Category: 107 sheet metal working / Cutting-To-Length Lines
Latest update: 15.11.2023 add to watchlist
approved
dealer
item-No.: 160711524

used

check Seller: MAchine MW
Location: Land-us

add to watchlist

2000mm x 8mm x 30ton FIMI CTL Line Cut-to-length line FIMI 2000mm x8mm x 30t can help you handle all your cutting needs with sheet metal up to 8mm thickness, 20000 mm width and 30t maximum coil weight. This line is equipped with two levelers to provide high top straightening quality and flying shear to make cutting process perfect Manufacturer: FIMI – ITALY Year: 1990 Material: CR-GZR-RP-RKK Yield Strength: 180-400 Mpa Tensile Strength: 220-550 Mpa Coil Width: 800-2000mm Coil Thickness: 1-8mm Coil Weight: 30 Ton Line Speed: 1-25m/min Direction: Left to Right Sheet Tolerance/Size: Length Tolerance: +/- 1 mm Diagonal Tolerance: 0.1% x Sheet width Sheet Width: 800 – 2000 mm Sheet Length: 3000 – 12000 mm Electric AC: 380V /50 Hz / 3 phase AC Control Voltage: 110 V Control Voltage: 24 V Double Mandrel Uncoiler Sliding Base Powered Mandrel Expansion Powered ...

Category: 107 sheet metal working / Cutting-To-Length Lines
Latest update: 19.12.2023 add to watchlist
approved
dealer
item-No.: 161595383
New in: 2004

used

check Seller: MAchine MW
Location: Land-ua

add to watchlist

FIMI cut-to-length line for stainless steel 1500x3mm x25t (A3776) FIMI cut-to-length line for stainless steel 1500x3mm x25t (A3776) is perfect solution for stainless steel metal processing. Line is pretty new and very good conditions. It has all important parts for working. All components made by FIMI. FIMI -is top quality coil metal processing machinery manufacturer Manufacturer: FIMI Year: 2004 (2018 was installed new controller box and plc new) Working length: 1500mm Minimum metal thickness: 0.4-0.5mm Maximum metal thickness: 3mm Maximum coil weight: 25t Supply scope: -coil car -decoiler -entrance feeder -entrance shear -levelling machine -wrapping part -guillotine -conveyor -stacker

Category: 1300 other machines and plants
Latest update: 18.03.2024 add to watchlist
approved
dealer
ankerimg
item-No.: 142701255
New in: 1995

used

check Seller: MET-TECH GMBH
Location: 61381 FRIEDRICHSDORF, AM RINGELSBERG 8 Land-de

add to watchlist

Qty. 1 Second-hand cut-to-length line Mfc.: FIMI, SSW Type: Multiblanks line 1850x2.5 Built: 1995 Stopped: Strip width: 300 – 1850 mm Thickness: 0.3 – 2.5 mm Length: 300-8000 mm Line speed: 85 m/min. Coil weight: 22.5 T Scope of supply: 1. Load coil 25 ton 2. Coils centering 3. 25 ton unwind rod 4. Wire guide photocell 5. Table introduction aprirotolo 6. Group introduction 7. Cutter fly shear 8. 6° FIMI straightener 9. Apply film 10. Circular shear 11. Deceleration/Connection table 12. Wrap waste 13. Ansa passage table 14. Measurement wheel 15. Unique rotary shear 16. First evacuation conveyor 17. Second conveyor for evacuation 18. Scrap unit 19. Autom. wagon for pallet insertion 20. Stacker with palette and air breath 21. Evacuation chain with weight and semi-automatic strapping machine 22. Second evacuation chain 23. Hydraulic units 24. Electrical pan ...

Category: 107 sheet metal working / Longitudinal Cutting Lines
Latest update: 24.01.2024 add to watchlist
approved
dealer
item-No.: 163206529

used

check Seller: MAchine MW
Location: Land-es

add to watchlist

Slitting line Fimi 1500×2.5mm x15t (A3783) Manufacture FIMI ITALY Year 1990 Strip width Min. 200 mm Max. 1500 mm Strip thickness 0.3 – 2.5 mm Coil weight Max. 15 t Coil- Max. 1500 mm Speed Max. 80 m/min Working direction Right  Left The line consists of:  Decoiler Mandrel Cone-Ø 480 – 610 mm Drive / braking Hydraulic motor Lifting table Hydraulic  Coil opener / pinch roll unit Telescopic table Hydraulic No. of pinch rolls 2 Pinch roll-Ø 400 mm Driving motor 25 kw  Slitting head No. of heads 2 Shafts diameter 120 mm Main drive D.C. motor Driving power 92 kW  Scrap baller  Minimum scrap width 5 mm  Maximum number of slits 17 Slits up to 1.0 mm 5 Slits at 2.5 mm  Brakes Pneumatic Press up and dow  Re coiler Capacity 15 t Diameter 508 mm Driving power 120 kw  Term style 4 arms x 15 ton

