used H K Four sided planing machines

Industrial robot Manufacturer: Kuka Type: KR30-3 Year of construction: 2011 Reach: 2033 mm Weight: 665 kg Payload: 30 kg Kuka Control KRC4 Weight: 150 kg Software V8.3.40 Kuka Touch Panel Kuka Interconnectors

Industrial robot Manufacturer: Kuka Type: KR16-2 Year of construction 2014/2015 Reach: 1611 mm Weight: 235 kg Payload: 16 kg Kuka Control KRC4 Year of construction 2015 Weight: 145 kg Software version V8.3.40 Kuka Touch Panel Kuka Interconnectors

Four-sided planer copper mill Type: Vuin 605 Planing width 605 mm Planing thickness 3 – 200 mm in the horizontal area Planing thickness at the rear in the vertical area 80 mm Upper and lower planer shafts as 4-knife shafts 4 planer shafts 1. Bottom 5.5 kW 2. Top 7.5 kW 3. Left 4 kW 4. Right 4 kW Shortest piece length, self-continuing: 350 mm Electrically height-adjustable table Width adjustment for the rear planer heads manually via crank 2 feed speeds Suction nozzle diameter 3x120mm, 1x150mm Weight approx. 2700 kg Space requirement L 2350 x W 1400 x H 1800 mm Control cabinet 1200 mm x 420 mm x H 1050 mm

CATALOG NO. 7223 TECHNICAL DATA - max planing width 770mm - max planing height on both sides 200mm - maximum planing height on four sides 100mm in advance: - pulling, toothed input shaft - pawls - 2 rows of pressure - pulling shaft, toothed - pressure - planing shaft 770mm, 4-knife 7.5kW - pressure - pulling, smooth, output shaft from down: - guide strip - introduction table with a divided sliding shaft - introductory tabletop adjustable up/down - planing shaft 770mm, 4-knife 5.5kW - 2 smooth, pulling, adjustable shafts in the back: - 2 side spindles + clamps 1) vertical right 100mm 4kW 2) vertical left 100mm 4kW - spindle diameter 35mm - spindles adjustable up/down, right/left - electric setting of planing thickness - 4 types of feed speeds 6;9;12.5;18 m/min - 2kW feed motor - diameters of the exhaust pipe: 2x120mm, 2x180mm - dimensions length/width/heigh ...

CATALOG NO. 7186 TECHNICAL DATA - max planing width 510mm - max planing height on both sides 170mm - maximum planing height on four sides 100mm *in advance: - pulling, toothed input shaft - pawls - pulling shaft, toothed - pressure - planing shaft 510mm, 4-knife (2 knives installed) 4kW - pulling, smooth, output shaft *from down: - guide strip - sliding roller – adjustable top with an up/down roller - planing shaft 510mm, 2-knife 4kW - 2 smooth, sliding, adjustable shafts *in the back: - 2 side spindles + pressure - 1) vertical right 100mm 2.35kW - 2) vertical left 100mm 2.35kW - spindle diameter 35mm - spindles adjustable up/down, right/left - manual setting of planing thickness - 4 types of feed speeds - feed motor 1.5kW - dimensions length/width/height 1940x1320x1140mm - weight 1330kg ADVANTAGES – ideal for processing logs, floor tiles, etc. –  ...

KUPFERMUHLE four-sided planer with additional table, multi-saw 600x200mm - after technical inspection - German production - DOUBLE-SIDED PLANING HEIGHT 200 mm - ideal for wet wood - electric height adjustment - double feed chain - additional preliminary table with a 340 mm head - additional material feed systems TECHNICAL PARAMETERS: planing width 600 mm cutting height on both sides planing height on four sides 200 mm 100mm power of vertical spindle motors 2 x 5.5 kW lower shaft motor power 7.5 kW upper shaft motor power 11 kW engine power of the first head 4 kW multi-saw engine power 15 kW adjustable vertical heads four upper pulling rollers three lower pulling rollers two receiving pull rollers 4 knives per shaft, shaft diameter 145mm six types of feed speeds 7 / 9 / 11.5 / 14 / 18 / 23 m/min 2 rows of anti-kickback pawls spindle diameter 40 mm disc  ...

KUPFERMUHLE four-sided planer with additional table, multi-saw 600x200mm - after technical inspection - German production - DOUBLE-SIDED PLANING HEIGHT 200 mm - ideal for wet wood - electric height adjustment - double feed chain - additional preliminary table with a 340 mm head - additional material feed systems TECHNICAL PARAMETERS: planing width 600 mm cutting height on both sides planing height on four sides 200 mm 100mm power of vertical spindle motors 2 x 5.5 kW lower shaft motor power 7.5 kW upper shaft motor power 11 kW engine power of the first head 4 kW multi-saw engine power 15 kW adjustable vertical heads four upper pulling rollers three lower pulling rollers two receiving pull rollers 4 knives per shaft, shaft diameter 145mm six types of feed speeds 7 / 9 / 11.5 / 14 / 18 / 23 m/min 2 rows of anti-kickback pawls spindle diameter 40 mm disc  ...

