We use cookies to optimize our website for you and to be able to continuously improve it. By continuing to browse the site you are agreeing to our use of cookies.
Disagree
used
sheet width: 2100 mm plate thickness: 20 mm pre-bending: . diameter of upper rolls: 300 mm diameter of lower rolls: 400 mm total power requirement: kW weight of the machine ca.: t dimensions of the machine ca.: m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
used
sheet width: 4000 mm plate thickness: 40,00 mm pre-bending: total power requirement: kW weight of the machine ca.: 78 t dimensions of the machine ca.: m Adjustable rollers 3 The rollers are adjusted hydraulically Top roller diameter 710 mm Bottom roller diameter 640 mm Side roller diameter 520 mm Working speed 2+4 m/min (up to 8m/min) Additional equipment Electronic synchronization Air-cooled oil cooler Upper support device Lateral cylinder support device (10t) Infeed table (20t) hydr. Bladder storage Cone bending device The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
used
sheet width: 4000 mm plate thickness: 40,00 mm pre-bending: total power requirement: kW weight of the machine ca.: 78 t dimensions of the machine ca.: m Adjustable rollers 3 The rollers are adjusted hydraulically Top roller diameter 710 mm Bottom roller diameter 640 mm Side roller diameter 520 mm Working speed 2+4 m/min (up to 8m/min) Additional equipment Electronic synchronization Air-cooled oil cooler Upper support device Lateral cylinder support device (10t) Infeed table (20t) hydr. Bladder storage Cone bending device The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
used
Bending semi-automatic, tube bending machine, mandrel bending machine MOBITEC type BAH 1-2 KOTTMANN und BERGER GmbH Fabr. No. 056 Year of manufacture 09/2004 - for simultaneous bending of two steel pipe sections up to 12 mm bending angle max. 90 Tube diameter max 12mm Mandrel length approx. 65 mm Nominal power 3.5 kW Compressed air max. 6 bar / approx. 1 litre per bending cycle Mains connection 400 volts, 50 Hz - Pneumatic clamping - Pneumatic mandrel retraction - Control for angle input via STOBER Controlbox Series 4000/5000 - Control SIEMENS S7-200 with display TD200 - Machine without bending tools and without tool bearing bolt 25 x 183 mm - only 1 bending mandrel available (see pictures). Space requirements L x W x H 1000 x 1000 x 1500 mm Weight 390 kg good condition; used
used
Timing belt pulley, for taper bushing, 9 pieces PAGUS 2x PL26 8M 20 profile: 8M, 26 teeth belt width: 20 mm head circle: Ø 64,84 mm Taper socket: 1108 3x PL32 8M 20 profile: 8M, 32 teeth belt width: 20 mm head circle: Ø 80.16 mm taper bushing: 1610 1x PL38 14M 85 profile: 14m, 38 teeth belt width: 85 mm head circle: Ø 16.66 mm taper socket: 3020 Material: Steel New ! Dimensions ( packaging ): 200 x 200 x 140 mm
used
Hollow chamber gasket profile, window profile, push-in SAINT-GOBIAN SIPRO® profile: P1476-724 Length: approx. 55 m Profile width: 26 mm Profile height: 27 mm Material: high-viscosity silicone rubber New ! Dimensions ( packaging ): 600 x 600 x 250 mm
used
Bearing number: 3488 Profile steel shears Manufacturer: Mubea, Type: KBLH 500 Machines NR.: 0156085927332, Year of construction: 0 Specifications: Size Printl 50 To Max punching dia 30 x 15 mm mm Stroke length 0-60 mm Number of strokes per min. 16 Extension 410 mm Flat steel 180 x 20 - 400 x 10 mm Angular steel 50 mm Round steel 55 mm Total power 7.5 kW Hydraulic. Length: 1400 mm, Height: 1800 mm, Width: 800 mm, Weight: 1800 kg
used
Profiel bending machine Auerbach K80 Shaft diameter 80-100-80mm Hydraulic adjustment Digital position display With:Set of steel rollers of 60mm Plastic Rolls± .30-46-65-76mm Various discs and punching rings
used
