We use cookies to optimize our website for you and to be able to continuously improve it. By continuing to browse the site you are agreeing to our use of cookies.
Disagree
used
Saw mill vertical Boegli Weight 4000 kg L x W x H: 200 x 160 x 330 cm Roll diameter 1250 mm Stem Ã? 1.2 m, with mechanical clamping cars 9 m Chuck Wagon L x W x H: 900 x 200 x 170 cm Weight approx. 6000 kg Built 1952 The machine is in good condition, ready to use. Subject to changes, errors, prior sale! Service/spare parts by MATEC CH-4900 Langenthal/DE-79618 Rheinfelden MATEC system + technik GmbH Mechanical engineering Eisenbahnstrasse 25 CH-4900 Langenthal/Switzerland Tel. 0041 62 966 18 32 Fax 0041 62 966 21 12
used
Full frame saw Boegli MARA-2 with Electr. Switchgear with associated Chuck Wagon (REF. No. 262-1491) Masch. No. 373 Through root Ã? 600 mm With hydr. Sheet tensioning device L x W x H: gate 260 x 200 x 450 cmm Weight approx. 1200 to Built in 1978 The machine is in good condition, ready to use. Subject to changes, errors, prior sale! Service/spare parts by MATEC CH-4900 Langenthal/DE-79618 Rheinfelden MATEC system + technik GmbH Mechanical engineering Eisenbahnstrasse 25 CH-4900 Langenthal/Switzerland Tel. 0041 62 966 18 32 Fax 0041 62 966 21 12
used
4 sides trimming line
used
Longitudinal saw without lamella support Cutting length 6200 mm Cutting width 600 mm Cutting height 170 mm Saw motor 11 kw Built in 1989
used
Longitudinal saw with a cutting length of 5200 mm , cutting height 170 mm , cutting width 450 mm , 11 kw motor with control
used
Brettbesäumer Autojet used Cutting heights 18 - 100 mm, 3 variable axes – 2 variable stems – Re./Li. Additional bushing. Build 3/94 - New laser measurement with PC/software/PC cabinet from Installation 5/2007 A cost-effective solution for a fast trimming machine with modern laser measurement. - Continuous capping with length stops for the cap lengths - Zero cross-cut saw - Addition of swivel saw for tip capping on the opposite side. The waste is disposed of. -Transverse measuring conveyor The boards are conveyed by a measurement curtain in transverse passage. -Laser measurement State-of-the-art surveying with 15 lasers from above. Of course, programs can be stored in all variety, depending on length and width, separation, sharp-edged or forest edge can be mapped in many ways in the program. - Alignment table A computer calculates the ideal orientation of the boa ...
used
Cutting saw for cutting waste material. Suitable for processing waste after an angle circular saw. The configuration of the machine and its parameters is by mutual agreement. Technical parameters: Power of the main motors: 2 x 11 kW Power of the feed motor: 0.75 kW Minimum height of the starting material: 15 mm Maximum material length: optional Maximum height of the starting material: optional
used
PAUL recutting saw type s-900-L with a passage width 906 mm, Cutting width 180 mm. The feed is infinitely adjustable 0- 90 m-min. The saw motor has 110 kW. Saw blade diameter 550 mm at 2500 rpm. With automatic feeding, Spreiselabscheider double-lamellig with pull-out tapes
used
I sell a center saw with continuous HOMAG FPL620/06/15/P S/LQ. Year of construction 2007. Working width 204 - 1304mm Element height 12 - 60mm Cutting width 100mm Blank length 300mm Feed speed 10 - 40 m/min. Configuration: 1 + 1 pcs. cutting units top + bottom 1 pcs. cutting unit flexible top/bottom 1 pcs. cutting unit flexible top/bottom 1 pcs. grooving unit with stop and softforming function Material pressure tape with conveying from above. Continuous machine. Condition Very good. Available same.