Category: 107 sheet metal working / Recoilers
Latest update: 15.01.2024 add to watchlist
approved
dealer
item-No.: 152731594
New in: 2003

used

check Seller: HEGO Blechverarbeitungsmaschinen GmbH
Location: 76467 Bietigheim Land-de

add to watchlist

Strip thickness / strip thickness: 3 - 4 mm Coil weight max.: 10,000 kg Coil inner diameter/coil inner-dia.: 508 mm Coil outer diameter / coil outer-dia.: .700 mm Thorn width / mandrel width: 1,650 mm Low-return / pressure arm Separierarm / separating arm Hydr. Spread / hydr. Spreading Working dircetion: right/left; Right/left On board hydraulic pipes 24 VGS or 110 V, 50 Hz. On board hydraulic piping 24 V DC or 110 V, 50 Hz.

Category: 305 peripheral equipment (e.g. heating,cooling,drying)
Latest update: 29.03.2024 add to watchlist
approved
dealer
item-No.: 163395710
New in: 2007

used

check Seller: GERMANPLAST SRL
Location: ponderano Land-it

add to watchlist

FIMIC RAS 400, fully automatic screenchanger, possible setting as : continuous scraping, scraping on an Amp.threshold, mounted on extruder producing 1200 kg/h with 250 my screening, 30 kw drive, machine in good working conditions, totally reconditioned in 2020, constructed in 2007, installed power : 30

Category: 107 sheet metal working
Latest update: 29.03.2024 add to watchlist
approved
dealer
item-No.: 163120507
New in: 2023

new

check Seller: HESSE+CO GesmbH
Location: Land-at
Price: 17.050 € add to watchlist

: neu : 2023 : 9676 : prompt, Zwischenverkauf v : Deutschland : 17050 € : 349.53 € : 1 : 1250 mm : 1.25 mm : 1,25 mm bei 1 Messerpaar, : 2 Stk. : 0.37 kW : 36 m/min : 70 mm : 1900 mm : 1600 mm : 1000 mm : 350 kg 3 PAIRS OF BLADES Length measuring by wheel Digital preselection of one position Brake motor Rubber feeding rolls Manual crosscutting equipment in front and behind blade shaft with 1 cutting slide which alternaingly can be used on front and backside User manual in GERMAN Options: Additional pair of blades € 510,- Additional cutting unit € 1.120,- The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Category: 107 sheet metal working / Cutting-To-Length Lines
Latest update: 18.03.2024 add to watchlist
approved
dealer
ankerimg
item-No.: 147022390
New in: 2006

used

check Seller: MET-TECH GMBH
Location: 61381 FRIEDRICHSDORF Land-de

add to watchlist

Qty. 1 Second-hand cut-to-length line Mfc.: Stratega Built: 2006 Direction right to left Strip width: 400 - 2020 mm Thickness: 0.4 – 2.5 mm De-coiler ID 508, 610 mm Weight: 25 Ton Length of sheets: 300 – 2000 mm Speed: 60 m/min. Leveller Tilting shear Magnetic belts stacker Consist of: Load cradle De-coiler Award spire Introduction table Leveller Feeder Towing pinch roll Tilting shear Evaquation shear wasting material Conveyor Magnetic stacker Eletrical panels & Control Hydraulic station Note: The lien has the guillotine that can cut metal sheet with trapez format cause the guillotine Can rotate or can be used as a normal cut-to-length line.

