We use cookies to optimize our website for you and to be able to continuously improve it. By continuing to browse the site you are agreeing to our use of cookies.
Disagree
used
Hydraulic guillotine for cutting sheet metal by ESPE Strojarne Piesok, type CNTA, 3150 mm x 6.3 mm (ST40). The machine has a variable knife gap and a hydraulically variable knife angle of 1 -2.5 degrees, set from the desktop. 11 kW motor. Machine weight 7 tons. Bumper departure 950 mm. Electrically adjustable cutting length in the range of 10-3150 mm. 2 supports to hold sheets of metal at the front of the machine, plus a ruler for cutting at a 90-degree angle. Light line enabling line cutting. Original O&M documentation and occupational health and safety manual in Polish. The machine is designed for continuous operation - 3 shifts.
used
Year 1996, CE norm, complete instructions, control Delem, machine in TOP condition with warranty, more details on request
used
Espec Temperature Shock Chamber Here we offer you an Espec temperature shock chamber. Thermal shock environmental chamber (cold load: -65° to 0°C). Conventional thermal shock chambers with three zones can be quite large, since three separate chambers are used. The TSA series has only one chamber, which significantly reduces its size. Instead, it circulates cold, hot or ambient air as needed. The air-conditioned air can be pre-cooled or preheated beyond the setpoint, allowing for faster recovery of the desired state after transmission. Espec Temperature Shock Chamber Water Cooled TSA-201S SN: 153000154 Hot chamber: +60 to 200°C Cold chamber: -70 to 0°C Working temperature: 0-40°C System: Two zones or three zones test by flap switching Achievement: Test area: High temperature. Exposure range: +60 to +200°C Low temperature. Exposure range: –70 to 0°C Temperature fluctu ...
used
This ESPE CTO 250/4000N Bending machine was manufactured in the year 1995 in Czech Republic. The pression force of this machine is 250 T.
used
ESPERA ES 7000 ID.NO. 2106 Espera ES 7000 labeler over + below and extra labeler. Year against 2004. Dimensions 235 x 80 cm H 185 cm.
used
Counting scales, scales, parcel scales, weighing platform without terminal, operating unit, display, evaluation device -Weighing platform without: evaluation device for scales -Weighing range: min.0.02 kg -Weighing range: max. 12 kg -Number: 1x available -Dimensions: 330/235/H90 mm -Own weight: 4.7 kg
used
ESPERA fully automatic weight and price labellers ESPERA LABELLER labeller
used
Description: Device number 993357 Voltage 220 V Frequency 50 Hz Current consumption 0.25 A Approx. Onsite Dimension. (l x w x h): 350 x 350 x 400 mm, weight approx.: 40 kg
used
Description: Device number 99 3167 , 0.25 A,  ,200 V, 50 Hz Approx. Onsite Dimension. (l x w x h): 500 x 400 x 400 mm, weight approx.: 15 kg
used
Key data: 315 t
Inv. Num. : 4650 Type: LODD 315 Producer: ESPE Created: 1996 Parameters: Compressive force: 315 t Maximum bending length: 4000 mm Machine height: 4150 mm Machine length: 4000 mm Machine width: 2200 mm Machine weight: 33 t Equipment: Tools
used
Top used ESPERA labeling machine ES 5000
used
Espera checkweigher with labeller and control panel, type: ESG 154, serial number: 1760000280, 230 V, 50-60 Hz, 10 A, plastic belts, belt width: 140 mm, total dimensions: 1930 mm x 700 mm x 1840 mm.