used
Edging saw – single-blade saw Make Torwegge Type H321 Cutting width 164 mm Chain width 160 mm Main motor approx. 11 kW Cutting height 90 mm Weight approx. 1400 kg
used
Trimming saw Wurster & Dietz Type: FR 7 Passage width 800 mm Cutting height 160 mm with saw blade diameter 500 mm Cutting height 140 mm with saw blade diameter 450 mm Cutting height 120 mm with saw blade diameter 300 mm Motor 22 kW Adjustable slatted bushing Hydraulic feed 0 – 70 m/min. Hydraulic roller lifting Input roller conveyor 6 meters long with 6 rollers, with rods for adjustment of cutting height and speed and batten bushing Output roller conveyor 6.5 m long with push-off in the form of spiral rolls for side goods new spare drive belt complete with operating instructions and wiring diagram Condition: Technically perfect, cleaned and repainted Total weight approx. 5 to. (Trimming saw 3 tons. and roller conveyors and rest 2 tons.) Installation length approx. 15.5 m Loading dimensions: approx. 6.5 loading meters
used
SCM sliding table saw model SI400e: – 3200mm aluminium trolley – motorized lifting of the blade unit, with digital indicator – motorized tilting of the blade unit, with digital indicator – Rip fence with manual adjustment – main blade D=400mm – 3 blade rotation speeds, 3000-4000-5000rpm – independent engraver with external adjustment – engraver rotation speed 8500rpm Machine according to CE standards
used
SPECIFICATIONS: Max. cutting length: 3000 mm Max. cutting height: 50-60 mm Manual Saw Blade Feed Adjustable cutting width Electric/pneumatic operation
used
CASOLIN sliding table saw model ASTRA 3000: – 3000mm steel trolley – width on parallel guide 1100mm – manual lifting and tilting of the blade unit – main blade D=400mm, 5.5 hp motor – 3 blade rotation speeds, 3000-4500-6000rpm – independent engraver, 0.75 hp engine – engraver rotation speed 8000rpm Machine not according to CE standards, for export AVAILABILITY FROM MAY 2024
used
SCM sliding table saw model SI15WF: – 2500mm steel carriage (2700mm stroke) – tilting blade D=400mm max, 5.5 hp motor, with 3 speeds 3200-4500-6000rpm – without engraver Machine not according to CE standards, for export
used
CASOLIN tenosquaring machine model TSX3: – 3000mm steel trolley – protection suspended on the blade – tilting blade D=400mm max, 5.5 hp motor, with 3 speeds 3000-4500-6000rpm – engraver D=110mm, motor hp 0,75, 8000rpm – cutting width on rip fence 950mm – spindle moulder with shaft D=35 x L=170mm, engine hp 5.5 , with 4 speeds 3000-4500-6000-8000 rpm – weight approx. 1500 kg Machine not according to CE standards, for export
used
Used ALTERDORF sliding table saw mod. F45 Serial number 07-08-10-142 Electronically controlled two-axis adjustment for tilt and cutting height with automatic gradage-dependent blade height correction Digital Rip Fence Viewer Maximum carriage stroke mm 5000 Maximum cut at the square fence mm 4420 Maximum tilt from 0 to 45 degrees Machine without engraver Maximum cut at rip fence mm 1350 Maximum blade diameter mm 550f Engine power 15 hp N. 3 blade rotation speeds: 3000/4000/5000 rpm Maximum cutting height 200 mm at 90 degrees Maximum cutting height 139 mm at 45 degrees Year 2007 EC
used
SPECIFICATIONS: Max. saw blade diameter: 400 mm Saw blade inclination: 0° - 45° Length of the trimming carriage: 3800 mm Scoring capacity: KW 0.75 Scoring diameter: 120 mm Max. cutting height: 130 mm Installed power: 5.5 KW
used
4-side squaring and edge banding line Machine 1: Fixed side right, moving side left Rolling chain, feed 10 - 40 m/min Controlls NC 21 Panel thickness 8 - 60 mm Max. panel width 1500 mm Edges: coil 0,3 - 3 mm, strips 0,4 - 20 mm Entry fence for veneered panels Equipment: 1+1 Compact-twin hogger, 2 motors 6,6 kW 1+1 Compact hot melt unit A20 with panel edge pre-heating, glue roller Q34, twin coil magazine, lateral pressure rollers C including anti-stick application 1+1 Free space for solid wood edges up to 2,54 m length 1+1 Rough trimming, 2 x 1,5 kW 1+1 Fine- or radius trimming, 2 x 0,4 kW (edges up to 6 mm) 1+1 Universal shaper 8,1 kW 1+1 Universal shaper 8,1 kW 1+1 Edge sander KS 10 1+1 Disc sander DS 40 1+1 Disc sander DS 40 Angular transfer to the right, TWR 24/30/12/S Panel sizes: width 250 - 1200 mm, length 250 - 3000 mm, thickness 8 - 45 mm Machine 2 Machine II + infeed magazine TW ...