Category: 107 sheet metal working / Cutting-To-Length Lines
Latest update: 18.03.2024 add to watchlist
approved
dealer
ankerimg
item-No.: 150846397
New in: 1966

used

check Seller: MET-TECH GMBH
Location: 61381 FRIEDRICHSDORF Land-de

add to watchlist

Qty. 1 Second-hand cut-to-length line Mfc.: Ungerer Built: 1966 Material: Stainless steel Strip Width: 300 mm- 1500 mm Thickness: 1.5 mm (stainless steel) Cut length: 750 mm- 6000 mm Length adjustment: mechanical Coil weight: 9.000 kg Coil min/max inner Ø: 500 & 600 mm Shear Type: Rotary Hydraulic system Stacker capacity: 2000 ton PLC: Allen Bradley Scope of supply: Decoiler Crop shear Edge trimmer Leveller PVC film applicator Stacker Camera system

Category: 107 sheet metal working / Cutting-To-Length Lines
Latest update: 15.01.2024 add to watchlist
approved
dealer
item-No.: 152748124
New in: 1975

used

check Seller: HEGO Blechverarbeitungsmaschinen GmbH
Location: 76467 Bietigheim Land-de

add to watchlist

Technical data : Bandwidth / strip width: 1,800 mm Strip thickness / strip thickness: 0.5 - 1.5/2.0 mm Coil weight: 30,000 kg Coil inner/ coil inner-a: 508 mm Coil outer / coil outer-a: 2,000 mm

Category: 107 sheet metal working / Cutting-To-Length Lines
Latest update: 15.11.2023 add to watchlist
approved
dealer
item-No.: 158635300

used

check Seller: MAchine MW
Location: Land-es

add to watchlist

Cut to length line Bronx CTL 1-5mm 400-1500 15 MT Material: CR, HR, P&O GALVA Thick (mm): 1,0 – 5.0 Width (mm): 400 – 1500 Weight max: 20 MT Coil Int. Diam.: 508/610/700 Coil Ext. Diam max (mm): 2000 Length Produced (mm): 500 – 4000

Category: 107 sheet metal working / Cutting-To-Length Lines
Latest update: 15.11.2023 add to watchlist
approved
dealer
item-No.: 158635307

used

check Seller: MAchine MW
Location: Land-us

add to watchlist

60″ x .105″ x 20000Lb Strilich – Voss Cut to length line Make: Strilich – Voss Material Width: 12″ – 60″ Material Thickness: .020″ – .105″ Weight Capacity: 20,000Lb Coil ID: 20″ Coil OD: 72″ Direction: Left to Right Entry 3-Arm Turnstile Powered Rotation ID Protective Bars Entry L-Type Coil Car Powered Lift & Traverse Self Contained Hydraulics Push Botton Controls Mandrel Uncoiler Powered Mandrel Expansion Powered Hold-Down Roll Sliding Base Feed-Up Motor Water Cooled Brake

Category: 107 sheet metal working / Cutting-To-Length Lines
Latest update: 15.11.2023 add to watchlist
approved
dealer
item-No.: 158642032

used

check Seller: MAchine MW
Location: Land-us

add to watchlist

Cut to length line 72″ x .075″ x 40000Lb Rowe / Herr Voss Make: Rowe / Herr Voss Material Width: 12″ – 72” Material Thickness: .020″ – .075” Weight Capacity: 40,000Lb Coil ID: 20″ Coil OD: 72” Speed: 160 feet per minute Sheet Max Length :12′ Direction: R-L Entry Coil Car Floor Standing V-Type Design Powered Lift & Traverse Control Panel Mandrel Uncoiler 4-Leaf Mandrel Powered Hold-Down Roll Motorized Expansion Feed-Up Motor Sliding Base Coil Straightener Driven Pinch Rolls Six (6) Adjustable Work Rolls DC Motor Drive Herr–Voss 6-Hi Precision Leveler Model: RH/84-1.500-19-9-6Hi Work Roll Width: 84″ Work Roll Diameter :1.500″ Number of Work Rolls: 19 Number of Back Up Flights: 9 Powered Work Rolls Adjustment 75HP DC Motor Drive Electrical Controls Rotary Edge Trimmers Mechanical Scrap Chopper Scrap Conveyor Fee ...