Profile bending roll hydraulic Sertom PP Output shafts size 180 mm -pre-tensioning brackets between the 3 rolls Traction tooling to bend HEB / IPE on the hard side -Lower rolls driven motorized -Top roll hydraulic pinch- bending Beivhd0xri -Top roll size 600 mm -Side rolls size 520 mm Adjustable rolls to seat and bend the different size of profiles -MAX. CAPACITY -Angle 180 mm leg-in/out- -iron bar on edge 170 mm- -Iron bar on flat 350 mm- T section 160 mm- -Pipe 8,5” inch - -Beams HEA300 - INP360- Weight of the machine 15 Ton -SIDE ARMS OPERATED IN 3 DIRECTIONS WITH DOUBLE ROLLERS- -OIL RESERVOIR WITH COOLING UNIT – -CONSOLE WITH DIGITAL BENDING POSITION AND PROGRAMMABLE READOUTS -MACHINE CLEANED AND GREASED –CONTROLLED AND TESTED UNDER POWER FULLY WORKING
used
Profile bending machine hydraulic heavy duty -output shafts 360 mm Equipped with traction tooling for H-beam HEB IPE INP rolling on the hard-side Configuration -pyramid dual pinch side rolls independent hydraulic -3 rolls driven hydraulic and gear unit -synchro. -set of rolls for HEB beam – INP beam - flat bar square bar. -Set of heads for traction the HEB – INP beam bending on the hard side -Set of rolls for pipe bending. Pipe 20 inches max capacity. -Lateral correctors left/right side hydraulic operated in 3 directions -Add-on rollers angle bending & T-section leg-in / leg-out -Control panel console electric joysticks manual use & program automatic -Digital readout screen display 8 axis position reading of the rolls - 8 axis automatic programmable bending works -Electric Vac 400/50 ( rewirable on request ) -weight total of the machine approx. 65 Ton ...
used
Stock number: 3774 PROFILE BENDING MACHINE Manufacturer: KUMLA - ROUNDO, Type: Z-30 Machine NO.: 5017, Year of construction: 1990 Specifications: Wave dia. 110/90 mm Round steel 60 mm Flat steel 200 x 30 Special roll mm Stainless steel upright 100 x 20 mm Angle steel 90 x 90 x 9 mm Speed 7.5 m/min Square steel 55 x 55 mm Total power 4 kW Hydraulic. 3-reels. Horizontal/Vertical Accessories: Digital Various matrices. Length: 1250 mm, Height: 1550 mm, Width: 1100 mm, Weight: 2100 kg
used
Key data: 80 mm, 80 mm, 80 mm
Profile bending roll shafts output 80 mm brand Sergi Italy model PP type SER80CI year 2001 machine reversible can work with vertical shafts/horizontal shafts electric power 10Hp on the hydraulic centralized unit voltage 380 /50 -output shafts 80 mm -rollers diameter 250 mm -rollers interchangeable in 3 pieces each shaft to seat and copy the different shape of profiles -Powered driven the 3 shafts dragging with hydraulic motor and planetary gear-unit -Dual rolling speed fast/slow. -Rollers gap adjustable with front head screw modern system. -Pinching pyramid configuration each shaft individual move hydraulic. -Lateral correctors / straighteners left and right side with double contrast rollers. -Centralized control panel movable on wheels with all electric commands. -Digital position readout with position memory setting of the pinching rollers -Safety devices in com ...
used
Key data: 200 mm, 300 mm, 200 mm
Profile bending roll used equipment hydraulic model AR200 year 2008 make MG Italy Capacity bending chart photo in enclosed -Technical data: Output shafts size 200 mm -Machine complete with set of rollers adjustable for the various shape of profiles. -Traction tool hydraulic operated for the HEB-beam - IPE - UNP bending the hard side. -Lateral correctors left and right side hydraulic operated in 3 direction. -Included additional set of rolls for pipe 6" inches -Machine with 3 rolls driven system with individual hydraulic motor and axial gear-unit on each shaft. -The 3 shafts working on bearings, heavy duty type with sealed lubrication. -Centralized control panel movable on wheels with all electric commands. -Dual rolling speed up to 5 mtr/min with automatic balancing system between the 3 rolls. -Safety devices in compliance with European regulation. CE mark. - ...