used
Panel thickness: 12 - 60 mm Feed speed: 18 m/min Edge thickness: 0,3 - 3 mm for coil edges Equipment: Programmable fence at the infeed Squaring device: 2 x 3,0 KW Glue application unit: A34 double edge magazine for 2 coils Lateral pressure rollers, thickness programmable, 1 driven, 2 non-driven rollers End trims HL84/85, programmable change straight/chamfer, 2 motors 0,18 kW Rough trimming: 2 x 0,55 KW Contour trimming FK 13, 2 x 0,55 KW Profile scrapers PN10 Flat scrapers Buffing unit Controlls: HOMATIC NC21
used
Includes two Rectifying Module BMR Colibrì, with documentation, an inspection is possible.
used
Max. rotational speed: 5000/min, chamfering/ calibration spindle power: 1.5/ 5.5kW, with documentation, an inspection is possible.
used
Panel thickness: 8 - 50 mm Thickness of the edges: 0,4- 3 mm Feed speed 8 - 11 m / min PU pressure rollers Equipment: Non-stick spray system Squaring unit, 2 motors 2,2 kW Panel edge heating Edge magazine for coil and strips Hot melt application with roller Airtec AT4510 unit The Airtec aggregate is positioned so you can use Airtec or the standard glue pot Motorized side pressure unit End trims, 2 motors, pneumatic positioning straight and with chamfer trimming unit above / below Contour trimming unit Profile scraping unit Glue scraping unit Polishing unit Detergent spray system central lubrication Powertouch control
used
Fixed side at the left Feedspeed 18 - 25 m/min Working width min 60mm for panel thickness 22mm, 105mm for panel thickness 40mm Panel overhang 30mm Panel thickness 8 - 60 mm in stead of 12 - 40 mm (with limitations) Coil edge thickness: 0,3 - 3 mm, strips 0,4 - 20 mm Coil diameter 830 mm Equipment: Sprayers release agent Squaring device with 2 motors each 3 kW Edge heating Edge magazine for 2 coils, guillotine for edges up to 3 mm Glueing part A20 with quickmelt application Lateral pressure zone K, 1 driven and 6 after pressing rollers End trims HL84, 2 motors each 0,8kW Rough trimming, 2 motors 1,5kW Contour trimming, 2 exchange units Profile scraping PN10 Flat scrapers FA11 Sprayers cleaning agent Buffing Automation package straight/chamfer: -Automatic adjustment infeed fence -Automatic setting of pressure rollers -Pneumatic setting of end trims -Pneumatic setting of rough trims -Automa ...
used
Single sided edge bander with squaring device Edges: 0,4 to 12 mm Panel thickness: 10 to 55 mm Min. panel width: 60 mm Feed speed 12,5 m/min Equipment: Squaring device Heating zone Coil- and stripmagazine Glue unit Pressure zone End trimmer Chamfer trimming Mutlifunctional milling aggregate Profile scraping glue scrapers Buffing