Category: 107 sheet metal working / Cutting-To-Length Lines
Latest update: 15.11.2023 add to watchlist
approved
dealer
item-No.: 158757356

used

check Seller: MAchine MW
Location: Land-us

add to watchlist

48″ x .076″ x 20,000Lb Rowe – Voss Cut to length line Cut to length line 48″ x .076″ x 20,000Lb Rowe – Voss Make: Rowe – Voss Material Width: 12″ – 48″ Material Thickness: .017″ – .076″ Coil Weight: 20,000Lb Coil ID: 20″ Coil OD: 72″ Entry V-Type Coil Car Mandrel Uncoiler with Hold-Down Roll 9-Roll Coil Straightener with DC Motor Voss 4-Hi Precision Leveler with 19 Work Rolls 1.156″ Work Roll Diameter 40HP Moto High Speed Shear Drop Type Stacker with Driven Conveyors

Category: 107 sheet metal working / Cutting-To-Length Lines
Latest update: 15.11.2023 add to watchlist
approved
dealer
item-No.: 158757358

used

check Seller: MAchine MW
Location: Land-us

add to watchlist

60″ x .135″ x 20,000Lb Dahlstrom CTL Line Coil Width: 12″ – 60″ Material Thickness: .015″-.135″ Coil ID: 20″-24″ Speed: 180 fpm Direction: Left to Right Entry Floor Standing Coil Car Mandrel Uncoiler with Powered Expansion Motorized Hold-Down Roll Feed-Up Drive Hydraulic Peeler 9-Roll Coil Straightener with 4″ Work Rolls Driven Entry Pinch Rolls 40HP Motor Adjustable Hump Table Mechanical Shear Belt Conveyor with Positive Stop Device Air Gate Sheet Stacker, with Two Section of Gravity Rolls

Category: 107 sheet metal working / Cutting-To-Length Lines
Latest update: 15.11.2023 add to watchlist
approved
dealer
item-No.: 158765970

used

check Seller: MAchine MW
Location: Land-us

add to watchlist

60″ x .625″ x 100,000Lb McKay Slitting Line Make: McKay Material Thickness: .065″ – .625″ Maximum Material Width: 66″ Weight Capacity: 100,000Lb Coil ID: 24″ – 30″ Exit ID: 30″ Coil OD: 90″ Maximum Speed: 450 fpm Direction: L-R Pit Type Entry Coil Car Double Mandrel Uncoiler with Hold-Down Roll Hydraulic Peeler Driven Pinch Rolls Coil Flattener with 200HP Drive Slitting Head with 16″ Arbor Diameter 250HP Drive Knives & Tooling Two (2) Scrap Choppers Recoiler with Over-Arm Separator 250HP DC Drive Exit Pit Type Coil Car Electrics, Hydraulics Controls, Tooling

Category: 107 sheet metal working / Cutting-To-Length Lines
Latest update: 15.11.2023 add to watchlist
approved
dealer
item-No.: 159022448

used

check Seller: MAchine MW
Location: Land-us

add to watchlist

60″ x .080″ x 30,000Lb Iowa Precision / Herr Voss Multi Blanking Line Make: Iowa Precision Material Width: 12″ – 60″ Material Thickness: .010″ – .080″ Coil Weight: 30,000Lb Coil ID: 20″ Coil OD: 72″ Direction: Left to Right Entry Coil Car V-shape Floor Standing Design Powered Lift & Traverse Mandrel Uncoiler 3-Leaf Mandrel Design Powered Expansion Powered Hold – Down Roll Electrical Drive Panel Hydraulic Peeling Table Adjustable Edge Guides Driven Pinch Rolls Adjustable Coil Braking Rolls Herr – Voss 4-Hi Precision Leveler Work Roll Diameter: 1.50″ Work Roll Width: 74″ Number of Work Rolls: 19 Adjustable Work Rolls Up & Down Back Up Flights Variable Speed Motor and Gear Box Electrical Drive / Control Panel Slitter / Shear Make: Iowa Precision Model: Slear 3 Entry and Exit Pinch Rolls Slitting Head with Knives Hydraulic Flying ...

Category: 107 sheet metal working / Cutting-To-Length Lines
Latest update: 15.11.2023 add to watchlist
approved
dealer
item-No.: 159113602

used

check Seller: MAchine MW
Location: Land-it

add to watchlist

Cut to length line Redman 2000mm x 13mm x 20 ton Make: Redman (UK) Material Width: 600mm – 2000mm Material Thickness: 6mm – 13mm Coil Weight: 20 ton Coil ID: 460mm – 760mm Coil OD: 1800mm Max Speed: 20 meters per minute Production Mode: Stop / Start Direction: R-L Entry V-Type Coil Car Double Mandrel Uncoiler Hold-Down Roll Hydraulic Peeling Table Driven Pinch Rolls Pinch Rolls Diameter: 330mm Corrective 4-Hi Leveler Nine (9) Working Rolls Work Rolls Diameter: 140mm Hydraulic Work Rolls Adjustment Up and Down Back Up Flights 120HP DC Motor Drive Mechanical Shear with Motor Belt Conveyor with Measuring Head Drop Type Stacker with End Conveyors Electrics, Hydraulics, Controls

