used HAAS RECYCLING Hammer mills

Plastics Recycling Extruder PP=900-1000kg Complete Line

Ermafa twin screw extruder B 2.95-35 D 1992/1995 -Extruration plant for recycling -with hot-tee, Filter -Drying centrifuge, -Degassing plant, -storage silo, -discharge silo, -Chain elevator. -900-1000 kg/h PP

Ermafa Type: RA 1200-350 , Agglomerator Control: Siemens S6 Built: 1995 Dimensions and weights Dimensions LxWxH m: 1.5 x 1.5 x 3.36 Machine Weight Kg: 4250 Other Motor-Three-phase cage rotor motor Performance-355 KW Speed-1488 rpm Voltage-380/660 V;50 Hz Degree of protection-IP 55 Type-IM V3 Mode-S 6 Mixed fraction from shredding 700-1100 kg

Ballshaping- and Delaminationmill Molinator for fine delamination! Diverse Types: RW VKR16/3 / 22-37kW and RW VKR 22/3 / 75-110kW Input Composite Material Examples: Regrind from hair-wire, printed circuit boards, electronic circuits, other composited material. Al / Plastic, Cu / Plastic, Cu / Glass fibre, ABS / Plastic fibres, etc. Type choice: depending on the material / depending on layer thickness / depending on test‘s / according to the desired throughput. Description Molinator: In the inner acts very high forces (High acceleration / high relative-speed)! Bigger parts will be delaminated. Composite-material separates at the phase of boundaries. Metals will be ballshaped. Plastics depending on the specifications stays “fluffy” or will be grinded. These effects besides the desired delamination, are helpfully for the separation and are exactly coordinated to our s ...

Zig Zag Air Sifter Sizes/ wides from 200mm - 1800mm Precondition for the separation are differences in the material like: - Different sizes of particles - Differences of the density - Differences in the surface condition of the particle - Differences in the form of the particle - Grain size 0.1mm – 40mm, (bigger particles are possible with a special design) We are the manufacturers of these plants and we build Zig Zag Sifter Plants in different sizes. In order to make you a definite offer we need to know some points: 1. What material you want to separate? 2. Grain-size of the material? 3. Bulk weight kg/liter of your material. 4. We have technical center at our house, where we can test your material.

3 Shaft shredder with HARDOX spirals (approx. 500x1700mm), complete hydraulic system with Brevini gearboxes, new base frame with new steel construction, new hopper 6 cbm, inlet-opening: approx. 1100x1700mm, in addition: 7 reserve spirals available

To separate and sort after the specific weight from light and heavy fraction. Useable for grain, aluminium/plastic, rubber/textile, cable-recycling, etc. Type and size are choiceable, depending on the product and throughput. At constant machine length, it is possible to choose between working width from: 450mm, 600mm, 900mm.

To sieve dry material: like flour-, grainy-, and granule-shaped material. Free running sieve case hanging in a massive framework With an automatic sieve ball cleaning. Sieve-layers in a simple way interchangeably. Applicable to sieve all floury-, grainy materials in dry condition. Sizes of Wide 500 – 1500mm / Lengths 1200 – 2400mm Sieve layers 2 to 4 layers, grain

Demo machine from demonstration pool Enormously versatile cable slot machine thanks to individually adjustable, standing cutting knives. Cables are cut as standard by two knives penetrating the insulation on the side. The series was significantly improved in terms of safety in 2014 and now features a short feeder for thin cables and a long feeder for thick cables. The change is made in seconds by means of a rotary mechanism. The simplicity in the construction and the construction with two powerful, synchronously running rollers is left. With coarse gearing, even thicker cables are safely fed into the knives and transported further after the cutting process for removal. Blunt knives can be easily and cost-effectively sharpened with a standard grinding machine.

