used EXNER Hydraulic Double Column Presses

EXNER EXSBR 200 hydraulic press YOM 8/1987 Serial No. 10042 Pressure 200 t Table 1800 x 800 mm Power requirement 65 kW Safety distance 195 mm Overtravel 52 mm Run-on time 120 ms Weight ca. 23 t

pressure:150 t distance between columns:300 mm stroke:180 mm distance table/ram, max. stroke up, adjustment up:300 mm table surface area:570x180 / 300x410 mm table height over floor:875 mm side window:180 mm ram surface:180 mm speed down:250 mm/s speed up:160 mm/s working speed:6 - 12 mm/s oil volume:250 l power requirement:11,0 kW weight:2,4 t dimensions (WxDxH):1,3 x 1,3 x 2,4 m German Safety: permitted for manual loading:UVV 11.064 - VBG 7n5.2 § 20 foundation pit:nicht erforderlich

pressure:40 t distance between columns:495 mm stroke:150 mm distance table/ram, max. stroke up, adjustment up:300 mm table surface area:490 x 400 mm hole in the table:50 mm table height over floor:950 mm side window:155 mm ram surface:150 mm speed down:480 mm/s speed up:480 mm/s working speed:20 mm/s oil volume:115 l power requirement:7,5 kW weight:2,2 t dimensions (WxDxH):1,35 x 1,1 x 2,2 m depth stop:mechanisch foundation pit:nicht erforderlich

pressure:40 t distance between columns:500 mm stroke:150 mm distance table/ram, max. stroke up, adjustment up:300 mm table surface area:480 x 400 mm hole in the table:50 mm table height over floor:950 mm side window:150 mm ram surface:150 mm speed down:480 mm/s speed up:480 mm/s working speed:20 mm/s oil volume:160 l power requirement:7,5 kW weight:2,6 t dimensions (WxDxH):1,1 x 1,4 x 2,4 m German Safety: permitted for manual loading:UVV 11.064 - VBG 7n5.2 light guard:Sick depth stop:mechanical foundation pit:not necessary

a hydraulic four-column press Exner, type H4 SP 450, Y.O.M. 1983, pressure 450 to., side windows 475 mm. Installation height 600 mm, table area 1100 x 850 mm, impact area 300 mm, stroke 200 mm. Dimensions 3100mm x 2100 mm, depth 1,980 mm. Weight 13 to. ]

pressure: 200 t passage width: NA mm stroke: 180 mm table length: 690 mm table width: 530 mm distance between columns: 420 mm total power requirement: 18 kW weight of the machine ca.: t dimensions of the machine ca.: m Hydr. 4-Pillar Press for Embossing/Calibration The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

pressure: 60 t throat: 330 mm stroke: 500 mm table surface area: 640x640 mm ram surface: Ø 120 mm table height: 850 mm tool hole in ram: Ø 50 mm weight of the machine ca.: 7 t The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

pressure: 20 t throat: 185 mm stroke: 100 mm table surface area: 380 x 350 mm dayligth: 250 mm table height over floor: 840 mm total power requirement: 4 kW weight of the machine ca.: 1,3 t The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

pressure: 125 t distance between columns: 1500 / 460 mm stroke: 400 mm total power requirement: 15 kW weight of the machine ca.: 10 t dayligth: 800 mm table surface area: 1900x870 mm ram surface: 1900x870 mm working feed: 0-10 mm/sec return speed: 0-20 mm/sec dimensions: BxTxH 2400x1500x3500 mm The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

pressure: 200 t distance between columns: - mm stroke: - mm table surface area: 2000 x 800 mm total power requirement: kW weight of the machine ca.: 31 t dimensions of the machine ca.: m Drive power 55 / 4 kW Tracking travel 28 mm Safety distance 155 mm Tracking travel time 97 ms Oil filling 1200 liters The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