used
profile bending roll model Femar PF22 year 1985 machine in working condition refurbished mechanical operated motorized electric pinch roll pyramid mechanical operated gear unit motorized electric rolls rotation position bending readout gauge adjustable rollers height to seat and bend the different shape of profiles Capacity ( see chart in enclosed ) angle 120 x13 mm flat bar on edge 120x30 mm flat iron 140x45 mm square iron bar 70 x70 mm T-section 100 mm C-section 160 mm IPE beam 160 mm dimension 2170 x1650 x H 1200 mm 8 ton
used
Technical data approx.: -Mot. Driven Upper Roller -Manual. Infeed of the middle roller - Both lower rollers can be adjusted horizontally - Shaft diameter approx. 60 mm - Effective shaft length approx. 120 mm - Working speed in one stage - Bending capacity approx. : - - L. and T – iron outside at R 1200 mm 70 x 7 mm - - L – Iron Inner R 1200 mm 75 x 10 mm - - Flat bar flat R 450 mm 100 x 15 mm - - Flat bar upright R 700 mm 60 x 10 mm - - Square bar R 450 mm 30 x 30 mm - - Tubes with special tool R 900 mm 50 x 5 mm -with: - Standard bending roller set - Drive 400 V / 3 kW - Weight approx. 1200 kg - Space requirement approx. W 900 x H 1500 x D 1200 mm
new
The profile bending machines of the KPB series combine high bending performance with modern mechanical engineering and powerful hydraulics. They can bend medium and heavy steel profiles with great precision. A high drive power as well as the hydraulically adjustable bending rollers make the entire profile bending machine series a high-performance solution for metal construction, locksmithing and general mechanical engineering. These machines are also used in the production of roofing, greenhouse construction, advertising technology and the furniture industry. - Shafts Ø 50 / 40 mm - Rollers Ø 152 / 162 mm - Bending speed 3.3 m/min - All 3 reels driven - Hardened rollers and shafts - Hydraulic roller infeed - Horizontal and vertical machining possible If you are interested, we will be happy to send you our complete data sheet.
new
CNC – controlled profile and tube bending machine for demanding and precise bending work with hollow sections and tubes. With our machines, aluminium – steel / stainless steel – various plastics such as PVC window profiles (depending on the application) can be bent with repeatable accuracy, regardless of the material. Depending on the equipment, our machines can also be used for three-dimensional bending work. Our REPANDUS models can work both horizontally and vertically. The models of the REPANDUS series work with a fixed upper roller and two movable lower rollers – this means that the straight end piece is relatively short compared to machine concepts with fixed lower rollers. The machine body is made of vibration-absorbing cast steel Shaft diameter of upper and lower rollers Ø 70 mm Shafts made of special steel – hardened and ground Bending force 190 kN Maximu ...
used
Akyapak APK 240 Profile Pipe Bending Machine Tools are included Machine is in good working condition
used
Akyapak 38 3D Tube and Profile Bending Machine 16,25 and 30 mm tools are included
used
Machine will be sold with all tools from 32 mm to 63 mm Mandrel lenght : 2500 mm
used
Davi Profile Bending Machine Machine is in good condition year 2015
used
Sahinler HPK-200 Profile Bending Machine Machine is in excellent condition Roll diameter : 200 mm Working speed : 2-5 mm Engine power : 30 KW
used
Model 2050 Power Hp 30 Serial number 20701 Made in Italy Central shaft 150 mm, 2 lateral shaft 120 mm
used
Bending machine and core extractor. Guaranteed excellent condition and operation, also different types of rollers and cores. year 1994
used
Akyapak APK 61 Profile Bending Machine Machine is in good condition