CANDY RECYCLING AD 2000 made in 2015 for recycling of Rework from hard candy production suitable also for jelly, toffee, lollies, fondant even wrapped products result after recycling: completely transparent and neutral sugar-glucose syrup-water solution consisting of: dissolving machine intermediate/buffer tank, volume 2000 L with platform horizontal rotary drum vacuum filter unit year 2015 very good condition

Slow-running robust single-shaft shredder Suitable for the pre-shredding of various materials without solid stuttering materials. Application: Crushing of industrial and commercial materials, films, packaging materials, textiles, paper, rubber, demolition wood, pallets, paper rolls, cable drums, mixed plastics for thermal and recyclable recycling, loose or pressed into bales. Lindner Jupiter 3200 Drive power: 2x 160 kW (Schorch motors) Sieve perforation: Sieving 148 mm Control cabinet: complete with ( FUe -P-Drive) Opening: 3190 x 1750 mm Single volume: approx. 8 m3 Rotor length: 3190 mm Rotor flight circle: 745 mm Rotor speed: 50Hz : 58 rpm Number of rotor blades: 36 pieces Knife dimension, pointed knife: 145x 145 x 47 mm Geggenmesser unten: 9 pieces Scraper comb above: 9 pieces Hydraulic feed: 11 kW Weight: approx. 38 t Dimensions LxWxH mm: 6250 x 3260 x 3090(H=4900 m ...

The JMC 407 is the top seller among our alligator scissors. It is cost-effective, has a sufficient knife length and enough power for most tasks in metal recycling. It is suitable for cutting many materials, such as profiles, pipelines, motors, transmission housings. The scissors are also frequently used for cleaning scrap metals or for cutting vehicle coolers. The machine has a control without electronics and a manually adjustable holder, which also acts as a protective hood. The scissors can be used by foot pedal in single or continuous operation. The opening width is adjustment via simple clamping screws.

Small shredder for various tasks such as old cables, plastics wood, etc. With hydraulic, electronically controlled feed. Drive 18.5 + 2.2 kW (rotor + feed). Rotor shaft with connectors for connecting a cooling device (e.g. when used for NYM old cables. The machine is 1 year old and little used from our demo machine inventory. The machine is offered with a one-year used machine warranty.

Small vibrating sieve with two decks for three fractions. The diameter of the sieve inserts is 400 mm. This includes a bet with balls that keep the screen insert clean from below. This is suitable, for example, for the screening/classification/quality assurance of copper granules (contamination by plastics or aluminium are sifted) or for the re-treatment of plastic granules from the cable recycling. The sieve is located in our demo pool and is little needed.

Heavy peeling machine from also for thick cables up to approx. 110 mm diameter. Cable stripping machine for PVC and lightly reinforced cables. Easy adjustment of the knives by handwheel. Cables are cut from both sides at the same time, so that the remittation drops slightly. Knife individually adjustable by spindle for different strength swelling. Double spindle for precise adjustment of the cable thickness. Two separate 1.5 kW motors for a lot of power when pulling through the cables

The IRS 120 Easy is the perfect entry point into cable recycling. The special combination of large flywheels and multi-part segment cutting knives makes it possible to efficiently recycle old cables made of copper or aluminium even without high power consumption and without shredding. The machine impresses with its small footprint, is easy to maintain and easy to use. Compared to most of the competition's systems, the machine has two separate fans for separator air and dust removal. This eliminates the usual interactions between more or less clogged filters and the purity of the copper granules. In addition, the separator air is not roughly adjusted via throttle valves, but by sensitive adjustment of the fan speed. This gives you the best qualities in finished copper. This machine is an immediately available storage machine and has 4 screen inserts, electronic pre-equipment for ...

Small shredder for a wide range of tasks such as old cables, plastics wood, etc. With hydraulic, electronically controlled feed. Drive 18.5 + 2.2 kW (rotor + feed). The machine was overhauled by the manufacturer ISVE in September 2020 and supplemented with an electronics for networking into a cable recycling line. A rotor cover for the optimized processing of old cables has also been added. Currently, the shredder has a 16 mm hole sieve but other hole diameters can also be added. With the 16 mm hole sieve, the shredder reaches about 250 kg/hour when processing mixing cables.