press ram:: ram head width: 2.100 mm depth: 840 mm stroke: 350 mm Control: EXNER Guide way length: 750 mm nominal pressure: 2x 400 kN return capacity: 2x 150 kN ram stroke speed - under load: 100%: ca. 0 - 10 mm/s ram stroke speed: ca. 0 - 20 mm/s T-slot - width: 18 mm T-slot - distance: 150 mm Installation Space:: dayligth: 550 mm table surface area: 1.600 x 840 mm T-slot - width: 18 mm T-slot - distance: 90 mm dist. between pillars (left to right): 1.700 mm dist. between pillars (front to rear): 600 mm table height over floor: 1.300 mm total power requirement: 11 kW weight of the machine ca.: 12 t dimensions of the machine ca.: 2,5 x 2,0 x 3,7 m Hydraulic tool testing press EXNER - PG 80 - very good condition - approx. 300 operating hours - Electronic roller feed device EV 22 AK incl. Bandwidth: max. 220 mm Band cross section: max. 200 mm² Feed length: 0.1 x 19,999 mm Speed: ...

Pressing force 160kN,pull cushion force 63kN,stoesselstroke 300 mm, pull-cushion stroke 150 mm, recessed height 500 mm, table 630x400,Stoessel 300x250,pull cushion flap 350x270,

Double column press with 200 T output, Idle speed 45 mm/sec Opening speed 60 mm/sec Starting press speed 9 mm/sec Table size 2000x600mm Plunger size 2000x600mm OIL temperature monitoring Manual lubrication Free positioning of the plunger ( adjustable via adjustable sensors ) PILZ photoelectric sensors 14.1 mm on front and back Circulatory oil cooling Pressure retaining valve 0 to 600 sec. Mechanical plunger protection at the upper breakpoint T-grooves according to DIN, and according to customer requirements Pressure adjustment from 40 T to 200 T (adjustable via rotary knob) Travel limitation optionally via pressure or position Set-up operation, single stroke ( adjustable via key switch ) Two-hand operation Construction, commissioning, instruction against separate calculation Design Press design double column press Therma ...

Here are the technical data of the offered machine: Technical data + information: • No-load speed up to 40 mm/sec • Opening speed up to 40 mm/sec • Starting press speed 5–15 mm/sec • Table size/heating plate size 600 × 600 mm • Plunger size/heating plate size 600 × 600 mm • 2 heating plates, electrically heated, up to 250 degrees – as OPTION • Total size approx. 2000 × 1000 × 2800 mm height • OIL temperature monitoring • Automatic lubrication • Free positioning of the plunger • SICK/LEUTZE light barriers 14.1 mm on the front • Circulating oil cooling • Pressure holding valve 0 to 1800 sec. • Rear monitored door • Pressure adjustment from 30 T to 120 T • Travel limitation either by pressure or position • Programming set-up mode, single stroke (adjustable via rotary switch) • Control panel permanently installed in the wall  ...

Inv. Num. : 6701 Type: 4000 kN Producer: Hydraulico Created: 1977 Parameters: Control system: SIEMENS SIMATIC OP Compressive force: 4000 kN Stroke: 800 mm Table height: 680 mm

Inv. Num. : 6700 Type: 3000 kN Producer: Loire Created: 1992 GO 2008 Parameters: Control system: SIEMENS SIMATIC OP17 Compressive force: 3000 kN Table length: 2495 mm Table width: 1505 mm Maximum distance between the table and the ram (when the ram is low): 1200 mm Stroke: 800 mm Working speed: 64 mm/s

Key data: 400 t, 800 mm

Oil-hydraulic double-column press 400 T with sliding table Press type: Double column press Thermally neutral 80 – 120 °C Number of operating pages 1 page Forces Pressing force max. 4000 kN Free tear-off force max. 400 kN Print build-up time Closed tool steel on steel Max. 4 sec. Dimensions: 3,800 mm long and 4,475 mm wide Max. opening width 800mm Stroke 800mm Table height above floor 1100mm Height above ground (height) approx. 4300 mm Hall height min. 5500 mm Parallel deviation at 20°C +/- 0.1 mm Deflection Determined at max. clamping force with 70% occupancy < = 0.2 mm/m Weight Total weight of the press without consumables and table top approx. 28 tons Press table Table size 1500x1500 mm Velocities Quick closing at 100 mm sec. Pressing speed 8 – 3 mm sec. Acoustic pressure Sound pressure level, measured at a height of 1.5m on the control pane ...