Category: 107 sheet metal working / Cutting-To-Length Lines
Latest update: 15.11.2023 add to watchlist
approved
dealer
item-No.: 159131738

used

check Seller: MAchine MW
Location: Land-it

add to watchlist

Multi Blanking Line Iowa Precision 72″ x 14g x 20,000Lb Make: Iowa – Precision Model: Slear – 2 Condition: Very Good Material Width: 12″ – 72″ Material Thickness: .008″ – .080″ Coil Weight: 20,000Lb Coil ID: 20″ Coil OD: 72″ Speed: 150 feet per minute Entry V-Type Coil Car Mandrel Uncoiler Powered Over-Arm Separator Entry Table Driven Pinch Rolls Adjustable Edge Guides Slitting Head with Tooling Blade Position Indicator 6-Roll Coil Straightener Adjustable Work Rolls Flying Shear Controls with Operator Panel Electrics, Hydraulics, Controls, No Stacker

Category: 107 sheet metal working / Cutting-To-Length Lines
Latest update: 15.11.2023 add to watchlist
approved
dealer
item-No.: 159373183

used

check Seller: MAchine MW
Location: Land-es

add to watchlist

Cut to length line LDM Spotti 1500x6x25t (two levelers, flying shear) LDM CUT TO LENGTH LINE 1500X6 YEAR OF CONSTRUCTION 2000 TYPE 1500X6 THICKNESS 0.5 mm – 6.0 mm WIDTH 390 mm – 1500 mm SPEED 30 m/min UNCOILER CAPACITY 25 ton SHEET’S LENGTH 490 mm – 8400 mm DIMENSIONS 44 m X 9 m (LXW) UNCOILER: 1. DOUBLE CONE WITH EXPATION 2. I.D. = • Φ508 & Φ610 & Φ760 • Φ680 & Φ700 & Φ780 WITH O RINGS 3. O.D.= • MAX = 2000 mm • MIN = 1100 mm COIL CAR: MAX LIFTING CAPACITY = 25 Mton COIL OPENER & PRE-LEVELER: 1. 2.00 mm – 6.0 mm 2. MAX WIDTH = 1500 mm 3. 5+1 LEVELING ROLLERS Φ130 4. 52 KW DC MOTOR 1 ST LEVELER: 7. 0.50 mm – 2.5 mm 8. 390 mm – 1500 mm 9. 280 N/mm2 – 480 N/mm2 10. 19 ROLLS Φ43 mm 11. 7 + 7 BACK UP ROLLS 12.44.3 KW DC MOTOR FLYING SHEAR: 1. 0.50 mm – 6.0 mm 2. 1500 mm CONVEYOR BELT: 1. LENGTH 6000 mm 2. WIDTH 1600 MM STA ...

Category: 107 sheet metal working / Cutting-To-Length Lines
Latest update: 04.10.2023 add to watchlist
approved
dealer
ankerimg
item-No.: 159728908
New in: 1995

used

check Seller: HEGO Blechverarbeitungsmaschinen GmbH
Location: 76467 Bietigheim Land-de

add to watchlist

Bandwidth.......................... 1,500 mm Band thickness..................... 0.7 - 4.0 mm Coil weight................... 20 to. Velocity................ 14 m/min. Working direction right/left

Category: 107 sheet metal working / Cutting-To-Length Lines
Latest update: 22.02.2024 add to watchlist
approved
dealer
item-No.: 160003812

used

check Seller: TechModus LT
Location: 09133 Vilniaus Land-de

add to watchlist

Pivatic perforating and bendingline Line is manufactured 1999 and it has worked very well for us 20 years. Line is bending line with perforation unit and single press unit 35 tn. In line is separate punching unit so you can perforate material and cut it to separate ballet. Also you can use separate press toll in line. This press unit we have not used, because we other presses. FORSTNER coil cradle Weingarten Decoiler Dimeco Coil feeding line decoiler - straightener feeder Automatic Flexible punching and rollforming line for C and sigma profiles with centralized adjustment”, from Dimeco (Spain), installed/commissioned in 2019 Dimeco Coil feeding line PIVATIC coil punching line FIMI Slit Coil Decoiler and reel winder tunçman Extrusion - Single screw extruder LEMO INTERMAT Thermoforming - Automatic Roll-Fed Machine Uhlmann Blister machine Accela-Cota 170 l Tablet c ...

