used CODATTO Bending And Straightening Machines

Description: Semi-automatic numerically controlled panel bending machine, software with cycles up to 8 sockets. Sheet metal gripping system with suction cups, equipped with rear SA blades for folding tabs.  , Main features:  , Folding dimensions Max. bendable length: 3123 mm Min. folding length: 80 mm Max. folding width: 3123 mm Min. folding width: 142 mm Max. fold size (minimum, depending on thickness): 140 mm  , Customised trolley with tool changer equipment, also supplied with spare parts and moulds for additional PSA arrangement. Further information can be found in the attached documentation, ,the measurements given are to be understood with the machine assembled. Around 26000 working hours visible on photo odometer. Approx. Onsite Dimension. (l x w x h): 6,400 x 2,700 x 2,600 mm, weight approx.: Unknown kg

pressure:200 t distance between columns:2900 mm stroke:800 mm dimensions of the machine ca.:3300 x 2700 x 3100 mm Table dimensions:2500 x 2000 mm :4000 mm :33 mm/sec :33 mm/sec distance table - lower edge of ram:1100 mm table height over floor:750 mm :2300 mm return capacity:25 t total power requirement:15 kW Oil Cooling:1 kW stroke speed:18 mm/sec down speed:2 - 10 mm/sec :200 l table plate:100 mm distance between columns:2400 mm open height:1000 mm weight:9 t Table Height:750 mm :34 Lt./min. Impact leper extension removable (200 mm long):550 ? Table top flattened, with or without T-slots:7900 ?

pressure:200 t distance between columns:1550 mm stroke:400 mm dimensions:ca. 4400 x 3250 x 4100 mm Table dimensions:1500 x 1500 mm distance table - lower edge of ram:1590 mm return capacity:20 t total power requirement:20 kW Oil Cooling:1,5 kW stroke speed:25 mm/sec down speed:10 mm/sec :250 l table plate:120 mm Table cut-out:550, 450, 350 und 200 mm table speeds:30 mm/sec

pressure:400 t distance between columns:2500 mm stroke:600 mm Table dimensions:2500 x 2000 mm distance table - lower edge of ram:600 mm total power requirement:18 kW speed of forward flow:9 mm/sec Return Speed:19 mm/sec :67 Lt./min. Total weight, approx.:26 t

pressure capacity max.:50 t

pressure capacity max.:25 t

pressure capacity max.:25 t

Bending semi-automatic, tube bending machine, mandrel bending machine MOBITEC type BAH 1-2 KOTTMANN und BERGER GmbH Fabr. No. 056 Year of manufacture 09/2004 - for simultaneous bending of two steel pipe sections up to 12 mm bending angle max. 90 Tube diameter max 12mm Mandrel length approx. 65 mm Nominal power 3.5 kW Compressed air max. 6 bar / approx. 1 litre per bending cycle Mains connection 400 volts, 50 Hz - Pneumatic clamping - Pneumatic mandrel retraction - Control for angle input via STOBER Controlbox Series 4000/5000 - Control SIEMENS S7-200 with display TD200 - Machine without bending tools and without tool bearing bolt 25 x 183 mm - only 1 bending mandrel available (see pictures). Space requirements L x W x H 1000 x 1000 x 1500 mm Weight 390 kg good condition; used

specifications: - Pressure capacity 100 KN / 10 t - Compressive force adjustable 0 - 100 kN - Stroke length 0 - 150 mm - Clear width approx. 200 mm - Lifting speed 0 - 0.6 m/min - Tool height up to approx. 100 mm - Bending performance - with prism MW 100 flat to approx. 100 x 12 mm - Tube bending up to approx. 1 inch - Directional power Wy at straightening block distance of 1m 100 cm³ - Drive 400 V / 1.1 kW - Space requirement approx. W 1100 x H 1000 x D 650 mm - Weight approx. 400 kg

