used GERMANPLAST Agglomerators

Hydraulic Gripper

MAGNETIC SEPARATORS, in form of overbelt plates,, grids, channels, stars, etc.

Goose neck shaped conveyor belt Blueprint 3.541 mm. on floor mm. 2.150 in horizontal + 1.350 mm. diagonal Angle 45° 1.166 mm discharging point Approx.450 mm working width Complete with transport paddles 1,5 kw gear motor Fitted with a 250 mm diam.magnetic drum at the end Discharging outlet on bottom for material Separate discharging outlet for extracted ferrous material, The machine is as new, 200 worked hours

QUICK WASHER for RIGID and SOFT PLASTICS, made in AISI304 stainless steel, low water consumption, can be used with hot water or mild detergents, for reground LDPE LLDPE HDPE film, rigid PE PP PVC PET PA ABS PS PC, 7,5 kw motor 400V 50/60Hz, inner auger 400 mm diam., length 3.000 mm., material and water are loaded from the bottom, material discharging is done through a draining auger from top, bearings are positioned outside the wet chamber, seals on the lower bearing to exclude any contact with water, auger speed is adjustable to change throughput rate 500 to 1.000 kg/h, throughput rate can be adjusted according to contamination and material, Low water consumption (depending on contamination), The water can be mechanically filtered with a water screening system (available separately), electric cabinet, Users manuals , drawings, CE compliance

BUFFER SILO 15.000 lt. (or 8.000 - 12.000 - or bespoke), barrel Ø 2,2 mt. - height 3.0 mt., overall height 5,23 mt, made in electro-welded carbon steel sheet, sturdy supporting structure, internal rotor with spiral and agitator arms, inspection hatch on barrel wirh safety devices, bonfiglioli gearbox, power 3 kw electric motor, transmission with elastic coupling, finish painted externally with rustproofing and enamel, CE compliance + instruction manual, installed power : 3

This is an accessory to our buffer silos range ([GE253](https://www.germanplast.eu/listings/4115680-buffer-silo-new-m achinery)) not a stand-alone unit., Mostly used to dry EPS scraps Standard configuration (customizable): 1,1 kw fan in a painted steel cage 15,3 kw heating unit size 400x300x300 mm. Metallic cell filters 500×500 mmplete with galvanized steel frame and in/out connections System of pipings 100 and 200 mm diam., curves, clamps, to convey heated air into the silo. Electropneumatic guillotine shutters in galvanized steel. temperature probe, connections. Complete with electric cabinet managing the whole system. User’s manual, drawings, CE compliance

Dries, reduces size and degasses materials in one step. For PE PP PET PS ABS PC PET PVC POLYLAMINATED, PULPER etc. Low maintenance costs No operator needed High ROI Huge output, heavy duty, made for 24/7 job 400 kw drive (260 kw in work) Italian technology and material quality standards. Output in a continuous flow The melted plastic can feed extruder directly with high energy saving, to be filtered and granulated, thus forming a complete, automatic line from scraps to granule We can provide the special extruder needed for the purpose. The line includes normally : buffer with extraction screws on supporting structure + extruder with motor, gearbox, pulpit control panel, + electric cabinet + strand matrix On separate request : cooling calander, cooling belt, conveyor belt to buffer, metal detector, square matrix with hydraulic pack (for special purposes) Post-sale assistance for spares, a ...

Fitted with a 12 mm grid N.2 outlets All parts in contact with material are on AISI304 stainless steel Classifying surface 1400×500 mm. Electric panel for start/stop Safety switches Height of granule outlet 650 mm.from floor

For extruders 500 to 1500 kg/h Supporting structure made in sturdy steel with sides made in special alloy. Group of dandy rolls to guide the streams Lower roll in cemented steel Upper, pressing roll made in nitrated steel, pneumatically lfted Asynchrone drive with inverter Cutting unit with dual cutting edge Made in anti-wear steel Electrical control panel with general switch,service switch and amperometer Adjustable speed Rotor diam. 240 mm. N.28 teeth on rotor Counter-blade length 350 mm. 2 cutting edges, 11 kw drive Include n.1 extractor, User’s manual, CE compliance

