used KIEFEL Extruders

Technical details material.: OPS, APET, PP, HIPS, ABS Forming area (VxH): 520 x 400 mms Depth of draw: 120 mms of material thickness (max.): 1.50 mms of technical details heating, moulding and cutting. This machine has the BFS system which allows to cut in place in the forming station Forming area: 520 x 400 mms of Max sheet width: 590 mms No of cycles are very much depending on the product. However we have been producing more different products with up 50 cycles by minute, but they were no deeper than 40 mms. All movements are 140 mms with a recommended max. depth/hight of 120 mms We have been producing OPS, APET, PP, HIPS and ABS on the machine. The read few years mainly HIPS and APET The thicknest material we have been producing, were 2.0 mms HIPS, but I wants recommend more than 1.5 mms HIPS.

Drive power: 110kW, with reversing Film Take-Off Kirion T 1300, Monoblow Head Kirion 120/300-1, further accessories and documentation.

Connected load: 104kVA, operational hours counter: 18,775h, the chain of the chain rail system was replaced in 2018.

Thermoforming Machine Brand: Kiefel, model: 76/225F. It shapes and cuts by vacuum pieces from rolls of PPE that are previously heated in the oven. Everything goes online, fully automatic and includes all empty aurxiliars, refrigeration, mold change trolleys, etc. Forming area: 760x2250 mm max, workpiece height: 220 mm pos. max, 30 mm neg. max, upper cutting force: 30 KN, lower cutting force: 30 KN, sheet line: 1575 mm, vacuum: 500 m 3/h, cycle time: ca. 20 sec (material dependence), glue type: butyl or hot melt glue, glue application speed: mx. 400 mm/sec (depending on the contour and type of glue), applicator head control: amount of glue depending on speed, tool change time: less 5 min, measures: 25500x6000x4600 mm.

DESCRIPTION KIEFEL Model: KL 1 SH 52 BFS + KVH 83 Preheating Model type Nr.34.322-08.35, Identity.Nr. 100-035, Tp-No. 157/93 Year of construction - 1993 Forming Area: 540x420mm Film Width: 570mm Foil thickness: min 0.2mm - max.3mm Depth of draw positive / negative : 140mm / 140mm Materials: PET, PVC, PP, PS, HIPS Condition - in use, in production Location: Bucharest, Romania, 050192 Other details: - Number of stations : 5 - Preheating, Forming, cutting in mold, punching, stocking. Preheating for PP foil, model KVH 83, 2050/2200 / 2550mm, Length 2950mm, Width 1400mm, Weight 700Kg, max 150 Celsius degrees - the documentation in original (5 books) + scanned (PDF files) - a lot of spare parts - we have the software saved - working pressure: 6 bar - voltage: 3x400V + N + PE, 50Hz - dry cycle strocke / min ...

Automatic Roll-Fed Kiefel KMV 50D machine Year: 2002 Maximum forming area: 500 x 350 mm Minimum forming area: 300 x 100 mm Max tool dimensions: 516 x 366 mm Forming height above - below Material: 120/40 mm Suitable materials: PS, OPS, EPS, PP, PE, PVC, APET, CPET, RPET Maximum sheet width: 545 mm A / B stacker Pressures Max. Max. 2.5 bar Cycles / min: 35 Approx. Length: 10,300mm Approx width: 2100 mm Approx.Height: 2200mm Weight: 6700 kg Machine in production

Nakata Zoki Kobe, Japan (Troester design) Duplex Extruder Unit Dual 150mm dia PIN Type Extruders, Year of manufacture: 1990, with Roller Feed, and duplex Die. L/D ratio 16:1 Number of Pins: 10 Rows x 8 Pieces, Spare Pins included. Screw Speed 45 r.p.m. Motors 185kw D.C. variable speed, 415 volt, 3ph, 50hz. Full Books and Drawings available. Thyristor Drives included. Starter and Control Panel for Lower Extruder only. Die usable Width 18\\, In good condition.

Troester.200mm H/F strainer M/C Number 7175-71 L/D 6.5/1 Roller Feed 350mm. Hinged strainer head with hydraulic clamp. 125KW AC v/s motor. On single bedplate. With controls.

Barwell C3 Preformer Extruder 2500 psi Output 600kg/hour Ram type Extruder Extruder size 250mm With Rotary Cutter 8 fixed speeds Year 1980

Manufacturer: Paul Troester Maschinenfabrik/Hannover Year of construction: 1978, machine was in operation until the end of 2015 Screw diameter: 150 mm Length: 16 D (approx. 2,400 mm) Screw speed: 2.5-25 / 4 - 40 U/Min. Centre height of the extruder: 1,100 mm Type of gearbox 3 TH 990 K / 2s, 2 speeds. Gear ratio: = i1 16.5: 1 i2 = 26.4: 1 Maximum gearbox output torque: 45,000 nm Maximum permissible injection pressure: 350 bar without limitation through the extrusion head. The extruder will be overhauled and designed/changed according to customer's specification. Below pictures 1-4 show an extruder overhauled by us.