Key data: 100 t

Bussmann Press HPK 100 Machine number: M 36 65 Offer here a Bussmann frame press on type 100 /5 The press ran until the last minute and only formed sheet metal It has many safety-related devices installed Has been scrapped due to new acquisition from ongoing operation Pressing force: 100t Retraction force: max. 14t Injection piston pressing force: max. 40t Lower piston stroke: 200 mm Stroke upper piston: max. 400 mm Table width / installation width: 650 mm Table depth / installation depth: 650 mm

Key data: 15 t, 66 mm

Burger Press D07 Length 1.20 m Width 0.60 m Height 1.70 m 2 Hand control Switch to foot control 1 press die

pressure:10 t table::350 x 350 mm stroke:10 mm Description: Rotary embossing machine, for labeling or identification of parts like flanges or tubes as for flange descriptions for example ( pressure, material, nominal diameter.. ) The machine is new and unused Made in Germany incl. charsets and symbol set under power Original price in 2007 : ? 33.500,--

combined bending machine-straightening press, profile bending machine, bending machine, flat iron bender, horizontal bending/straightening press, horizontal bending machine -Flat iron bender: hydraulic profile bending machine -Pressure capacity: 140 Ton. -Stroke cylinder: 455 mm -Counter bearing max width: 1250 mm -Support rollers: height adjustable 250 mm -Dimension: 2060/3735/H1620 mm -Weight: 8300kg

unknow A9020411 (12-14)-

Operator Panel

unknow GE.570205.0002.00, part of the set-

Main Rack

BARCO HULPFUNCTIE 16 DIG OUTP

BARCO FLOPamp;KBRD INTF MNC95

Hand - Swivel bending machine KRAMER type AMS 650 x 1.5 Hand swivel bending machine, bending bench Year of construction approx. 1985 Working length 650 mm Sheet thickness at 40 kg/mm2 1.5 mm Upper cheek opening approx. 60 mm Bending cheek adjustment approx. 0-25 mm Bending angle 0-180- Upper cheek adjustment via hand crank - Pre-screw rail for the bending clamp - one-piece sharpening rail 135 Space requirement L x W x H 1200 x 600 x 1100 mm Weight 160 kg good condition; used

Swivel bending machine, cant bench, gutters, roof gutters, beading machine, beading machine, three-roller round, three-roller sheet metal bending machine, bending machine, sheet metal round bending machine, 3-roller round bending machine, profile bending machine, three-roller sheet metal rolling machine -Swivel bending machine: with 3-roller bending machine on a solid base -Max. Working width: 1020 mm -Max. Sheet thickness: 1.5 mm -Roller diameter: 2x 50 mm / 1x 53 mm -Dimensions: 1450/800/H1155 mm -Weight: 346 kg

Bending tool, die, upper knife, upper tool, straight tool, upper beam -Bending tool: for folding machine -Tool angle: 45° -Dimensions: see the drawing in the photos -Dimension: 47 x 11mm -Length: 945mm -Weight: 3.5 kg

Bending tool, matrix, upper knife, upper tool, upper beam -Bending tool: from Lotze HDZ swivel bending machine -Length 2678 mm -Hole spacing: 100mm M10 -Dimensions: see the drawing in the photos -Dimension: 2678/6/H45 mm -Total weight: 5,6 kg

Bending tool, matrix, upper knife, upper tool, upper beam -Bending tool: from Lotze HDZ swivel bending machine -Length 2678 mm -Hole spacing: 100 mm M10 -Dimensions: see the drawing in the photos -Dimension: 2678/15/H57 mm -Total weight: 15.7 kg

Bending tool, die, lower knife, lower tool, lower beam -Bending tool: from Lotze HDZK swivel bending machine -Widening: for lower cheek -Dimensions: 2487 x 100 x 15 mm / 190 x 100 x 15 mm -Hole spacing: 100 x 18 mm -Transport dimension: 2487/100/H30 mm -Total weight: 29.4 kg