used
Guillotine shears, FASTI type 506-10-2,5 Masch. Nr. 96-506-018 Year of manufacture 1996 Cutting length 1030 mm Cutting thickness 2.5 mm Working height 850 mm Drive power 4 kW Mains connection 400 volts, 50 Hz. - mechanical sheet metal hold-down - electric foot switch - simple backgauge 550 mm with handwheel adjustment - 2 support arms 550 mm - angle stop right 750 mm - protective housing SICK behind the machine - control cabinet fixed to the machine space requirement L x W x H 2150 x 1650 x 1400 mm weight 650 kg good condition; used
used
guillotine shears, sheet metal shears DIGEP type OL 3 Fabr. No. 1312 Year of construction 1977 Cutting length 1250 mm (nominal cutting length)Cutting length max. 1300 mm Cutting thickness at 450 N/mm² 3 mm single backgauge 500 mm Column projection 200 mm Cutting angle 2 Stroke rate at full cutting length max. 50 strokes/min. Working height 860 mm Motor power 2.2 kW Mains connection 380 volts, 50 Hz - LED cutting area lighting - simple backgauge with manual adjustment - Mechanical foot switch - Front angle stop left - 1 piece front sheet metal supports 300 mm Space requirement L x W x H 1660 x 1350 x 1200 mm Weight 1600 kg good condition; used
used
Working width: 4100 mm sheet thickness: 16 mm projection: 300 mm rear gauge: 1500 mm power: 400 V, 45 kW space: 4800 x 3500 x 2600 mm weight: 28000 kg
used
Working width: 5050 mm thickness: 10 mm power: 30 kW space: 2450 x 5600 x 2500 mm weight: 28000 kg
used
Working width: 4100 mm sheet thickness: 6 mm radius: 100 mm rear gauge: 0-1000 mm power: 18.5 kW space: 4600 x 2200 x 1950 mm weight: 11000 kg
used
Working width: 3050 mm sheet thickness: 6 mm throat depth: 200 mm rear gauge: 1000 mm power: 15 kW space: 4100 x 2300 x 2100 mm weight: 8500 kg well-preserved CNC hydraulic shear, with pivoting Panel, serial control. CYBELEC, CNC 1000, Hours of operation according to the operating hour counter: 2700 h
used
Working width: 3050 mm sheet thickness: 6 mm throat depth: 200 mm rear gauge: 1000 mm power: 15 kW space: 4100 x 2300 x 2100 mm weight: 8500 kg well-preserved CNC hydraulic shear, with pivoting Panel, serial control. CYBELEC, CNC 1000, Hours of operation according to the operating hour counter: 2700 h
Sheet thickness: 10,00 mm Sheet width: 2000 mm Depth rear gauge: 0 mm Maximum sheet thickness: 10mm Max. cutting length: 2.000mm Strokes on full length: 100mm Strokes in short 1000 length:1000 Number of down holders: 11 Approach speed: 50mm/sec. Power: 15kW Length: 2.700 mm Width: 2.050 mm Height: 2.050 mm Weight: 5.900 kg
Technical data: -maximum cutting width 3050 mm -maximum cutting capacity at 45 KP / mm² 4 mm -hydr... Cutting angle adjustment - number of holders of 18 PCs -Speed up to 24 / min -front angle stop 1100 mm -3 PCs front support arms 750 mm -mot. Backgauge positioning control 5-1000 mm - sheet reversible - cutting line illumination -E - foot switch -Rear area protection with light barrier -Drive 400 V / 9.5 kW -Space requirement approx. B 3900 x H 1850 X 2100 mm -Weight approx. 5.7 t
used
Sheet thickness: 25,00 mm Sheet width: 3100 mm Depth rear gauge: 0 mm Maximum sheet thickness: 25mm Max. cutting length: 3.070mm Strokes on full length: 7mm Strokes in short 1000 length: 12 Cutting angle: 0,5 - 2,5 ° Length backgauge: 1.000mm Number of down holders: 15 Control: Siemens Safety guides: Sick Operated mechanical or hydraulic:hydraulic Power: 45kW Length:&nb ...
used
Maximum cutting length: 4000 mm Maximum sheet thickness: 4 mm steel Driven back gauge to 1000 mm Page fence and table extensions Cutting length limit Cutting edge lighting Protection fence, roll with safety switches Weight: 8500 kg
used
Manufacturer: Weinbrenner Type: TSV 6 / 3050 Year of constr.: End of 2015 demonstration machine Cutting length: 3050 mm Cutting capacity: 6 mm (steel) Hours of operation: 54 Control: Cybelec DNC 60 Dimensions L/W/H: 4100/2050/2100 mm Table height: 1000 mm Weight: 8500 kg Min. cutting angle: 1° Cutting angle max.: 2.5 ° Stroke rate minimum: 20 min. Max speed: 25 min. Cutting gap adjustment: motorized Cutting angle adjustment: hydraulic Number of holders: 14 Rear velocity range: 1000 mm Security: setting the photocell safety on the front and back Oil filling: 225 l Electrical power: 15 KW Power consumption: 3 x 400 V / 50 Hz Back-up fuse: 50 A Additional equipment: Extension of the side stop on 2050 mm Side stop side swing-away A total of 8 support arms freely movable along the entire length of the table The machine is a demonstration ...
used
Maximum cutting length: 3080 mm Maximum sheet thickness during cutting: 6 mm Maximum cutting angle: 2 st Total power requirement: 11 kW Rear stop: 1000 mm Machine height: 1950 mm Machine length: 4100 mm Machine width: 2050/3650 mm Machine weight: 7980 t