For a variety of applications : PE PP PS EPS ABS MIXED PLASTICS, RDF, ORGANIC WASTE, etc. Automatic process. No operator needed, huge output, heavy duty. Italian technology and material quality standards. Can be inspected in our premises for a few days more Construction year 2005 – used for tests only Used machine next-to-new (very few worked hours) Very versatile, can be used for a variety of applications as RDF, briquettes, wood plastic compounds or just to agglomerate moist plastics for further pelletising. Materials are subjectd to pressure and friction treatment. The friction generates heat which melts plastics and binds it to the other materials (if present). The Output is a square shaped stream 140×140 mm. (Different matrixes can be supplied) Average output from 1500 to above 2000 kg/hr, depending on material and moisture content. Average power consumption 260 kw/h – 0,12 kw/ ...

Including: Injector Hopper Pipe connection diam. 160 mm. Bends Clamps Cyclone Customized to your project

SEMI-AUTOMATIC, NON-STOP SCREENCHANGER, Screen Ø 30 to 400 mm. Can fit any type of extruders with single or twin screws Made in sturdy steel on supporting wheeled cart for easy transport Smart construction out of our long experience in plastic extrusion Complete with control panel for temperature and pressure management Hydraulic power pack Connection flanges available on given design of pelletizer and extruder Single drawer with 2 sliding breakers (available also double/4 breakers), screen change speed can be adjusted, TYPE: Semi-automatic, non-stop

AIR PELLETIZER FOR PVC AND COMPOUNDS for throughput 500 to 1500 kg/h connection flange built on Clients design made in steel heated by ceramic heaters, temperature probe and protection carter, stainless steel granulation chamber on horizontal axix, quick opening, knife-holder with fluctuating star to reduce knives consumption., self adjusting knives to nozzle by means of a spring which keeps knives pressed, with less wearing out and increased efficiency n.1x 3 kw motorwith extra strong bearing and long shaft, cutting die in anti-wear steel with number and Ø of holes bespoke to project. 1,5 kw blower, Venturi system, knife template, electric cabinet and touch screen control board with modem for remote assistance

PELLETIZERS WATER RING, Constructed with first quality materials and components they are reliable accessories to your extrusion line, compact and economic., made in sturdy stainless steel, With self adjusting knives to nozzle, with less wearing out and incresed efficiency, re-circulating water pump with water filtering unit for re-use, Heat exchanging unit included. You can connect it with your factory chilling unit., electric cabinet with Siemens touch screen for setting all parameters, Modem for remote assistance, Suitable for a variety of plastics and masterbatches., Size bespoke to your project : 100 to 3.000 kg/h, Materials : LDPE HDPE LLDPE PP PS PC ABS, CAPACITY: 100-3.000 KG.

For electric motors, transformers and alternator stators and allows to separate copper, aluminum and iron. We can offer 3 versions of this machine :, 1) Horizontal extractor to remove the Copper ring rotors with Ø 40 to 240 mm., 4,5 kw installed power, weight 1.000 kg, oil tank 50 lt., Dimensions 1,5 x 1,0 x 2,5 mt. LxWxH, Euro 18.000, 2) Horizontal extractor + Splitting knife to split the motor outer casing (usually AL or Cast Iron) and cutting the stators in 2 halves to extract Copper, 11 kw installed power, weight 1.100 kg, oil tank 50 lt., Dimensions 1,5 x 1,0 x 2,5 mt. LxWxH, Euro 32.500, 3) Horizontal extractor (1) + Splitting knife (2) + Vertical extractor that can extract copper from rotors up to 500 mm Ø and stronger rotors with the help of hydraulic pliers., 11 kw installed power, weight 1.250 kg, oil tank 50 lt., Dimensions 1,5 x 1,0 x 2,5 mt. LxWxH, Euro 38.000, Video avail ...

