Thermal CTP Model: Screen 8600 (Topsetter 102) 64 diodes Year: 2004 with Loader AT-T 8001 Year: 2001 Stacker Plate Counter: 316,000 Price: on request
used
4 up Thermal CTP Heidelberg Topsetter P74 Year of production: 2003 (first installed in May 2004) Bridge between CTP and developer Developer Agfa Azura C95, year of production: 2015 Automatic stacker for plates Computer with SignaStation Computer with RIP MetaDimension Actual Running Time: 7609h Exposure Time: 4536h Plate winding cycles: 115454 Price on request
used
Thermal CTP Platesetter Manufacturer: Heidelberger/Creo Model: Trendsetter 3230 Laser new, 440 hours year: approx. 1997 Location: germany Price: on request
used
There is one KV-2,5/25 and one KV 1,6-2/25 available, power machine 1/ 2: 2907/ 1745kW, year of construction machine 1/ 2: 1988/ 1979, there is also a chimney available.