Lindner Mircromat 2500 HP, 160 kW, with direct drive. Control cabinet with frequency converter. Knife size 43 x 43 x 19.5 mm (carbide). Number of blades 131. Max rotor speed 265 rpm With large filling shaft (5.6 cbm) and filling hood. Internal pusher 7.5 kW. Perforated sieve 30 mm. New machine

make: Ambra output: 75% mehr Zuzug des Mittel : alle Medien : Ölbinder Recyling-Pack The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Small floor filter, which can be used, for example, for extracted air from separators in cable recycling. The filter is without its own fan, so it works purely passively. The filter and the collection bags have a diameter of 500 mm.

Compact but powerful machine for processing old cables up to approx. 25 mm in diameter. The nominal output of the system is 120 kg/hour when using a 4.0 mm perforated screen. By using a pre-shredder, the performance can be significantly increased, then stronger cables are also possible. The machine has been checked and modified in our workshop. - new dividing table - new set of knives - new sieves - new seals - Connection for refrigeration unit - Connection for feed and conveyor belt On request, we can supply additional accessories for the machine, such as: - Pre-shredder -Magnetic drum - Dosing accumulator - Refrigeration unit - Dust filter - Screening drum - Bigbag stand with air conveyance for plastic granules

Used cable recycling plant Tecnoecology T 250 Turbo Year of construction: 2008 The plant consists of the following parts: - Pre-shredder: Bano MAC 630, approx. 250 - 400 kg/hour, depending on material - Conveyor belt to the dosing accumulator, approx. 4.0 m - Dosing accumulator with discharge conveyor, approx. 1.5 m³ - Controlled conveyor belt with belt magnet for feeding the granulator, approx. 4.0 m - Granulator GA 400/30, approx. 250 - 400 kg/hour, depending on material - Turbine mill, T 25-2, built in 2019 - Separator TV 300, inverter controlled, separation table 80 μm - Dust extraction and filter system The entire system currently achieves between 200 and 300 kg/hour in operation, depending on the cable composition. On request, additional components, such as a big bag loading for the plastic or the re-screening of the granules, can be supplied. The plant is curre ...

Cable recycling plant with many innovations in all plant components for up to 600 kg/hour (depending on material) The basis of this recycling plant is modularly constructed from strong and innovative individual components. In the standard version, the following structure is obtained. - Preshredder MR 4080 or MR 40-100 - Conveyor belt with magnetic separator - controlled by PLC - Granulator C 600 with axle length 600 mm, 5 rotor blades and 37 kW drive, cooling of the housing by unit against adhesions - Z-separator for the separation of heavy copper or 1 granulate - Dosing drum for the optimally uniform feeding of the following turbine mill - Ghibli 545 turbine mill (new model), optionally with coolable housing and inverter control - SA 600 separation table, new version with PLC inverter control of the air volume + eccentric drive with inverter control of the oscillation + adju ...

Very good machine from our demonstration pool. Few hours of operation or signs of use. The peeling machine is suitable for XLPE cables, underground cables, cables with steel armouring, cables with aluminium and lead armouring, but also for processing PVC and rubber cables. With this machine, two cuts can be made at the same time in one operation, so that the processing can be twice as fast as with other models. Technical data: Working range/cable diameter: 30 mm to 150 mm Pulling speed: max. 12 m/min Motor: 2x 3.0 kW - 400 volts Dimensions (LxWxH): 1.8 x 1.0 x 1.2 m Weight: approx. 660 kg

Used conveyor belt, built in 2020, few operating hours Very heavy design for recycling With very strong neodymium magnet in the upper deflection drum Reducing gear for slow conveying speed With concealed wavy edge and crossbars on the harness Large inlet hopper with adjustable slider for material height on the belt 4 m long, discharge height approx. 2.2 m (variable) Ideal, for example, for feeding material into a cable recycling plant At call