GUILLOTINE REEL SPLITTER 30T, Working width 1.500 mm Working height 1.250 mm Cutting force 1×30 Ton., No.1 pump 24 l/min, Volume 16 ccm, Speed : up 53 mm/sec, Speed down (80 Bar): 25 mm/sec, Oil tank : 135 lt. Single piston with 2-sides racks to avoid any oscillations and swaying 7,5 Kw drive 400V 50 Hz Safety devices included : Emergency STOP button+ pull-rope STOP+ Knife protection + 2-hands operation + protection grids + hydraulic knife locking system. hydraulic pack can be lodged on top for space saving Complete with control panel User’s manual, drawings, CE compliance for overseas transport, you will need an out-of-gauge 20’fcl Possible addition of conveyor belt, reel disposer, spare knife on separate offer., AVAILABILITY: STOCK - NEW, Force: 30 T

GUILLOTINE REEL SPLITTER 50 T, Working width 2.500 mm, Working height 1.500 mm, Cutting force 2x25 Ton., No.2 pumps 38+38 lt/min, volume 26,4+26,4 ccm, Speed up: 51 mm/sec, Speed down : (80 Bar) 31-15 mm/sec, Oil tank 255 lt., 15 Kw drive 400V 50 Hz, With Knife protection, hydraulic locking system, pull rope emergency system, protection grids, complete with control panel, top lodging, space saving for hydraulic pack, Users manuals, drawings, CE compliance, 12 month limited warranty, Possible addition of conveyor belt, reel disposer, spare knife on separate offer., Force: 50 T

SINGLE SHAFT SHREDDER 150 kw (or 180 kw), sturdy structure in electro-welded steel, cutting chamber dimensions mm. 2000x1000, electro-welded sheet metal hopper for top loading, installed power on the rotor 75 + 75 kw optional 90 + 90 kw, hydraulic unit power 11 kw (15 HP), transmission by belts, 1 rotor, rotor diameter 480 mm., rotor length 2000 mm., 122 reversible tools, 4 usable tool sides, 8 upper fixed blades, 8 lower fixed blades, 73 average rotor revolutions/min., weight 13000 kg, production 3500-5000 kg/h, emergency stop, drawer inversion system, supports for bearings with sealing system against dust and liquids, Adjustable steel counterblade, hydraulically operated pusher drawer with 1000 mm of useful stroke, transmission system by means of pulleys and belts, electrical panel according to EEC standards with inverter, SIEMENS main internal board, Power: 150 kw or 180 kw, width: 2. ...

SINGLE SHAFT SHREDDER 37 kw, sturdy structure in electro-welded steel, cutting chamber dimensions mm. 700x1250, electro-welded sheet metal hopper for top loading, installed power on the rotor 37 kw (50 HP), hydraulic unit power 4 kw (5,4 HP), transmission by belts, 1 rotor, rotor diameter 400 mm., rotor length 700 mm., ram stroke 800 mm., 44 reversible tools, 4 usable tool sides, 3 upper fixed blades, 3 lower fixed blades, 73 average rotor revolutions/min., weight 4460 kg, production 800-1200 kg/h, emergency stop, drawer inversion system, supports for bearings with sealing system against dust and liquids, Adjustable steel counterblade, hydraulically operated pusher drawer with 500 mm of useful stroke, transmission system by means of pulleys and belts, electrical panel according to EEC standards with inverter, SIEMENS main internal board, Power: 37 kw, width: 700 mm. 27.56

SINGLE SHAFT SHREDDER 55 KW, sturdy structure in electro-welded steel, cutting chamber dimensions mm. 1100x1300, electro-welded sheet metal hopper for top loading, installed power on the rotor 55 kw (75 HP) optional 75 kw (100 HP), hydraulic unit power 5,5 kw (7,5 HP), transmission by belts, 1 rotor, rotor diameter 400 mm., rotor length 1100 mm., 66 reversible tools, 4 usable tool sides, 4 upper fixed blades, 4 lower fixed blades, 73 average rotor revolutions/min., weight 5500 kg, production 1200-2000 kg/h, emergency stop, drawer inversion system, supports for bearings with sealing system against dust and liquids, Adjustable steel counterblade, hydraulically operated pusher drawer with 800 mm of useful stroke, transmission system by means of pulleys and belts, electrical panel according to EEC standards with inverter, SIEMENS main internal board, Power: 55 kw