Multi-side processing machine, multi-edge automatic lathe KEKEISEN type Tornomat 2 Multi-edge impact lathe for 4-edge and 6-edge machining, square automatic lathe Masch. No. 668 361 Year of construction approx. 1975 Workpiece diameter max. 35 mm Working range 6-edge: max. SW 32 mm Working range 4-edge: max. SW 24 mm Spindle speed 250, 355 , 450 rpm. Mains connection 380 Volt, 50 Hz - equipped with 3 fold knife head for hexagonal hydraulic feed movement 0.1 to 0.5 mm/rev - Hydro-mechanical collet clamping- Workpiece clamping diameter in the built-in collet 10 mm- Control cabinet adjacent (L x W x H 700 x 350 x 1300 mm) Space requirement automatic lathe L x W x H 1250 x 850 x 1250 mm Space requirement on pallet L x W x H 1650 x 850 x 1300 mm Weight 1.4 ton. good condition; used

vert. Internal broaching machine maximum tractive force: 10T Max stroke: 1000 mm Max cutting speed: 10.9 m / min Max reverse speed: 27.5 m / min Clamping surface: 400 x 400 mm Room set: 3 piece

Planer-saw combination copper mill DK-14 Year of construction 1982 Working width 605 mm Working height 200 mm Number of spindles 3 Shaft arrangement Hobewelle bottom+top / Saw shaft bottom Spindle speed 6000 rpm Motor power 5.5 - 7.5 - 30 kW Feed speeds 7 - 23 m/min Feed motor 2.2 / 3 kW Driven rollers in table 3 Feed rollers top 4 Yt9k30 Transport rollers in extract 2 Tool head horizontal dia. 126mm, L=610mm Chip removal below 12 mm Chip removal top 20 mm Suction nozzle diameter 140-140-120 mm Weight 3500 kg Space requirement 1500 x 1900 x 1500 mm Voltage / Frequency 380V 50Hz 3Ph Cutting height saw max.: 50mm Saw blade diameter max.: 250mm

Key data: 500 mm, 2800 mm, 4 St.

Technical details: - Max. planing width: 500 mm - Maximum chip depth: 5 mm - Length of feed table: 1,300 mm - Length of the take-off table: 1,500 mm - Total length of the table: 2,800 mm - Table height: 800 mm - Max. workpiece length without support: approx. 1.5 m - Length of the joining fence (Aigner joining fence with integrated auxiliary fence): 1,300 mm - Height of the joining stop: 150 mm - Joining stop adjustable up to 45° and extendable over the entire width of the table - Diameter of the TERSA knife shaft: 125 mm - Nominal speed of the TERSA knife shaft: 5,000 rpm - Number of planer blades: 4 pieces - Minimum width of planer blades: 17 mm - Diameter of suction nozzle: 160 mm - Required air velocity: min. 20m/s - Required air volume: 1500 m³/h - Vacuum at 20m/s air velocity: 705 Pa - 6 x machine shoes with adjustment screws - incl. EMERGENCY STOP switch En ...

Inv. Num. : 7406 Type: RISZ 16 Producer: ARTHUR KLINK Created: 1993 Parameters: Theoretical diameter of the tool: 95 mm Max. workpiece height: 300 mm Clamping surface: 400x400 mm Maximum working stroke: 1250 mm Maximum stretching force: 16 t Weight: 6900 kg

Koelle edge planing machine model FKF 51 is in good condition, ready to use. L x W x H = 3000 mm x 700 mm x 950 mm Weight approx. 200 kg Built in 1982 Engine No. 390 The rubber rings at the pressure rollers should be times replaced. Subject to changes, errors, prior sale! Service/spare parts by MATEC CH-4900 Langenthal/DE-79618 Rheinfelden MATEC system + technik GmbH Mechanical engineering Eisenbahnstrasse 25 CH-4900 Langenthal/Switzerland Tel. 0041 62 966 18 32 Fax 0041 62 966 21 12

Planing shaft DOMA 2300 bottom and top Knife shaft DOMA 2300 Right and Limks

-Knife shaft Z4 -in chrome-plated finish -D 200 mm -for machine K133 Condition good, used