Inv. Num. : 7047 Type: HSP 600 AZ-RN a Producer: Brunnhuber Created: 1969 Parameters: Compressive force: 610 t

2 column hydraulic press #5232 Press force: 200 t upper stroke: 500 mm lower stroke: 200 mm overall dimension: 1800x2200x3700 mm Power: 10 PS Weight: 8.4 t

Qty. 1 Second-hand extrusion press line Mfc.: SMS Schloeman, Junker, Allen Bradley Type: Direct press Built: 1987 Force: 2800 MT Billet dia.: 228 mm – 9” Length: 250-1000 mm Consist of: Logs Loading Table Logs Furnace Hot Shear Induction Heater Extrusion Press Pullers (2) Quenching Unit Hot Saw Run-out Table Stretcher Finishing Saw Aging Oven

Qty. 1 Second-hand extrusion press including log furnace Mfc.: SMS Built: 1986 Force: 960 MT (9.3 MN) Press jaw: Wide: 155 mm Height: 140 mm Max. inlet: 130 mm (144 mm block, 5 mm protection per side) Recipient: 149,9 mm Extras: Heatable tool cassette from Marx (installed 2016) Conversion of recipient to resistance heating (beginning of 2016) Punch press disc: 149,2 mm Broaching disc: 150 mm Billet Ø: 144 mm Length: 265 – 540 mm Log length: 3000-4800 mm Log Furnace Mfc.: Extrutec GmbH Built: Temperature: 480-520 °C Zone 1: 460-490 °C Zone 2: 440-470 °C Zone 3: 400-450 °C Table weight: Max. 1350 g/m Min. 80 g/m Electrical control cabinet Puller Exhausting system Cooling device Spare parts for furnace combustion air Spare parts head burner Spare parts oven stove bo ...

PRESS FOR PRODUCTION ALUMINIUM TRAYS FOR ALIMENTARY USE COMPLETE WITH DOUBLE IMPRESSION MOULD-1100 CC. COMPOSED OF: A LUBRICATION UNIT 4-COLUMN MOLDING UNIT TOW-SCRAP CONTROL PANEL. 55 STROKES/MINUTE DEPENDING ON THE MOULDS. PASS COLUMNS FOR MOULDS UP TO 800 MM

Ortlinghaus coupling outer diameter 680 mm from stock as good as new

Capazitat 300 Tone Table size 1,500 x 1,500 mm Stosselv creation 500 - 1,000 mm Piston x 400 mm Delete. Table - Stossel Minimum: 500 mm Maximum: 1,500 mm Machine height 4,000 mm Bottom of the floor 1,000 mm Top of the floor 3,000 mm Machine Weight 18.600 kg

Passage width 2500 mm Stroke 900 mm Total power requirement 62 kW Machine weight ca. 27,5 t Dimensions L x W x H approx. 3950 x 2200 x 4850 mm Retraction force 40 t Master cylinder 2 pieces Column diameter 220 mm Installation height 1300 mm Table size 2500 x 1600 mm Ram size 3100 x 16000 mm Table height above floor approx. 900 mm Flow speed 200 mm/sec Return speed 200 mm/sec Working speed 5 - 15 mm/sec Oil tank 1500 l Oil quantity 1200 l Pressure control adjustable from up to 50 - 400 t Thermoforming cushion 1400 x 800 mm Deep-drawing unit capacity 30 - 60 t Deep-drawing cushion stroke 250 mm Deep-drawing cushion speed 5 - 80 mm/sec robust machine body with solid welded construction low-maintenance and reliable Piston rod with induction hardening and chrome cladding T-slots according to customer requirements, if not specified 22mm according to DIN CE Certific ...