SINGLE SHAFT SHREDDER 75 KW, sturdy structure in electro-welded steel, cutting chamber dimensions mm. 1300x1300, electro-welded sheet metal hopper for top loading, installed power on the rotor 75 kw (100 HP) optional 90 kw (120 HP), hydraulic unit power 5,5 kw (7,5 HP), transmission by belts, 1 rotor, rotor diameter 400 mm., rotor length 1300 mm., 80 reversible tools, 4 usable tool sides, 5 upper fixed blades, 5 lower fixed blades, 73 average rotor revolutions/min., weight 6200 kg, production 2500-3500 kg/h, emergency stop, drawer inversion system, supports for bearings with sealing system against dust and liquids, Adjustable steel counterblade, hydraulically operated pusher drawer with 800 mm of useful stroke, transmission system by means of pulleys and belts, electrical panel according to EEC standards with inverter, SIEMENS main internal board, Power: 75 KW, width: 1.300 mm. 51.18

SINK-FLOAT SEPARATION TANK for PLASTIC SCRAPS, Constructed in thick AISI 304 STAINLESS STEEL with reinforced plates and profiles, Dimensions mt.13,2 x 2,96, Inlet hopper for shredded plastics, Flanged water in/out ports, taps and ball valves, n.6 x 1,5 kw.driven rollers for material movement with Bonfiglioli gearboxes, n.2 chain conveyors on bottom to extract the sunk materials, n.1 diagonal stainless steel chain conveyor, collection drained auger for extraction of floating material, size: 13 x 3 mt., CAPACITY: 2.000-3.500 kg/h

Starting product : car and truck tyres (excluding forklift and loaders tyres) max diam. 1.200 mm, (larger tyres need pre splitting), Final product : 2-4 mm.crumbs, 1-2 mm.crumbs, 2 operators per shift, calculated on a 220 days/year 8 h/day = 1.760 T/year - 16 h/day = 3.520 T/year, Required space : about 25 x 15 mt., Harmonized steel as a residual product., Average throughput rate of granulate : 1 Ton/h (throughput rate depends on feeding rate and on the kind of tires), installed power : about 380 kw used at 65%, Delivery time : about 6 months from confirmation, Main machines:, Debeader - manual (20-25 tyres/h) for truck tyres only, feeding conveyor belt, Dual shaft shredder 1.300 mm wide, transport belt, transport belt for fine material, transport belt to return oversized material to shredder, High speed granulator 1.300 mm wide rotor, extraction belt, vibrating table, Overbelt magnetic  ...

GUILLOTINE REEL SPLITTER 50 T, Working width 2.500 mm, Working height 1.250 mm, Cutting force 2x25 Ton., No.2 pumps 38+38 lt/min, volume 26,4+26,4 ccm, Speed up: 83 mm/sec, Speed down : (80 Bar) 20-41 mm/sec, Oil tank 255 lt., 15 Kw drive 400V 50 Hz, With Knife protection, hydraulic locking system, pull rope emergency system, protection grids, complete with control panel, top lodging, space saving for hydraulic pack, Users manuals, drawings, CE compliance, 12 month limited warranty, Possible addition of conveyor belt, reel disposer, spare knife on separate offer., See item [RES100](https://www.germanplast.eu/listings/4115633-guillotine-reel-s litter) for full description., Force: 50 T

Starting product :, car, 4x4, truck tyres, agri tyres max diam. 1.400 mm and max thickness 300 mm., Final product : 80 - 100 mm.chopped (for inceneration), 4 - 6 mm.crumbs, 2 - 4 mm.crumbs, 1 - 2 mm.crumbs, 0,5 - 1 mm.crumbs, 3 operators per shift, required space : about 30 x 22 mt., calculated on a 220 days/year 8 h/day = 3.520 T/year - 16 h/day = 7.040 T/year, Harmonized steel as a residual product., Average throughput rate of granulate : 2 Ton/h in input (throughput rate depends on feeding rate and on the kind of tires), installed power : about 650 kw used at 65%, Delivery time : about 6 months from confirmation, Main machines:, Debeader - available manual (20-25 tyres/h) or automatic (45-50 tyres /h), for truck tyres only, feeding conveyor belt, Dual shaft shredder 1.500 mm wide, transport belt, discs screen, transport belt, transport belt for fine material, transport belt to return  ...