Planer and multi-leaf saw, ideal for batten production. 2 planing shafts above and below with 5 knives per shaft. Planing height 200 mm Planing width 600 mm. Engines: Bottom 18.5 KW. Above 18.5 KW. Electric table adjustment. Feed up to 23 m /min. Attached multi-leaf saw Raimann DK 14. Cutting width 407 mm. Cutting height 50 mm. Motor 37 KW. Setback fuses and fluted feed rollers with pressure. Feed unit on the inlet side.

x-travel: NA mm y-travel: NA mm workpiece height: mm stroke length max.: 450 mm table length: 450 mm table width: 350 mm total power requirement: 1,7 kW weight of the machine ca.: t dimensions of the machine ca.: m Shaper, horizontal,mechanic,vice hydraulic The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Four-side planer KUPFERMUHLE 600x200mm - after technical review - German production - PLANING HEIGHT ON TWO AND FOUR-SIDES 200 mm - ideal for wet wood - electric height adjustment - electric adjustment of the left head - double feed chain planing width 600 mm planing height on two and four sides 200 mm power of vertical spindle motors 2 x 8.6 kW motor power of the lower shaft 5.5 kW upper shaft motor power 7.5 kW guiding ruler electric height adjustment adjustable vertical heads four upper pulling rollers four lower pulling rollers two take-up pull rollers 4 knives per shaft diameter of shafts 150 mm six types of feed speed 7 / 9 / 11.5 / 14 / 18 / 23 m/min row of anti-recoil pawls spindle diameter 30 mm / 100 mm material pressure at the left head dimensions (length/width/height) 260 x 190 x 205 cm weight 3500 kg

Manufacturer: Koch, Type: SBD - 320 , Year: 1994, Control: Programm, Working widht max mm: 1500, Arbeitstiefe max mm: 320, Working thickness max mm: 10 - 32, Saw diameter mm: 350, Work piece transport: Kette, Drilling support horizontal: 2, Drill gearings: 7, Drill gearings: 7, Drill support from top: 5, Drill gearings: 7, Belt conveyor: yes, Gluing: yes, Re-charging: no, Dovel insertion: yes, Raster 32 mm: yes, Horizontal drilling from both sides: yes, Wight approx. kg: 6000, Year :1994

Manufacturer: Koch, Type: Compact, Year: 1991, Control: Programm, Working widht max mm: 150-2500, Arbeitstiefe max mm: 200, Working thickness max mm: 80, Schwenkbereich Grad in X: +30-90, Dovel units: 3, Dovel diameter mm: 10-12, Drill gearings: 2, Drill gearings: 2, Drill gearings: 2, Drill spindles per support: 5, Gluing: yes, Dovel insertion: yes, Raster 32 mm: yes, Compressed air bar: 6, Wight approx. kg: 3000, Year :1991

Edge banding installation consisting of the following elements: - feed table TB 10/10/20 - edge bander KAR 610/20/PU/S2 - panel turning station cross/longitudinal TD 51/30/12 - destacking robot KUKA KR 180-2 PA - Ligmatech return system installation specifications: workpiece dimensions length 300 - 3200 mm width 120 - 1200 mm (for dogs), 1800 mm (equal to longitudinal entry) thickness 12 - 60 mm weight max 80 kg edging material 0.4 - 2.0 mm throughput speed 25m/min robot 10 strokes /min Equipment edge bander: Infeed fence automatically adjustable anti adhesive sprayers Squaring device UF20: 2 x 4.0 KW Workpiece preheating Glue application unit PU34 6-fold edge magazine for rolls Pressure zone with 1 driven, 6 non-driven rollers, automatic adjustment End trims HL86, pneumatic adjustment phase/straight, 2 motors 0.22 kW Rough trimming: 2 x 0.55 KW Contour trimming FF12 , 4 motors 0.4 kW Pr ...

Workpiece sizes: Length 180 - 2500 mm, width 150 - 800 mm, thickness 12 - 40 mm Fixed side at the left, motorised width adjustment of the right side Working height/ transport height: 920 mm Workpiecetransport with belts, infeed belts can lift up Variable feed speed Each side has got 5 glue injectors and 8 dowel inserters (Type 34) Doweldiameter: 8 mm, dowellength 30 mm, dowelprojection 7-14 mm, dowelcenters min. 32 mm, max. 736 mm Each side with dowel hopper feed with shaker and separators Controll mirror Glue pump 1:1 Glue injection controlls type ELC

; ready

Load capacity up to 12,000 kg Grab content from 1 m 3 up to 10 m³ Make: all reputable manufacturers workshop testing 2015 Fully functional workshop overhaul and paint renewal upon request.

Size max 220 x 297 mm Speed max 2.700 c/h Equipment o automatic feeder o 2 cutting stations o 3 edge corner cutting station o delivery ; working condition