Category: 107 sheet metal working / Cutting-To-Length Lines
Latest update: 15.11.2023 add to watchlist
approved
dealer
item-No.: 160209199

used

check Seller: MAchine MW
Location: Land-us

add to watchlist

Fagor cut-to-length high speed line 72'' x 0.135'' x 60,000Lb is machine for cut to length coil metal cutting into metal sheets of required sizes. This machine can be used by coil metal working companies to make preparatory works before main operation. Machine is equipped with feeding unit and acceptance table to make all the process maximum automatic. It allows to make high speed cutting about 200-250 meters per minute. Cutting speed depends on metal thickness you work with, kind of metal, maximum metal cutting width. This machine helps to make preparatory works maximum fast and automatic, saving your time and labor, reduce expenses costs. Machine is equipped with flying shear so help you to save factory space avoiding loop system installation. 72″ x .135″ x 60,000Lb Fagor CTL Line Make: Fagor Year: 2003 Material Width: 12″ – 72″ Material Thickness: .020″ – .13 ...

Category: 107 sheet metal working / Cutting-To-Length Lines
Latest update: 15.11.2023 add to watchlist
approved
dealer
item-No.: 160449390

used

check Seller: MAchine MW
Location: Land-us

add to watchlist

Paxson loop slitting line 72”x0.187”x 50,000Lb Make: Paxson Material Width: 12″ – 72″ (Uncoiler 60″) Material Width: .010″ – .187″ Coil Weight: 50,000Lb Coil ID: 20″ – 24″ Coil OD: 72″ Speed: 500 /1000 fpm Direction: Right to Left Material Strength: 40,000 yield / 50,000 psi shear Material: CR, HR, Galvanized Entry Transfer Cart Mechanical Traverse Entry Coil Car Floor Standing L-Type Design Hydraulic Lift & Traverse Self – Contained Hydraulics Mandrel Uncoiler Powered Hold-Down Roll Powered Expansion Sliding Base Air Cooled Brake Feed-Up Motor Hydraulic Peeling Table Driven Pinch Rolls Mechanical Entry Crop Shear Two (2) Slitting Heads Arbor Diameter: 7.5″ Adjustable Arbors Sliding Outboard Housing 175HP DC Motor Drive with Gear Box Two (2) Scrap Winders Mechanical Drive Powered Open / Close Exit Mechanical Crop Shear R ...

Category: 107 sheet metal working / Cutting-To-Length Lines
Latest update: 15.11.2023 add to watchlist
approved
dealer
item-No.: 160711547

used

check Seller: MAchine MW
Location: Land-us

add to watchlist

Cut-to-length line Delta-Alcos 72”x0.5”x60,000Lb (A3770) Make: Delta / Alcos Material Width: 36" - 72" Thickness Capacity: .048" - .530" Weight Capacity: 60,000Lbs Coil ID: 16" - 24" Coil OD: 72" Yield Strength: 50,000PSI Direction: Right to Left Coil Storage Conveyor Entry Coil Car Hydraulic Lift and Traverse Cone Uncoiler DC Motorized Brake Sliding Base Wichita Cooled Brake Powered Hold-Down Roll Hydraulic Peeling Table Powered In & Out Set of Driven Pinch Rolls Delta Corrective Plate 4-Hi Leveler Number of Work Rolls: 9 Work Roll Diameter: 8" Work Roll Width: 82" Powered Up & Down Back-Up Flights DC Motor & Drive Delta Corrective 4-Hi Leveler Number of Work Rolls: 19 Work Roll Diameter: 4" Work Roll Width: 82" Motorized Back-Up Flights Powered Work Roll Adjustment DC Motor & Drive Alcos Mechanical Shear Down Cut Shear Driven Entry Pinch Rolls  ...

You didn't find your wanted machine? send wanted inquiry to all dealers (no registration necessary)
Banner ad information  
FIMI 3rd category level
  • FIMI cutting-to-length lines (2)
  • FIMI longitudinal cutting lines (1)
  • FIMI recoilers (1)
 
RESALE used machinery 25 years online