1 x Buss PR200? Ko-Kneader, supplied fully refurbished by Buss in 1995, G130 gearbox, 11 L/D ratio, with 340kW dc motor and controls. Including oil heater and TCU 2t/hr output. Spare screw and barrel segments.

According to the description below

8" Cold Feed Rubber Extruder

We´re offereing successfully since many years twin-screw compounding extruders >> NEW segmented screws and cylinders, LD ratio due to your request Side-feeders, vacuum ports and accessories Please contact us for further information

1 x Berstorff GmbH 250mm strainer extruder, Year of manufacture: 1988, L/D ratio 7:1, power roller feed (300mm wide), with 120kW, 1800rpm DC variable speed motor mounted on top of gearbox (belt drive), with tube head and knife at top for sheet extrusion. Complete with control panel etc and in very good condition.

Key data: 100 , 140

Stock No.2452 1 used, partially overhauled and functionally tested pelletizing line Throughput up to 500 kg/h depending on the material, consisting of: Tamping unit Kreyenborg SW 100, drive 7.5 kW Extruder BKG single screw Ø 100 mm – 35 LD, Drive 132 kW – AC frequency controlled Screw speed up to 143 rpm.-1 screw depth 14 mm Heating capacity approx. 35 kW installed 1x athm. Degassing zone Screen-pack-changer Double piston Kreyenborg K-SWE 160 RS back-flush self-cleaning with screen surface 244 cm² BKG underwater pelletizer AH 300, complete with: Start-up valve incl. Hydraulic station Granulator with drive 4 kW Water pump 2.2 kW By-pass system, water tank with heating 9 kW installed and heat exchanger BKG granulate centrifuge TWE 300 with drive 3 kW pellet classifier table Control board and Siemens material feed conveying, big-bag filling station � ...

Iddon HRX 4.5? (120mm) Cold Feed Rubber Extruder Year 1994 LD ratio 17:1 Bostock & Bramley Gearbox ABB Motor: 1994, 95kW, 1870 rpm, 419 amps, 360 volts With 1 x spare vacuum screw With Control Panel

Material: PE, PP, PS, ABS / Details: DC motor 220 kW, degassing, dcrunner, screw diameter 70 mm, LD: 32, Throughput: approx. 400 - 600 KG/hr.

PE 300 plastic recycling and regranulation line was built in China in 2011 by Zhangjiagang Wuhe Machinery Co. LTD. The extruder for plastics used in the processing and manufacturing of various types of materials can produce up to 300 kg of parts in one hour of operation. The complete PE and PP plastic extrusion line includes a compactor, screw, cylinder, conveying system, heating system and temperature control panel. Material production begins by heating the plastic to a maximum temperature of 300°C in the 11 heating zones of the PE 300 granulating line, controlled by thermoregulators. The extruder then presses the material further through a 100 mm diameter screw located in a cylinder with abrasion and rust protection. At the end of the process, the machine head moulds the plastic to give it the right properties and shape. The PE 300 extruder is equipped with thermoregulators with ...

Used twin-screw, parallel, counter-rotating extruder by Amut model BA92 NOMAX. New 2011. Output: 270 - 370 kg/h Hours of operation: 53638 h Other details: - Diameter of augers 92 mm - L/D ratio 28:1 - Drive power 60 kW (400V, 50 Hz, 3 ph) AC - Two sets of screws -for ABS processing -for PVC processing - Number of cylinder heating zones 7 - Number of cylinder cooling zones (air) 4 - Number of heating zones for head and adaptor 5 + 1 - Built-in pressure and temperature measurement system for plastic mass - Thermal oil unit for thermostating the worms for PVC - Drive power of vacuum degassing pump 11 kW - Drive power of screw feeder 1.5 kW - Without control (subassemblies available according to the list)

New and unused machine Berstorff twin screw extruder ZE 130A Extruder screws: 2x140 mm L/D 30:1 Built: 1988 (unused) Drive: DC motor - 250 kW Screw rotations: 300 rpm Extruder heating: 70 kW 2x Degassing complete screw in original packaging 2 machines available Location Germany, Wuppertal Visit possible, appointment by appointment

Strainer Bandera 150mm with 75kW motor. This machine has been overhauled by Deguma and little used after that. More info as attachment.

available Troester Triplex Extruder Top machine QSM 90x 16D Middle machine 200W x 6D Below machine QSM 150 x 16D Head MW500 Description attached!

Screw diameter: 59mm, screw rotational speed: 25-250/min, with complete documentation, control cabinet, screen changer, side dosing unit, granulator and additional accessories.

Description Single Screw Extruder Screw diamter 60 L/D 25 Motor power 27,5 k